obliterate possible error from sleep with errors from
umtxq_check_susp(), when looping to clear URWLOCK_{READ,WRITE}_WAITERS.
Noted and reviewed by: vangyzen
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
If there was some error, e.g. the sleep was interrupted, as in the
referenced PR, do_rw_rdlock() did not cleared URWLOCK_READ_WAITERS.
Since unlock only wakes up write waiters when there is no read
waiters, for URWLOCK_PREFER_READER kind of locks, the result was
missed wakeups for writers.
In particular, the most visible victims are ld-elf.so locks in
processes which loaded libthr, because rtld locks are urwlocks in
prefer-reader mode. Normal rwlocks fall into prefer-reader mode only
if thread already owns rw lock in read mode, which is not typical and
correspondingly less visible. In the PR, unowned rtld bind lock was
waited for in the process where only one thread was left alive.
Note that do_rw_wrlock() correctly clears URWLOCK_WRITE_WAITERS in
case of errors.
Reported and tested by: longwitz@incore.de
PR: 211947
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
If the caller of sem_post() wakes up a thread sleeping via sem_wait()
before it clears the has_waiters flag, the caller of sem_wait() has no way of
knowing when it is safe to destroy the semaphore and reuse the memory. This is
because the caller of sem_post() may be interrupted between the wake step and
the clearing of has_waiters. It will then write into the has_waiters flag in
userspace after being preempted for some unknown amount of time.
Reviewed by: jhb, kib, vangyzen
Approved by: kib (mentor), vangyzen (mentor)
MFC after: 2 weeks
Sponsored by: Dell Inc.
Differential Revision: https://reviews.freebsd.org/D7505
intention of the POSIX IEEE Std 1003.1TM-2008/Cor 1-2013.
A robust mutex is guaranteed to be cleared by the system upon either
thread or process owner termination while the mutex is held. The next
mutex locker is then notified about inconsistent mutex state and can
execute (or abandon) corrective actions.
The patch mostly consists of small changes here and there, adding
neccessary checks for the inconsistent and abandoned conditions into
existing paths. Additionally, the thread exit handler was extended to
iterate over the userspace-maintained list of owned robust mutexes,
unlocking and marking as terminated each of them.
The list of owned robust mutexes cannot be maintained atomically
synchronous with the mutex lock state (it is possible in kernel, but
is too expensive). Instead, for the duration of lock or unlock
operation, the current mutex is remembered in a special slot that is
also checked by the kernel at thread termination.
Kernel must be aware about the per-thread location of the heads of
robust mutex lists and the current active mutex slot. When a thread
touches a robust mutex for the first time, a new umtx op syscall is
issued which informs about location of lists heads.
The umtx sleep queues for PP and PI mutexes are split between
non-robust and robust.
Somewhat unrelated changes in the patch:
1. Style.
2. The fix for proper tdfind() call use in umtxq_sleep_pi() for shared
pi mutexes.
3. Removal of the userspace struct pthread_mutex m_owner field.
4. The sysctl kern.ipc.umtx_vnode_persistent is added, which controls
the lifetime of the shared mutex associated with a vnode' page.
Reviewed by: jilles (previous version, supposedly the objection was fixed)
Discussed with: brooks, Martin Simmons <martin@lispworks.com> (some aspects)
Tested by: pho
Sponsored by: The FreeBSD Foundation
breaking the ABI. Special value is stored in the lock pointer to
indicate shared lock, and offline page in the shared memory is
allocated to store the actual lock.
Reviewed by: vangyzen (previous version)
Discussed with: deischen, emaste, jhb, rwatson,
Martin Simmons <martin@lispworks.com>
Tested by: pho
Sponsored by: The FreeBSD Foundation
self-documented, and eases addition of new ops.
For the similar reasons, eliminate UMTX_OP_MAX. nitems() handles the
only use of the symbol.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
It looks like umtx_key_get() has the addition and subtraction the wrong
way around, meaning that it fails to match in certain cases. This causes
the cloudlibc unit tests to deadlock in certain cases.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3287
in this area and by the Clang static analyzer.
Remove some dead assignments.
Fix a typo in a panic string.
Use umtx_pi_disown() instead of duplicate code.
Use an existing variable instead of curthread.
