tag. All controllers that are not BCM5755 or higher have 4GB
boundary DMA bug. Previously bge(4) used 32bit DMA address to
workaround the bug(r199670). However this caused the use of bounce
buffers such that it resulted in poor performance for systems which
have more than 4GB memory. Because bus_dma(9) honors boundary
restriction requirement of DMA tag for dynamic buffers, having a
separate TX/RX mbuf DMA tag will greatly reduce the possibility of
using bounce buffers. For DMA buffers allocated with
bus_dmamem_alloc(9), now bge(4) explicitly checks whether the
requested memory region crossed the boundary or not.
With this change, only the DMA buffer that crossed the boundary
will use 32bit DMA address. Other DMA buffers are not affected as
separate DMA tag is created for each DMA buffer.
Even if 32bit DMA address space is used for a buffer, the chance to
use bounce buffer is still very low as the size of buffer is small.
This change should eliminate most usage of bounce buffers on
systems that have more than 4GB memory.
More correct fix would be teaching bus_dma(9) to honor boundary
restriction for buffers created with bus_dmamem_alloc(9) but it
seems that is not easy.
While I'm here cleanup bge_dma_map_addr() and remove unnecessary
member variables in bge_dmamap_arg structure.
Tested by: marcel
gnu/lib/libobjc and sys/boot/i386/boot2, so it also works when using
absolute paths and/or options, as in CC="/absolute/path/clang -foo".
Approved by: rpaulo (mentor)
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
signals, because it is managed by debugger, however a normal signal sent to
a interruptibly sleeping thread wakes up the thread so it will handle the
signal when the process leaves the stopped state.
PR: 150138
MFC after: 1 week
of the lower level vnode is incremented to greater than 1 when
the upper level vnode's v_usecount is greater than one. This
is necessary for the NFS clients, so that they will do a silly
rename of the file instead of actually removing it when the
file is still in use. It is "racy", since the v_usecount is
incremented in many places in the kernel with
minimal synchronization, but an extraneous silly rename is
preferred to not doing a silly rename when it is required.
The only other file systems that currently check the value
of v_usecount in their VOP_REMOVE() functions are nwfs and
smbfs. These file systems choose to fail a remove when the
v_usecount is greater than 1 and I believe will function
more correctly with this patch, as well.
Tested by: to.my.trociny at gmail.com
Submitted by: to.my.trociny at gmail.com (earlier version)
Reviewed by: kib
MFC after: 2 weeks
heavy I/O load.
Many thanks to LSI for continuing to support FreeBSD.
PR: kern/149968
Submitted by: LSI (Tom Couch)
Reported by: Kai Kockro <kkockro web de>
Tested by: Kai Kockro, jpaetzel
MFC after: 7 days
least one execute bit set, otherwise execve(2) will return EACCES even
for an user with PRIV_VFS_EXEC privilege.
Add the check also to vaccess(9), vaccess_acl_nfs4(9) and
vaccess_acl_posix1e(9). This makes access(2) to better agree with
execve(2). Because ZFS doesn't use vaccess(9) for VEXEC, add the check
to zfs_freebsd_access() too. There may be other file systems which are
not using vaccess*() functions and need to be handled separately.
PR: kern/125009
Reviewed by: bde, trasz
Approved by: pjd (ZFS part)
unused files.
- remove clock.c and clock.h, these are not used after the new timer
code was added.
- remove duplicated include files, fix header file ordering, remove
some unneeded includes.
- rename mips/rmi/shared_structs.h which contains the RMI boot loader
interface to mips/rmi/rmi_boot_info.h. Remove unused files
mips/rmi/shared_structs_func.h and sys/mips/rmi/shared_structs_offsets.h
- merge mips/rmi/xlrconfig.h and mips/rmi/rmi_mips_exts.h, and remove
duplicated functions.
- nlge - minor change to remove unneeded argument.
- Add FreeBSD svn keyword for headers
pseudo-interface. This leads to a panic due to uninitialized
if_broadcastaddr address. Initialize it and implement ip_output()
method to prevent mbuf leak later.
ipfw pseudo-interface should never send anything therefore call
panic(9) in if_start() method.
