are currently all bad BIOS revisions that will never be able to support
ACPI. They were derived by examining which BIOS's are blacklisted by other
operating systems. Other types of quirks will be possible here as well.
Ultra2 users may want to set OFWCONS_POLL_HZ to a value of '20'.
I have left default value at '4' as higher values can consume a more
than is acceptable amount of CPU, and we don't have a consensus yet
what is an optimal value.
Submitted by: Pyun YongHyeon <yongari@kt-is.co.kr>
smp_rendezvous() to ensure we run on the BSP. This reverts rev 1.128.
Add a comment indicating that MI code should be the one that runs all
shutdown functions on the BSP with the APs halted. This should work
around problems in power off while waiting for the MI code to be improved.
actually used. For most ACPI devices this means deferring the call
until bus_alloc_resource().
- Add a function acpi_config_intr() to call BUS_CONFIG_INTR() for an
ACPI IRQ resource using the trigger mode and polarity information
stored in the ACPI resource object.
- Add a function acpi_lookup_irq_resource() to lookup the ACPI IRQ
resource that corresponds to a specified rid and new-bus resource.
- Have the ACPI PCI bridge driver call BUS_CONFIG_INTR() on interrupts
that it routes through link devices.
- Remove needactivate variable from acpi_alloc_resource() by changing the
function not modify the flags variable but just mask off RF_ACTIVE when
calling rman_reserve_resource().
Reviewed by: njl (1, an earlier version)
device associated with any PCI devices that are enumerated in the ACPI
tree when adding children to an ACPI PCI bus and remove the duplicate
ACPI-only device_t and replace the device_t associated with the handle with
the ACPI and PCI aware device_t.
Several changes:
* Implement read for ulpt.
* If the device is not opened for reading, occasionally drain any
data the printer might have (but don't hammer the printer with reads).
* Lower the buffer size to one page.
The driver seems to work with more printers now.
Obtained from: NetBSD
the GEOM topology.
There are still issues with not detaching from cam correctly such that
upon a device detach there's an invalid pointer dereference from the
later call to cam_rescan().
that are on a CISS bus to be exported up to CAM and made available as normal
devices. This will typically add one or two buses to CAM, which will be
numbered starting at 32 to allow room for CISS proxy buses. Also, the CISS
firmware usually hides disk devices, but these can also be exposed as 'pass'
devices if you set the hw.ciss.expose_hidden_physical tunable.
Sponsored by: Tape Laboratories, Inc.
MFC After: 3 days
least the pci device unloadable
- Use ttymalloc() rather than a plain malloc to allocate the
rp->rp_tty ttys. This is now required due to the recent locking
changes to ttys and prevents a panic due to locking an unitialized
t_mtx.
- Allow the pci driver to be unloaded. This involved moving
the call rp_releaseresource() to the end of rp_pcireleaseresource(),
since rp_pcireleaseresource() uses ctlp->dev, which is freed
by rp_releaseresource().
- Allow the generic part of the driver to be unattached by providing
a hook to cancel timeouts.
Glanced at by: obrien
The big lines are:
NODEV -> NULL
NOUDEV -> NODEV
udev_t -> dev_t
udev2dev() -> findcdev()
Various minor adjustments including handling of userland access to kernel
space struct cdev etc.
timeout values in the CAM CCBs. Divide by 1000 to get values in seconds
which are what ata(4) timeouts internally use.
This does lose granularity, though, and small values can now round down
to zero. It's probably worth making all ata(4) timeouts in terms of
hz/ticks/milliseconds/something.
