machdep.o is a defined to be a target in 2 places. This was caused by
the addition of the LOAD_ADDRESS stuff. Removed the extranious target
of machdep.o.
* patch from vak@zebub.msk.su (Serge V.Vakulenko) to work around
* a hardware bug in cheap WD clone boards where the PROM checksum
* byte is always zero
it relocates it to be after the BIOS memory hole instead of right below
the 640K limit.
THANK YOU CHRIS!!!
From: <cgd@postgres.Berkeley.EDU>
Date: Wed, 29 Sep 93 18:49:58 -0700
basically, reserve a new 32k space right after firstaddr,
and put the buffer space there...
the diffs are below, and are in ~cgd/sys/i386/i386 (in machdep.c)
on freefall. i obviously can't test them, so if some of you would
look the diffs over and try them out...
Date: Thu, 30 Sep 1993 15:13:17 +0300
Description:
Old wt driver is too incomplete and buggy.
It does not support Archive controllers, BSD-like
tape ioctls, multiple tape controllers, different
tape density etc.
Fix:
This driver is a replacement of the old one.
It was not tested on different controllers, though.
This is the streamer tape driver for 386bsd and FreeBSD,
which supports Wangtek and Archive controllers.
It was developed as a replacement of the old Wangtek
tape driver from CMU.
In comparison with the CMU driver, this version has the following enhancements:
1) Support for Archive SC402 and SC499 tape controllers added.
2) Support for up to three tape controllers on the same machine.
3) Support for BSD-style ioctls MTIOCGET, MTIOCTOP.
Mt command now works adequately with this driver.
4) Asynchronous REWIND and FSF operations, close() will not wait
until they finish. The next open() will wait for it instead.
5) Use of WTQICMD ioctl is limited to ERASE and RETENS operations.
This prevents the user from locking the tape driver by strange
tape operations.
6) Tape density switching added.
7) The status of the process, blocked on the tape operation,
is displayed at the WCHAN column of the `ps' command as:
wtread reading data from the tape
wtwrite writing data to the tape
wtrfm reading the tape marker
wtwfm writing the tape marker
wtrew rewinding the tape
wterase doing WTQICMD ERASE operation
wtretens doing WTQICMD RETENS operation
wtorew doing MTIOCTOP REW/OFFL operation
wtorfm doing MTIOCTOP FSF operation
wtowfm doing MTIOCTOP WEOF operation
Block interface (writing blocks less than 2048 bytes) is not functioning
pwoperly. Use raw interface instead.
* Added software NIC reset in NE probe to work around a problem
* with some NE boards where the 8390 doesn't reset properly on
* power-up. Remove initialization of IMR/ISR in the NE probe
* because this is inherent in the reset.
* added no multi-buffer override for 3c503
*
* Revision 2.1 93/09/29 12:32:12 davidg
* changed multi-buffer count for 16bit 3c503's from 5 to 2 after
* noticing that the transmitter becomes idle because of so many
* packets to load.
*
* Revision 2.0 93/09/29 00:00:19 davidg
* many changes, rewrites, additions, etc. Now supports the
* NE1000, NE2000, WD8003, WD8013, 3C503, 16bit 3C503, and
* a variety of similar clones. 16bit 3c503 now does multi
* transmit buffers. Nearly every part of the driver has
* changed in some way since rev 1.30.
Date: Wed, 29 Sep 1993 01:54:53 +0300
To bring this error try to make two swap partitons on one disk:
one of the partitions will be not recognized.
Fix is simple: set uninitialized val variable.
Date: Tue, 28 Sep 1993 09:03:13 +0100 (MET)
The only place I found with a printf("status %x") is in /sys/i386/isa/lpt.c,
and looks much like a left-over debugging printout...
And it was... I changed it to an lprintf (which is defined if debuggin is on)
Rod
Added STRIP=, DBSYM=, and LOAD_ADDRESS?=
Now use LOAD_ADDRESS for linking kernel and for dbsym, added strip -x to
cut kernel size.
Added machde.o: dependency, this will be needed in the future, and for
now it does not hurt anyone.
Cleaned out conf.o: dependency, mkdep does the right things. Same for
param.c:
This is really a Merge in of NetBSD's Makefile.i386, here is the relevant
rlog info:
----------------------------
revision 1.27
date: 1993/08/27 23:58:20; author: brezak; state: Exp; lines: +2 -2
Need LOAD_ADDRESS for depend pass.
----------------------------
revision 1.25
date: 1993/07/19 16:52:16; author: mycroft; state: Exp; lines: +3 -3
Add ${DEBUG} to CFLAGS and -f to dbsym.
----------------------------
revision 1.22
date: 1993/07/18 10:08:22; author: mycroft; state: Exp; lines: +5 -6
Change to work with new config stuff for specifying load address.
----------------------------
revision 1.20
date: 1993/07/18 09:47:40; author: mycroft; state: Exp; lines: +6 -5
Use new -T option to dbsym.
----------------------------
revision 1.17
date: 1993/07/11 08:42:22; author: cgd; state: Exp; lines: +2 -2
don't ignore errors from dbsym... it might say that, e.g. there's
not enough symbol space!
----------------------------
revision 1.14
date: 1993/06/06 23:29:03; author: cgd; state: Exp; lines: +2 -2
make conf.o actually depend on conf.c...
----------------------------
revision 1.8
date: 1993/04/29 03:27:39; author: cgd; state: Exp; lines: +5 -10
use ed instead of ex. the script to use is identical, and we might
want to switch back to using ex when our ex supports -.
----------------------------
revision 1.5
date: 1993/03/24 18:48:57; author: cgd; state: Exp; lines: +1 -1
now use absolute path for dbsym
----------------------------
Date: Sun, 12 Sep 1993 18:19:05 -0500
This will allow you to compile and run a freebsd kernel with shared
memory support. I haven't tested the shm*() calls yet.
You run out of page table descriptors if you specify 4Mb of sharable
memory (SHMMAXPGS=1024). I don't know what the limit is, but
SHMMAXPGS=64 works. Rich
Date: Fri, 24 Sep 1993 10:19:20 -0700
Fixed bug that was reported (with patch) on gnu.utils.bug.
Immediate operands of the pushw instruction were being output as 32
bits, rather than the 16 bits they were supposed to be.