PR: kern/149807
Submitted by: Dmitrij Tejblum
MFC after: 2 weeks
PMAP_DIAGNOSTIC was eliminated from amd64/i386, and, in fact, the
non-MIPS parts of the kernel, several years ago. Any of the interesting
checks were turned into KASSERT()s. Basically, the motivation was that
lots of people run with INVARIANTS but no one runs with DIAGNOSTIC.
panic strings needn't and shouldn't have a terminating newline.
Finally, there is one functional change. The sched_pin() in
pmap_remove_pages() is an artifact of the way we temporarily map page
table pages on i386. (The mappings are processor private. We don't do
a system-wide shootdown.) It isn't needed by MIPS.
Tested by: jchandra
Submitted by: alc
nfsd_recalldelegation() function, since this function is called
by nfsd threads when they are handling NFSv2 or NFSv3 RPCs, where
no reference count would have been acquired.
MFC after: 2 weeks
the correct mutex when checking nfsv4root_lock. Although this
could be fixed by adding mutex lock/unlock calls, zack.kirsch at
isilon.com suggested a better fix that uses a non-blocking
acquisition of a reference count on nfsv4root_lock. This fix
allows the weird NFSLOCKSTATE(); NFSUNLOCKSTATE(); synchronization
to be deleted. This patch applies this fix.
Tested by: zack.kirsch at isilon.com
MFC after: 2 weeks
and XAUI 10G interfaces in addition RGMII/SGMII 1G interfaces. This driver
is work in progress.
board.c and board.h expanded to include more info.
Only one of rge and nlge can be enabled at a time, rge will be deprecated
when nlge stabilizes.
Submitted by: Sriram Gorti <srgorti at netlogicmicro com>
Fix the switching on/off of PF and NR-SACKs using sysctl.
Add minor improvement in handling malloc failures.
Improve the address checks when sending.
MFC after: 4 weeks
for socket, when specified POLLIN|POLLOUT in events, you would have one
selfd registered for receiving socket buffer, and one for sending. Now,
if both events are not ready to fire at the time of the initial scan,
but are simultaneously ready after the sleep, pollrescan() would iterate
over the pollfd struct twice. Since both times revents is not zero,
returned value would be off by one.
Fix this by recalculating the return value in pollout().
PR: kern/143029
MFC after: 2 weeks
- better ACL caching and speedup of ACL permission checks
- faster handling of stat()
- lowered mutex contention in the read/writer lock (rrwlock)
- several related bugfixes
Detailed information (OpenSolaris onnv changesets and Bug IDs):
9749:105f407a2680
6802734 Support for Access Based Enumeration (not used on FreeBSD)
6844861 inconsistent xattr readdir behavior with too-small buffer
9866:ddc5f1d8eb4e
6848431 zfs with rstchown=0 or file_chown_self privilege allows user to "take" ownership
9981:b4907297e740
6775100 stat() performance on files on zfs should be improved
6827779 rrwlock is overly protective of its counters
10143:d2d432dfe597
6857433 memory leaks found at: zfs_acl_alloc/zfs_acl_node_alloc
6860318 truncate() on zfsroot succeeds when file has a component of its path set without access permission
10232:f37b85f7e03e
6865875 zfs sometimes incorrectly giving search access to a dir
10250:b179ceb34b62
6867395 zpool_upgrade_007_pos testcase panic'd with BAD TRAP: type=e (#pf Page fault)
10269:2788675568fd
6868276 zfs_rezget() can be hazardous when znode has a cached ACL
10295:f7a18a1e9610
6870564 panic in zfs_getsecattr
Approved by: delphij (mentor)
Obtained from: OpenSolaris (multiple Bug IDs)
MFC after: 2 weeks
This provides a noticeable write speedup, especially on pools with
less than 30% of free space.
