This is a syntax error.
POSIX does not say explicitly whether defining a function with the same name
as a special builtin is allowed, but it does say that it is impossible to
call such a function.
A special builtin can still be overridden with an alias.
This commit is part of a set of changes that will ensure that when
something looks like a special builtin to the parser, it is one. (Not the
other way around, as it remains possible to call a special builtin named
by a variable or other substitution.)
Exp-run done by: pav (with some other sh(1) changes)
VLAN hardware tagging to make TSO work over VLAN. So if VLAN
hardware tagging is disabled explicitly clear TSO over VLAN. While
I'm here allow disabling VLAN TX checksum offloading.
Tested by: Liudas < liudasb <> centras dot lt >
MFC after: 10 days
Add some conservative checks on function names:
- Disallow expansions or quoting characters; these can only be called via
strange control characters
- Disallow '/'; these functions cannot be called anyway, as exec.c assumes
they are pathnames
- Make the CTL* bytes work properly in function names.
These are syntax errors.
POSIX does not require us to support more than names (letters, digits and
underscores, not starting with a digit), but I do not want to restrict it
that much at this time.
Exp-run done by: pav (with some other sh(1) changes)
initialize all the data. This is huge waste of time and resources if
there were no writes yet, as there is no real data to synchronize.
Optimize this by sending "virgin" argument to secondary, which gives it a hint
that synchronization is not needed.
In the common case (where noth nodes are configured at the same time) instead
of synchronizing everything, we don't synchronize at all.
MFC after: 1 week
This is how ksh93 treats ! within a pipeline and makes the ! in
a | ! b | c
negate the exit status of the pipeline, as if it were
a | { ! b | c; }
Side effect: something like
f() ! a
is now a syntax error, because a function definition takes a command,
not a pipeline.
Exp-run done by: pav (with some other sh(1) changes)
existing code caused problems with some SCSI controllers.
A new sysctl kern.cam.ada.spindown_shutdown has been added that controls
whether or not to spin-down disks when shutting down.
Spinning down the disks unloads/parks the heads - this is
much better than removing power when the disk is still
spinning because otherwise an Emergency Unload occurs which may cause damage
to the actuator.
PR: kern/140752
Submitted by: olli
Reviewed by: arundel
Discussed with: mav
MFC after: 2 weeks
converted to use the mii_phy_add_media()/mii_phy_setmedia() pair instead
of mii_add_media()/mii_anar() remove the latter.
- Declare mii_media mii_media_table static as it shouldn't be used outside
of mii_physubr.c.
MFC after: never
interface also has such connectors.
- In tl_attach() unify three different ways of obtaining the device and
vendor IDs and remove the now obsolete tl_dinfo from tl_softc.
- Given that tlphy(4) only handles the integrated PHYs of NICs driven by
tl(4) make it only probe on the latter.
- Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia().
- Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4)
by ignoring the native one by just comparing the device_t's directly rather
than the device name.
- Use mii_phy_add_media() instead of mii_add_media(). I'm not sure how
this driver actually managed to work before as mii_add_media() is
intended to be used to gether with mii_anar() while mii_phy_add_media()
is intended to be used with mii_phy_setmedia(), however this driver
mii_add_media() along with mii_phy_setmedia().
to use the generic hash32_buf() function. Although adding the
bytes seemed sufficient for UFS and ZFS, since most of the bytes
are the same for file handles on the same volume, this might not
be sufficient for other file systems. Use of a generic function
also seems preferable to one specific to NFSv4.
Suggested by: gleb.kurtsou at gmail.com
MFC after: 10 days
to BCM6906 A0/A2. This should fix a long standing BCM5906 A2 lockup
issues. Data sheet explicitly mentions BCM5906 A0, A1 and A2 use
de-pipelined mode on these revisions.
Special thanks to Buganini who tried all combinations of
experimental patches for more than 10 days.
Tested by: Buganini <buganini <> gmail dot com >
legacy and IPv6 route destination address.
Previously in case of IPv6, there was a memory overwrite due to not enough
space for the IPv6 address.
PR: kern/122565
MFC After: 2 weeks
the association notification), the included information though always
contains an elem block with an odd number of bytes. We handle the last
byte as if it might contain a whole elem block, this of course is not
true as one byte is not enough to hold a block, we therefore discard the
complete frame. The solution here is to subtract one from the actual
notification length, this is also what the Linux driver does. With this
change the frames ends exactly where the last elem block ends.
This commit also reverts r214160 which is no longer required and now even
wrong.
MFC after: 1 week
information that device is already suspended or that device is using
one-time key and suspend is not supported.
- 'geli suspend -a' silently skips devices that use one-time key, this is fine,
but because we log which device were suspended on the console, log also which
devices were skipped.
server so that it will work better for non-UFS file systems.
The new function simply sums the bytes of the fh_fid field
of fhandle_t.
MFC after: 10 days
auto-negotiation results in half-duplex operation, excess collision
on the ethernet link may cause internal chip delays that may result
in subsequent valid frames being dropped due to insufficient
receive buffer resources. The workaround is to choose de-pipeline
method as a flow control decision for SDI. De-pipeline method
allows only 1 data in TxMbuf at a time such that a request to RDMA
from SDI is made only when TxMbuf is empty. Thanks for david for
providing detailed errata information.
