ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
in some code from C. Stone to parse the lease information. This is still
a WIP and this commit is largely intended to allow others to sync up; the
dhclient code still only works when doing dhcp configuration post-install
and requires a bit more work on the boot floppy before it will truly
work in the minimal bootstrapping role.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
on CDs and FTP sites.
o Collapse some redundant code.
o Fix typo'd menu.
o Restrict searches properly to packages rather than categories.
o Small tweaks to signal handling.
All RELENG_3 candidates.
feature of packages now so that no version info is embedded.
o Add a default X desktop menu offering afterstep, enlightenment, KDE, GNOME
and Windowmaker desktops instead of the boring twm(1) based one if the
user so chooses. This will require a little testing.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
to now detect that CD you just remembered to put in the drive or that
pccard NIC that you've inserted (anybody can put pccardd in an mfsroot image
now you know.. :)
Requested by: Annelise Anderson <andrsn@andrsn.Stanford.EDU>
orthogonal to the other entries).
Clean up X selection code a bit.
Choose proper architecture subdirectories on mirror sites now that we've
gone fully to the new multi-arch directory scheme.
Now we know which variables are internal and which need to be
backed to /etc/rc.conf.site. rc.conf is not touched now.
Also kget kernel change information back properly and set up a loader.rc
file to use it.
on the ASIX AX88140A chip. Update /sys/conf/files, RELNOTES.TXT,
/sys/i388/i386/userconfig.c, sysinstall/devices.c, GENERIC and LINT
accordingly.
For now, the only board that I know of that uses this chip is the
Alfa Inc. GFC2204. (Its predecessor, the GFC2202, was a DEC tulip card.)
Thanks again to Ulf for obtaining the board for me. If anyone runs
across another, please feel free to update the man page and/or the
release notes. (The same applies for the other drivers.)
FreeBSD should now have support for all of the DEC tulip workalike
chipsets currently on the market (Macronix, Lite-On, Winbond, ASIX).
And unless I'm mistaken, it should also have support for all PCI fast
ethernet chipsets in general (except maybe the SMC FEAST chip, which
nobody seems to ever use, including SMC). Now if only we could convince
3Com, Intel or whoever to cough up some documentation for gigabit
ethernet hardware.
Also updated RELNOTEX.TXT to mention that the SVEC PN102TX is supported
by the Macronix driver (assuming you actually have an SVEC PN102TX with
a Macronix chip on it; I tried to order a PN102TX once and got a box
labeled 'Hawking Technology PN102TX' that had a VIA Rhine board inside
it).
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
o Move fixups into extraction routine so all consumers don't have to duplicate
the right behavior.
o Make some things more orthogonal (just for asthetics sake)
o Add option to go back and do it again if XF86Setup fails (possibly with
a different setup - this one has always annoyed me).
RealTek 8129/8139 chipset like I've been threatening. Update kernel
configs, userconfig.c, relnotes and sysinstall. No man page yet;
comming soon.
I consider this driver stable enough that I want to give it some
exposure in -current.
various ports don't complain about it. It also requires that the pkg
registration bits be stick into the Xbin tarball so that they'll be
present in /usr/X11R6/lib/X11/pkgreg.tar.gz. The registration tarball
is removed upon first use to prevent it later spamming a genuine build
from ports if inadvertently extracted again.
apparently, unlike the IDE or SCSI CDROM drivers, this is magically
special-cased for audio CDs. This also might explain what happened
with scd (Sony) CDs also since I made the same change there. A follow-up
commit will fix that. Thanks, Dave!
PR: 6576
Submitted by: Dave Marquardt <marquard@zilker.net>
the device is enabled by default in the GENERIC kernel.
- Kill the mouse daemon, if any, when the user wants to disable it.
- Minor update on mouse menus.
again.
2. Don't create slice entries when running multi-user; it adds far too
much to sysinstall's startup time. User is expected to have correct
slice entries after system is installed.
PRT servers since the extra PC98 servers have eaten all my flag bits.
Time to redo the way distribution masks are calculated, definitely, but
for now I guess people can always install those two components by hand
if they really want them.
probed in sysinstall. Rather than make template devices and use up lots
of inodes, also restricting the number of devices that can be dealt with,
mknod all necessary devices as necessary using built-in information.
This removes a number of constraints on the number and type of devices
that sysinstall can see.
Now you can use one without entering the other and it will DTRT.
These changes just allowed me to do the most straight-forward new disk
installation I've ever managed with sysinstall.
setup dialog from scripts is more controllable. No more biasing off of
hostname (which is now non-optional in the non-netInteractive case).