Detailed information (OpenSolaris onnv changesets and Bug IDs):
11146:7e58f40bcb1c
6826241 Sync write IOPS drops dramatically during TXG sync
6869229 zfs should switch to shiny new metaslabs more frequently
11728:59fdb3b856f6
6918420 zdb -m has issues printing metaslab statistics
12047:7c1fcc8419ca
6917066 zfs block picking can be improved
Approved by: delphij (mentor)
Obtained from: OpenSolaris (Bug ID 6826241, 6869229, 6918420, 6917066)
MFC after: 2 weeks
Actually it is hard to properly handle such a failure, especially in MNT_UPDATE
case. The only reason for the vfs_allocate_syncvnode() function to fail is
getnewvnode() failure. Fortunately it is impossible for current implementation
of getnewvnode() to fail, so we can assert this and make
vfs_allocate_syncvnode() void. This in turn free us from handling its failures
in the mount code.
Reviewed by: kib
MFC after: 1 month
but because of a bug it was a no-op, so we were still using offsets in native
byte order for the host. Do it properly this time, bump version to 4 and set
the G_ELI_FLAG_NATIVE_BYTE_ORDER flag when version is under 4.
MFC after: 2 weeks
configuration function. For failed memory allocations, em(4)/lem(4)
called panic(9) which is not acceptable on production box.
igb(4)/ixgb(4)/ix(4) allocated the required memory in stack which
consumed 768 bytes of stack memory which looks too big.
To address these issues, allocate multicast array memory in device
attach time and make multicast configuration success under any
conditions. This change also removes the excessive use of memory in
stack.
Reviewed by: jfv
Just showing some buffer allocation error is more appropriate
action for drivers. This should fix occasional panic reported on
em(4) when driver encountered resource shortage.
Reviewed by: jfv
SMP.
We used to route all PIC based interrupts to cpu 0, and used the per-CPU
interrupt mask to enable/disable interrupts. But the interrupt threads can
run on any cpu on SMP, and the interrupt thread will re-enable the interrupts
on the CPU it runs on when it is done, and not on cpu0 where the PIC will
still send interrupts to.
The fix is move the disable/enable for PIC based interrupts to PIC, we will
ack on PIC only when the interrupt thread is done, and we do not use the
per-CPU interrupt mask.
The changes also introduce a way for subsystems to add a function that
will be called to clear the interrupt on the subsystem. Currently This is
used by the PCI/PCIe for doing additional work during the interrupt
handling.
- We are fine by only share-locking the vnode.
- Remove assertion that doesn't hold for ZFS where we cross mount points
boundaries by going into .zfs/snapshot/<name>/.
Reviewed by: rmacklem
MFC after: 1 month
(replay_alloc()) knows how to handle replay_alloc() failure.
- Eliminate 'freed_one' variable, it is not needed - when no entry is found
rce will be NULL.
- Add locking assertions where we expect a rc_lock to be held.
Reviewed by: rmacklem
MFC after: 2 weeks
supported by many BIOSes to improve performance of VESA BIOS calls for real
mode OSes but it is not our intention here. However, this may help some
platforms where the video ROMs are inaccessible after suspend, for example.
Note it may consume up to 64K bytes of contiguous memory depending on video
controller model when it is enabled. This feature can be disabled by
setting zero to 'debug.vesa.shadow_rom' loader tunable via loader(8) or
loader.conf(5). The default is 1 (enabled), for now.
provide PCI devices for various hardware such as memory controllers, etc.
These PCI buses are not enumerated via ACPI however. Add qpi(4) psuedo
bus and Host-PCI bridge drivers to enumerate these buses. Currently the
driver uses the CPU ID to determine the bridges' presence.
In collaboration with: Joseph Golio @ Isilon Systems
MFC after: 2 weeks
rather than forging ahead and interpreting garbage buffer content
and dirent structures.
This change backs out r211684 which was essentially a no-op.
MFC after: 1 week
- Use timer 7 in XLR PIC as a 32 counter
- provide pic_init_timer(), pic_set_timer(), pic_timer_count32() and
pic_timer_count() PIC timer operations.
- register this timer as platform_timecounter on rmi platform.