Approved by: kib (mentor)
MFC after: 3 days
Sponsored by: Dell Inc
currently a spin lock. Apparently, the only reason for this is that
umtx_thread_exit() is called under the process spinlock, which put the
requirement on the umtx_lock. Note that the witness static order list
is wrong for the umtx_lock, umtx_lock is explicitely before any thread
lock, so it is also before sleepq locks.
Change umtx_lock to be the sleepable mutex. For the reason above, the
calls to umtx_thread_exit() are moved from thread_exit() earlier in
each caller, when the process spin lock is not yet taken.
Discussed with: jhb
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
to its previous, unowned state. This avoids compounding an existing
problem of inconsistent ownership.
Submitted by: Eric van Gyzen <eric_van_gyzen@dell.com>
Obtained from: Dell Inc.
PR: 198914
MFC after: 1 week
is empty, look up the umtx_pi and disown it if the current thread owns it.
This can happen if a signal or timeout removed the last waiter from
the queue, but there is still a thread in do_lock_pi() holding a reference
on the umtx_pi. The unlocking thread might not own the umtx_pi in this case,
but if it does, it must disown it to keep the ownership consistent between
the umtx_pi and the umutex.
Submitted by: Eric van Gyzen <eric_van_gyzen@dell.com>
with advice from: Elliott Rabe and Jim Muchow, also at Dell Inc.
Obtained from: Dell Inc.
PR: 198914
subverted by userspace into cycle. Both umtx_propagate_priority() and
umtx_repropagate_priority() would then loop infinitely, owning the
spinlock.
Check for the cycle using standard Floyd' algorithm before doing the
pass in the affected functions. Add simple check for condition of
tricking the thread into a wait for itself, which could be easily
simulated by usermode without race.
Found by: Eric van Gyzen <eric@vangyzen.net>
In collaboration with: Eric van Gyzen <eric@vangyzen.net>
Tested by: pho
MFC after: 1 week
uc_busy value, and not its address [1].
Remove the single use of the macro, write KASSERT() explicitely in the
code of umtxq_sleep_pi().
Submitted by: Eric van Gyzen <eric@vangyzen.net> [1]
MFC after: 1 week
of fuword(9) and suword(9). This makes the functions type-compatible
with volatile objects and does not require devolatile force, e.g. in
kern_umtx.c.
Requested by: bde
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
Also fix some mishandling of suword(9) errors as errno, which resulted
in spurious ERESTART.
Sponsored by: The FreeBSD Foundation
Tested by: pho
MFC after: 3 weeks
in a separate word from the _count. This does not permit both items to
be updated atomically in a portable manner. As a result, sem_post()
must always perform a system call to safely clear _has_waiters.
This change removes the _has_waiters field and instead uses the high bit
of _count as the _has_waiters flag. A new umtx object type (_usem2) and
two new umtx operations are added (SEM_WAIT2 and SEM_WAKE2) to implement
these semantics. The older operations are still supported under the
COMPAT_FREEBSD9/10 options. The POSIX semaphore API in libc has
been updated to use the new implementation. Note that the new
implementation is not compatible with the previous implementation.
However, this only affects static binaries (which cannot be helped by
symbol versioning). Binaries using a dynamic libc will continue to work
fine. SEM_MAGIC has been bumped so that mismatched binaries will error
rather than corrupting a shared semaphore. In addition, a padding field
has been added to sem_t so that it remains the same size.
Differential Revision: https://reviews.freebsd.org/D961
Reported by: adrian
Reviewed by: kib, jilles (earlier version)
Sponsored by: Norse
doing suspend check. This restores the pre-r251684 behaviour, to
retry once after the signal is detected.
PR: kern/192918
Submitted by: Elliott Rabe, Dell Inc., Eric van Gyzen <eric@vangyzen.net>
Obtained from: Dell Inc.
MFC after: 1 week
- Retire long time unused (basically always unused) sys__umtx_lock()
and sys__umtx_unlock() syscalls
- struct umtx and their supporting definitions
- UMUTEX_ERROR_CHECK flag
- Retire UMTX_OP_LOCK/UMTX_OP_UNLOCK from _umtx_op() syscall
__FreeBSD_version is not bumped yet because it is expected that further
breakages to the umtx interface will follow up in the next days.
