interrupt-driven configuration handlers to complete, print out a
diagnostic message every 60 second indicating which handlers are
still running. Do this at most 5 times per run so as to avoid
scrolling out any useful information from the kernel message
buffer.
The interval of 60 seconds was selected based on a best guess as
to the nature of "long enough" and may want to be tuned higher
or lower depending on real-world tolerances.
MFC after: 3 days
Discussed with: scottl
for completion in run_interrupt_driven_config_hooks(). This is
helpful when trying to figure out which device drivers have gone
into la-la land during boot-time autoconfiguration.
MFC after: 3 days
- When a tick occurs on a cpu, iterate from cs_softticks until ticks.
The per-cpu tick processing happens asynchronously with the actual
adjustment of the 'ticks' variable. Sometimes the results may
be visible before the local call and sometimes after. Previously this
could cause a one tick window where we didn't evaluate the bucket.
- In softclock fetch curticks before incrementing cc_softticks so we
don't skip insertions which were made for the current time.
Sponsored by: Nokia
sched_tick() to prevent multiple increments for one tick. This pushes
the value out of range and breaks priority calculation.
Reviewed by: kib
Found by: pho/nokia
Sponsored by: Nokia
MFC after: 3 days
The segfaults when using SSP seem to be a gcc bug, a patch is available
in the gcc bugzilla, and will be imported once it's committed
into the official gcc tree.
the chunk map instead of red-black trees where possible. Remove the
red-black trees and node objects that are obsoleted by this change. The
net result is a ~1-2% memory savings, and a substantial allocation speed
improvement.
if we're reducing a rule that has an empty
right hand side and the yacc stackpointer is pointing at the very
end of the allocated stack, we end up accessing the stack out of
bounds by the implicit $$ = $1 action
Obtained from: OpenBSD
information from rip_input() to rip_append(). Instead, pass the source
address for an IP datagram to rip_append() using a stack-allocated
sockaddr_in, similar to udp_input() and udp_append().
Prior to the move to rwlocks for inpcbinfo, this was not a problem, as
use of the global was synchronized using the ripcbinfo mutex, but with
read-locking there is the potential for a race during concurrent
receive.
This problem is not present in the IPv6 raw IP socket code, which
already used a stack variable for the address.
Spotted by: mav
MFC after: 1 week (before inpcbinfo rwlock changes)
1. architecture-specific files
2. long double format-specific files
3. bsdsrc
4. src
5. man
The original order was virtually the opposite of this.
This should not cause any functional changes at this time. The
difference is only significant when one wants to override, say, a
generic foo.c with a more specialized foo.c (as opposed to foo.S).
and handle NIC hardware watchdog resets.
- remove buggy code at the top of mxge_tick() which tried
to detect a race which is already detected in the kernel's
callout code.
- move callout_stop() and callout_reset() into mxge_close()
mxge_open() rather than doing the callout manipulation
all over the place.
- use callout_drain(), rather than callout_stop() to prevent
a potential race between mxge_tick() and mxge_detach()
which could lead to softclock using a destroyed mutex
- restructure the mxge_tick() and mxge_watchdog_reset()
routines to avoid resetting a callout, and then
immediately stopping it if the watchdog reset routine
is called, and fails.
- enable the driver to handle NIC hardware watchdog
resets by restoring the NIC's PCI config space, which is
lost when the NIC hardware watchdog triggers.
Reviewed by: jhb (previus version)
sanity check by invoking "pwd_mkdb -C". However, if this failed it
silently returned success. Fix this so it fails the update operation
instead.
MFC after: 1 week
to allow them to do a "clean" shutdown.
I purposely avoided making changes to network-related stuff since the
system shutting down is pretty conclusive, and there may be complicated
dependencies on the network that I would rather not try to unravel.
I also skipped kerberos-related stuff for the reasons above, and
because I have no way to test it.
The tcsetattr() routine already converts the TCSA* arguments to their
respective TIOCSETA* ioctl's in the C library. There is no need to have
these definitions inside the kernel.
Approved by: philip (mentor, implicit)
I think one of the reasons why we have so many conflicts in the TTY
ioctl category, is because the ioctl's aren't ordered logically. This
commit only sorts them by number. The comments may still be inaccurate.
Approved by: philip (mentor)
When I ported most applications away from <sgtty.h>, I noticed none of
them were actually using these definitions. I kept them in place,
because I didn't want to touch tools like pstat(8) and stty(1).
In preparation for the MPSAFE TTY layer, remove these definitions. This
doesn't have any impact with respect to binary compatibility (see
tty_conf.c).
We couldn now add an #error to <sys/ioctl_compat.h> when included
outside the kernel. Unfortunately, kdump's mkioctls includes this file
unconditionally.
Approved by: philip (mentor)
vr(4) overhauling(r177050).
It seems that filtering multicast addresses with multicast CAM
entries require accessing 'CAM enable bit' for each CAM entry.
Subsequent accessing multicast CAM control register without
toggling the 'CAM enable bit' seem to no effects.
In order to fix that separate CAM setup from CAM mask configuration
and CAM entry modification. While I'm here add VLAN CAM filtering
feature which will be enabled in future(FreeBSD now can receive
VLAN id insertion/removal event from vlan(4) on the fly).
For VT6105M hardware, explicitly disable VLAN hardware tag
insertion/stripping and enable VLAN CAM filtering for VLAN id 0.
This shall make non-VLAN frames set VR_RXSTAT_VIDHIT bit in Rx
status word.
Added multicast/VLAN CAM address definition to header file.
PR: kern/125010, kern/125024
MFC after: 1 week
years. All datasheet I have indicates the bit 15 is the
VR_RXSTAT_RX_OK. The bit 14 is reserved for all Rhine family
except VT6105M. VT6105M uses that bit to indicate a VLAN frame
with matching CAM VLAN id.
Use the VR_RXSTAT_RX_OK instead of VR_RXSTAT_RXERR when vr(4)
checks the validity of received frame.
This should fix occasional dropping frames on VT6105M.
Tested by: Goran Lowkrantz ( goran.lowkrantz at ismobile dot com )
MFC after: 1 week