- style(9) fixes to mips/rmi platform files
- update pic.h to add pic_setup_intr() and use pic_setup_intr() for setting
up interrupts which are routed thru PIC.
- remove rmi_spin_mutex_safe and haslock, and make sure that the functions
are called only after mutexes are available.
- move PIC code to xlr_machdep.c
- move fast message ring code completely to on_chip.c
- move memory initialization to a new function xlr_mem_init()
- style fixes
ID, plus the ability to force '16-bit mode' which really means NE-2000
mode. Other open source drivers suggest that the Holtek misbehaves if
you allow the 8-bit probe. Also, all of the PCI chips emulate
NE-2000ish cards, so always force 16-bit mode for memory transfers.
PR: 84202 (patch not used)
succeeded and a subsequent interation failed to find an
entry to prune, it could loop infinitely, since the
"freed" variable wasn't reset to FALSE. This patch moves
setting freed FALSE to inside the loop to fix the problem.
Tested by: alan.bryan at yahoo.com
MFC after: 2 weeks
I'm not sure whether adding this logical id is correct or not
because Compex RL2000 is in the list of supported hardware list.
I guess the Compex RL2000 could be PCI variant while the controller
in question is ISA controller. It seems PNP compat id didn't match
or it had multiple compat ids so isa_pnp_probe() seemed to return
ENOENT.
PR: kern/80853
resetting needfree
needfree is checked at the very start of arc_reclaim_needed.
This change makes code easier to follow and maintain in face of
potential changed in arc_reclaim_needed.
Also, put the whole sub-block under _KERNEL because needfree can be set
only in kernel code.
To do: rename needfree to something else to aovid confusion with
OpenSolaris global variable of the same name which is used in the same
code, but has different meaning (page deficit).
Note: I have an impression that locking around accesses to this variable
as well as mutual notifications between arc_reclaim_thread and
arc_lowmem are not proper.
MFC after: 1 week
or amd64.
Sponsored by: The FreeBSD Foundation
> Description of fields to fill in above: 76 columns --|
> PR: If a GNATS PR is affected by the change.
> Submitted by: If someone else sent in the change.
> Reviewed by: If someone else reviewed your modification.
> Approved by: If you needed approval for this commit.
> Obtained from: If the change is from a third party.
> MFC after: N [day[s]|week[s]|month[s]]. Request a reminder email.
> Security: Vulnerability reference (one per line) or description.
> Empty fields above will be automatically removed.
M dtrace/dtraceall/dtraceall.c
M dtrace/Makefile
Clang to compile this file: it was using the builtin memcpy and we want
to use the memcpy defined in gptboot.c. (Clang can't compile boot2 yet).
Submitted by: Dimitry Andric <dimitry at andric.com>
Reviewed by: jhb
standard kill(). On other systems, SI_LWP is generated by lwp_kill().
This will allow conforming applications to differentiate between
signals generated by standard events and those generated by other
implementation events in a manner compatible with existing practice.
- Bump __FreeBSD_version
support WOL. Some controllers require additional 3-wire auxiliary
remote wakeup connector to draw power. More recent xl(4)
controllers may not need the wakeup connector though.
initialize controller from a known good state. Previously driver
used to issue controller reset while TX/RX DMA are in progress.
I guess resetting controller in active TX/RX DMA cycle is to ensure
stopping I/Os in xl_shutdown(). I remember some buggy controllers
didn't respond with stop command if controller is under high
network load at the time of shutdown so resetting controller was
the only safe way to stop the I/Os. However, from my experiments,
controller always responded with stop command under high network
load so I think it's okay to remove the xl_reset() in
device_shutdown handler.
Resetting controller also will clear configured RX filter which
in turn will make WOL support hard because driver have to reprogram
RX filter in WOL handler as well as setting station address.
Use MACHINE_CPUARCH in preference to MACHINE_ARCH. The former is the
source code location of the machine, the latter the binary output. In
general, we want to use MACHINE_CPUARCH instead of MACHINE_ARCH unless
we're tesitng for a specific target. The isn't even moot for
i386/amd64 where there's momemntum towards a MACHINE_CPUARCH == x86,
although a specific cleanup for that likely would be needed...
the uio_offset adjustment instead to calculate a correct *len.
