produced by miniperl during buildworld phase.
- While at it, do loading of SelfLoader only when it is needed, and in
place where it is needed.
Submitted by: tobez@tobez.org (who is doing way too much good work
and is in need of the Commit Bit punishment)
of a/x -> b and then negotiate a/x -> c by simply expecting SIOCAIFADDR
to do the change.
This was broken by the last commit that optimised out the deletion and
re-addition of the same a/x -> b combination, and forgot to compare
the old/new destination addresses.
Conveniently enough, this problem didn't effect setups where the
default route goes via the ppp link, and most other setups don't
care what the the destination address is actually set to. It broke
test environments where ppp connects to the local machine rather
badly though....
- Allocate zeroed memory in ether_resolvemulti() to prevent equal() from
comparing garbage and determining that two otherwise-equal sockaddr_dls
are different.
- Fill in all required fields of the sockaddr_dl
- Actually copy the multicast address into the sockaddr_dl when calling
if_addmulti()
- Don't claim that we don't have a way to resolve layer 3 addresses into
layer 2 addresses; use the ethernet way.
account at creation, create accounts with a "*" password (so you can
use alternate authentication schemes without fearing a "default" password
biting you later), and blank passwords.
Yes, adduser could create a blank password account, but this makes it
slightly more difficult to shoot yourself in the foot.
The /etc/adduser.conf entries are:
# use password-based authentication for new users
# defaultusepassword = "yes" | "no"
defaultusepassword = "yes"
# enable account password at creation
# (the password will be prepended with a star if the account isn't enabled)
# defaultenableaccount = "yes" | "no"
defaultenableaccount = "yes"
# allow blank passwords
# defaultemptypassword = "yes" | "no"
defaultemptypassword = "no"
Requested by: alfred
Reviewed by: alfred
handling, SMPng always switches the npx context away from curproc
before calling the handler, so the handler always paniced. When using
exception 16 exception handling, SMPng sometimes switches the npx
context away from curproc before calling the handler, so the handler
sometimes paniced. Also, we didn't lock the context while using it,
so we sometimes didn't detect the switch and then paniced in a less
controlled way.
Just lock the context while using it, and return without doing anything
except clearing the busy latch if the context is not for curproc. This
fixes the exception 16 case and makes the IRQ13 case harmless. In both
cases, the instruction that caused the exception is restarted and the
exception repeats. In the exception 16 case, we soon get an exception
that can be handled without doing anything special. In the IRQ13 case,
we get an easy to kill hung process.
valid keyword handling and the holiday file processing
- don't issue a warning in case the holiday file is not found
- enable inclusion of ../Makefile.inc to reenable compiling-in monitor
support into isdnd
- update manual page, add a comma and correct authors mail address
least in -w's case, simply unsetting the correct bit in init_flags was not
enough. The bit may be reset later if, say, the filesystem is marked `ro'
in fstab. The command line option should override the fstab setting, but
did not. The implementation of -r was changed for consistency.
PR: 26886
Reviewed by: archie
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
drivers.
- change daprevent() to set CAM_RETRY_SELTO and SF_RETRY_UA when it calls
cam_periph_runccb().
- change the pt(4) driver to ignore unit attentions
- change the targ(4) driver to retry selection timeouts
- clean up a few formatting glitches in the targ(4) driver
Reviewed by: gibbs
for a module overridden by BSDPAN instead of the original module.
* Fix wrong manual section numbers in SEE ALSO.
* Add `Revision 42' to the beer-ware license. The BSDPAN author did not
originally get the reference and removed the revision from original
phk's version.
Submitted by: Anton Berezin <tobez@tobez.org>
other "system" header files.
Also help the deprecation of lockmgr.h by making it a sub-include of
sys/lock.h and removing sys/lockmgr.h form kernel .c files.
Sort sys/*.h includes where possible in affected files.
OK'ed by: bde (with reservations)