Requested by: pst
lots of disks from sysinstall. Yay! Please test this as much as
possible with any 3.0 SNAP later than 970910 (I.E. tomorrow's snap),
especially those of you with larger disk farms.
Submitted by: Ed Gold <vegold01@starbase.spd.louisville.edu>
so you don't need to re-enter it for each and every filesystem. Heads up!
This change is incompatible with the previous scripting format,
so those folks (all 2 of you) using config files should take a look
at the changes to the sample install.cfg file for the diskLabelEditor's
new calling syntax.
Finally write a man page for this thing, documenting all of the above
and more. I can't drive a stake through this thing's heart without
properly documenting it first, so please consider this step #1 in that
process (to be honest, sysinstall will also live on for some time in
the 2.2. branch since it's unlikely that the new install tools will ever
make it over there - they're strictly 3.0 material).
1. Detecting the split /dev/ttyv0 / /dev/console case, e.g. you've
booted with the -h flag and you have a VGA card also.
2. Adding an extra "menu" for selecting terminal type and adding ANSI
to the list of compiled-in terms.
3. Opening the proper file descriptors before disowning ourselves.
Requested by: pst
those ideas that, like the Apache server setup, was well-intentioned
but doomed to fail in the face of change. That and the fact that it
shouldn't be part of the installation tool, it should be part of the
post-installation setup tool (which we need to write). Combining the
two utilities into one utility was my first conceptual mistake.
Apologies also to Coranth Gryphon, who worked hard on the Apache
and Samba server setup code. These features were quite useful
for awhile, if that's any consolation, I just simply had the wrong
ideas about where to put them. :-(
Add a system command to script mechanism (so you can call things like
tzsetup from scripts).
Add noError variable for causing script errors to be ignored.
sysinstall about the dangerously dedicated message, and other
variables to allow pre-configuring the distribution sets.
Still todo: add a variable to define an initial set of packages that
should be loaded.
Reviewed by: jkh
2. Back out my change to ask about UTC/Localtime here. This *really* needs
to be done in tzsetup instead since putting it here only handles about
1/4 of the places where it needs to be.
Now that this is becoming (dare I even say it?) more useful for
post-configuration, no longer leave sysinstall.debug files around
by default. Only do this if environment variable SYSINSTALL_DEBUG
is set.
so that we're more useful in multi-user mode. This is still not
100%, but it pulls in a lot more than it used to. Some of the "composite"
variables in /etc/sysconfig are going to take more work.
o Always write /etc/resolv.conf and /etc/hosts if it makes sense to do
so.
o Reset media properly when reselecting. Longstanding bogon.
o Pull SIGPIPE handling out of package.c; I'm actually hoping to handle
this differently shortly.
o Fix bug where cancel in TCP setup dialog still checked data fields.
I think this closes a PR, but I will have to go look.
at the time, but on further reflection..." bucket with these changes.
1. Checking the media before frobbing the disks was a fine idea, and
I wish it could have worked, but that leads to a rather difficult
situation when you need to mount the media someplace and you're about
to:
a) Chroot away from your present root.
b) Newfs the root to be.
You're basically screwed since there's no place to stick the mount
point where it will be found following the newfs/chroot (and eliminating
the chroot in favor of just using the "root bias" feature would work
great for the distributions but not the pkg_add calls done by the
package installer).
2. Automatic timeout handling. I don't know why, but alarm() frequently
returns no residual even when the alarm didn't go off, which defies
the man page but hey, since when was that so unusual? Take out timeouts
but retain the code which temporarily replaces the SIGINT handler in
favor of a more media-specific handler. This way, at least, if it's hanging
you can at least whap it. I think the timeout code would have been losing
over *really slow* links anyway, so it's probably best that it go.
This should fix NFS, tape & CDROM installs again (serves me right for getting
complacent and using just the FTP installs in my testing).
more consistant in our use of the terms for differentiation between PC
partitions and traditional BSD partitions.
Submitted-By: obrien@cs.ucdavis.edu (David O'Brien)
section was a good thing, since it made it possible to detect media problems
*before* the installation started, but it also caused various things to
be mounted BEFORE the chroot() call, which definitely messes things up.
Fix this by detecting the pre-chroot() case and mounting into a subdir.
bogus path and FTP I/O errors much earlier, offer retry possibilities
at steps along the way so you don't have to resume from the very beginning
again on a hard error.
1. Bus mouse selection didn't show up properly in mouse menu.
2. U&G management screen didn't respect cancel properly.
3. Novice not prompted to add users or set root password during installation.
4. Username length changes screw up user management form.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
Use consistent spelling throughout.
Remove unmount in fixit_common() since that's bogus in the CDROM case and
properly "shut down" the media device instead.