Without this change, we run off the end of the directory data
we're reading and panic horribly for nfs filesystems.
MFC after: 1 week
register mapping. I'm not sure whether it comes from the fact that
controllers live behind certain PCI brdge(PLX PCI 6152 33BC) and
the bridge has some issues in handling I/O space register mapping.
Unfortunately it's not possible to narrow down to an exact
controller that shows this issue because RealTek used the same PCI
device/revision id again. In theory, it's possible to check parent
PCI bridge device and change rl(4) to use memory space register
mapping if the parent PCI bridge is PLX PCI 6152. But I didn't try
to do that and we wouldn't get much benefit with added complexity.
Blindly switching to use memory space register mapping for rl(4)
may make most old controllers not to work. At least, I don't want
to take potential risk from such change. So use I/O space register
mapping by default but give users chance to override it via a
tunable. The tunable to use memory space register mapping would be
given by adding the following line to /boot/loader.conf file.
dev.rl.%d.prefer_iomap="0"
This change makes P811B quad-port work with this tunable.
Tested by: Nikola Kalpazanov ( n.kalpazanov <> gmail dot com )
MFC after: 1 week
devfs_populate(). This is a prerequisite for the automatic removal of
empty directories which will be committed in the future.
Reviewed by: kib (previous version)
Sponsored by: The FreeBSD Foundation
> Description of fields to fill in above: 76 columns --|
> PR: If a GNATS PR is affected by the change.
> Submitted by: If someone else sent in the change.
> Reviewed by: If someone else reviewed your modification.
> Approved by: If you needed approval for this commit.
> Obtained from: If the change is from a third party.
> MFC after: N [day[s]|week[s]|month[s]]. Request a reminder email.
> Security: Vulnerability reference (one per line) or description.
> Empty fields above will be automatically removed.
M sys/fasttrap_impl.h
use '-' in probe names, matching the probe names in Solaris.[1]
Add userland SDT probes definitions to sys/sdt.h.
Sponsored by: The FreeBSD Foundation
Discussed with: rwaston [1]
Right now unionfs only allows filesystems to be mounted on top of
another if it supports whiteouts. Even though I have sent a patch to
daichi@ to let unionfs work without it, we'd better also add support for
whiteouts to tmpfs.
This patch implements .vop_whiteout and makes necessary changes to
lookup() and readdir() to take them into account. We must also make sure
that when adding or removing a file, we honour the componentname's
DOWHITEOUT and ISWHITEOUT, to prevent duplicate filenames.
MFC after: 1 month
datagrams with checksum value 0 when TX UDP checksum offloading is
enabled. Generating UDP checksum value 0 is RFC 768 violation.
Even though the probability of generating such UDP datagrams is
low, I don't want to see FreeBSD boxes to inject such datagrams
into network so disable UDP checksum offloading by default. Users
still override this behavior by setting a sysctl variable or loader
tunable, dev.bge.%d.forced_udpcsum.
I have no idea why this issue was not reported so far given that
bge(4) is one of the most commonly used controller on high-end
server class systems. Thanks to andre@ who passed the PR to me.
PR: kern/104826
problems compiling it, but it just gets too big at the moment, even
with -Os. This is not applicable to gptboot, though.
Submitted by: Dimitry Andric <dimitry at andric.com>
LK_CANRECURSE after a lock is created. Use them to implement macros that
otherwise manipulated the flags directly. Assert that the associated
lockmgr lock is exclusively locked by the current thread when manipulating
these flags to ensure the flag updates are safe. This last change required
some minor shuffling in a few filesystems to exclusively lock a brand new
vnode slightly earlier.
Reviewed by: kib
MFC after: 3 days
of p_traceflag that is stored in the kinfo_proc structure. It is still
racey even with the lock and the code will read a consistent snapshot of
the flag without the lock.
* Add a function to write to the relevant PLL register
* Break out the PLL configuration for the AR71XX into the CPU ops,
lifted from if_arge.c.