However there will be a final bump when necessary.
Sponsored by: EMC / Isilon storage division
Reviewed by: jhb
- When looping, check for the pending suspension. Otherwise, other
usermode thread which races with the looping one, could try to
prevent the process from stopping or exiting.
- Add missed checks for the faults from casuword*(). The code is
structured in a way which makes the loops exit if the specified
address is invalid, since both fuword() and casuword() return -1 on
the fault. But if the address is mapped readonly, the typical value
read by fuword() is different from -1, while casuword() returns -1.
Absent the checks for casuword() faults, this is interpreted as the
race with other thread and causes non-interruptible spinning in the
kernel.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Programs often do not expect an [EINTR] return from sem_wait() and POSIX
only allows it if the signal was installed without SA_RESTART. The timeout
in sem_timedwait() is absolute so it can be restarted normally.
The umtx call can be invoked with a relative timeout and in that case
[ERESTART] must be changed to [EINTR]. However, libc does not do this.
The old POSIX semaphore implementation did this correctly (before r249566),
unlike the new umtx one.
It may be desirable to avoid [EINTR] completely, which matches the pthread
functions and is explicitly permitted by POSIX. However, the kernel must
return [EINTR] at least for signals with SA_RESTART clear, otherwise pthread
cancellation will not abort a semaphore wait. In this commit, only restore
the 8.x behaviour which is also permitted by POSIX.
Discussed with: jhb
MFC after: 1 week
UMTX_PROFILING should really analyze the distribution of locks as they
index entries in the umtxq_chains hash-table.
However, the current implementation does add/dec the length counters
for *every* thread insert/removal, measuring at all really userland
contention and not the hash distribution.
Fix this by correctly add/dec the length counters in the points where
it is really needed.
Please note that this bug brought us questioning in the past the quality
of the umtx hash table distribution.
To date with all the benchmarks I could try I was not able to reproduce
any issue about the hash distribution on umtx.
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff, davide
MFC after: 2 weeks
- Use u_int values for length and max_length values
- Add a way to reset the max_length heuristic in order to have the
possibility to reuse the mechanism consecutively without rebooting
the machine
- Add a way to quick display top5 contented buckets in the system for
the max_length value.
This should give a quick overview on the quality of the hash table
distribution.
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff, davide
application destroys semaphore after sem_wait returns. Just enter
kernel to wake up sleeping threads, only update _has_waiters if
it is safe. While here, check if the value exceed SEM_VALUE_MAX and
return EOVERFLOW if this is true.
a mutex after a thread has unlocked it, it event writes data to the mutex
memory to clear contention bit, there is a race that other threads
can lock it and unlock it, then destroy it, so it should not write
data to the mutex memory if there isn't any waiter.
The new operation UMTX_OP_MUTEX_WAKE2 try to fix the problem. It
requires thread library to clear the lock word entirely, then
call the WAKE2 operation to check if there is any waiter in kernel,
and try to wake up a thread, if necessary, the contention bit is set again
by the operation. This also mitgates the chance that other threads find
the contention bit and try to enter kernel to compete with each other
to wake up sleeping thread, this is unnecessary. With this change, the
mutex owner is no longer holding the mutex until it reaches a point
where kernel umtx queue is locked, it releases the mutex as soon as
possible.
Performance is improved when the mutex is contensted heavily. On Intel
i3-2310M, the runtime of a benchmark program is reduced from 26.87 seconds
to 2.39 seconds, it even is better than UMTX_OP_MUTEX_WAKE which is
deprecated now. http://people.freebsd.org/~davidxu/bench/mutex_perf.c
according to POSIX document, the clock ID may be dynamically allocated,
it unlikely will be in 64K forever. To make it future compatible, we
pack all timeout information into a new structure called _umtx_time, and
use fourth argument as a size indication, a zero means it is old code
using timespec as timeout value, but the new structure also includes flags
and a clock ID, so the size argument is different than before, and it is
non-zero. With this change, it is possible that a thread can sleep
on any supported clock, though current kernel code does not have such a
POSIX clock driver system.
UMTX_OP_WAIT. Upper 16bits is enough to hold a clock id, and lower
16bits is used to pass flags. The change saves a clock_gettime() syscall
from libthr.