* Add the AR91XX PLL configuration ops, using the AR91XX register
definitions.
This is untested but should at least allow an AR724X to boot.
The current code is lacking the detail needed to expose the PCIe bus.
It is also lacking any NIC, PLL or flush/WB code.
This works well enough to bring a system up to single-user mode
using an MDROOT.
Known Issues:
* The EHCI USB doesn't currently work and will panic the kernel during
attach.
* The onboard ethernet won't work until the PLL routines have been
fleshed out and shoe-horned into if_arge.
* The WMAC device glue (and quite likely the if_ath support)
hasn't yet been implemented.
Add kernel side support for Secure Neighbor Discovery (SeND), RFC 3971.
The implementation consists of a kernel module that gets packets from
the nd6 code, sends them to user space on a dedicated socket and reinjects
them back for further processing.
Hooks are used from nd6 code paths to divert relevant packets to the
send implementation for processing in user space. The hooks are only
triggered if the send module is loaded. In case no user space
application is connected to the send socket, processing continues
normaly as if the module would not be loaded. Unloading the module
is not possible at this time due to missing nd6 locking.
The native SeND socket is similar to a raw IPv6 socket but with its own,
internal pseudo-protocol.
Approved by: bz (mentor)
* Implement a SoC probe function, from Linux, which determines the
SoC family, type and revision. This only probes the AR71xx series
SoC and (currently) panics on others.
* Migrate some of the AR71XX specific hardware init (USB device, determining
system frequencies) into using the cpuops introduced in an earlier commit.
Other SoC specific hardware stuff (per-device flush/WB, GPIO pin wiring,
Ethernet PLL setup, other things I've likely missed) will be introduced in
subsequent commits.
Reviewed by: imp@
Obtained from: (partially) Linux
it must reset its congestion window back to the initial window.
RFC3390 has increased the initial window from 1 segment to up to
4 segments.
The initial window increase of RFC3390 wasn't reflected into the
restart window which remained at its original defaults of 4 segments
for local and 1 segment for all other connections. Both values are
controllable through sysctl net.inet.tcp.local_slowstart_flightsize
and net.inet.tcp.slowstart_flightsize.
The increase helps TCP's slow start algorithm to open up the congestion
window much faster.
Reviewed by: lstewart
MFC after: 1 week
sysctl's and remove any side effects.
Both sysctl's share the same backend infrastructure and due to the
way it was implemented enabling net.inet.tcp.log_in_vain would also
cause log_debug output to be generated. This was surprising and
eventually annoying to the user.
The log output backend is kept the same but a little shim is inserted
to properly separate log_in_vain and log_debug and to remove any side
effects.
PR: kern/137317
MFC after: 1 week
1. On n64, use XKPHYS to map page table pages instead of KSEG0. Maintain
just one freepages list on n64.
The changes are mainly to introduce MIPS_PHYS_TO_DIRECT(pa),
MIPS_DIRECT_TO_PHYS(), which will use KSEG0 in 32 bit compilation
and XKPHYS in 64 bit compilation.
2. Change macro based PMAP_LMEM_MAP1(), PMAP_LMEM_MAP2(), PMAP_LMEM_UNMAP()
to inline functions.
3. Introduce MIPS_DIRECT_MAPPABLE(pa), which will further reduce the cases
in which we will need to have a special case for 64 bit compilation.
4. Update CP0 hazard definitions for CPU_RMI - the cpu does not need any
nops
Reviewed by: neel
number of syncache entries into account for the surplus we add to account
for a possible increase of records in the re-entry window.
Discussed with: jhb, silby
MFC after: 1 week
Each of these SoCs have different devices, different hardware initialisation
methods and, quite likely, different quirks. These functions will abstract
out the SoC differences and keep these differences out of the drivers (eg
USB init, if_arge, etc.)
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
memory size estimate to userland for pcb list sysctls. The previous
behavior of a "slop" of n/8 does not work well for small values of n
(e.g. no slop at all if you have less than 8 open UDP connections).
Reviewed by: bz
MFC after: 1 week
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
