Files listed in 'CONFS' are not properly included in new
installations (missing from base.txz), for reasons I still
do not fully understand.
This reverts the change excluding /etc/ppp/ppp.conf from
a new installation. /etc/dma/dma.conf is also affected,
but requires a different solution, still being investigated.
Reported by: Ben Woods
Sponsored by: The FreeBSD Foundation
No functional change, although _thread_printf() may be slightly less functional
or render some values differently from libc snprintf(3). No ABI change.
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D6672
Do not set HWRTSEN bit when CTS-to-self is used; CTS2SELF bit triggers
CTS frame transmission by itself (and it does not work when HWRTSEN bit
is set).
Tested with:
* RTL8188CUS, HOSTAP mode (11g)
* RTL8188EU, STA mode (11g)
If tzsetup UTC is run then it successfully configured the system for UTC
including installing /etc/localtime however if the user ran just tzsetup
for interactive configuration and select UTC no /etc/localtime was installed
which resulted in failures for utilities which require said file.
Change set_zone_utc to call install_zoneinfo("UTC") to ensure that
/etc/localtime is created for interactive UTC selection.
Users who have previously run tzsetup in interactive mode and select UTC
can install the missing /etc/localtime by running tzsetup -r.
Also correct static miss-match for set_zone_utc.
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Multiplay
Receive all beacons in HOSTAP mode; they will give more information about
present non-ERP / legacy BSSs (used to choose protection mode).
Tested with RTL8188CUS (HOSTAP, urtwn) + RTL8821AU (HOSTAP, 11b mode).
This simplifies setting an initial interrupt moderation value, and
avoids most calls to evx_ev_qmoderate from contexts where MCDI is
not allowed (MCDI is need for an EVQ timer workaround in a later patch).
Submitted by: Andy Moreton <amoreton at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6673
by default. This is a workaround for a too simplistic ICL module
choosing mechanism. To use it, specify offload in ctl.conf
or iscsi.conf.
This fixes a problem where "kldload cxgbei" wedges the iSCSI stack,
if you don't have a Chelsio card installed, or the endpoints of the
iSCSI session are not reachable through addresses configured
on that interface.
Reviewed by: np@
MFC after: 1 month
specific order. VNET_SYSUNINITs however are doing exactly that.
Thus remove the VIMAGE conditional field from the domain(9) protosw
structure and replace it with VNET_SYSUNINITs.
This also allows us to change some order and to make the teardown functions
file local static.
Also convert divert(4) as it uses the same mechanism ip(4) and ip6(4) use
internally.
Slightly reshuffle the SI_SUB_* fields in kernel.h and add a new ones, e.g.,
for pfil consumers (firewalls), partially for this commit and for others
to come.
Reviewed by: gnn, tuexen (sctp), jhb (kernel.h)
Obtained from: projects/vnet
MFC after: 2 weeks
X-MFC: do not remove pr_destroy
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6652
It seems that all versions of POSIX that I could find require that
<sys/resource.h> defines id_t. Define it together with rlim_t. While
there, move these typedefs closer to the top of the header file, right
after the includes, which we do in most other header files.
on performance, especially with SD cards on certain SoCs.
Requested by: trasz
Discussed with: ian, kientzle
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
These are apparently conditional on there being a shared PA/LNA, which
at least on AR9462/QCA9535 devices I have isn't a thing.
I'm .. not yet sure which devices it /is/ a thing, so I'll come back
to that.
Tested:
* QCA9565 STA + bluetooth
Obtained from: Linux ath9k
* Add extra debugging - the weights debugging is really useful to ensure
things are programmed into the wlan coexistence table. The weights are
what traffic priority each of the various modes get (tx, tx-high-priority,
rx-beacon, etc) if they're all zero, things work very poorly.
* Add in coex init routines from ath9k for AR9462 and QCA9565 1ANT and 2ANT.
This control things like beacon stomping, ACK handling, antennas, PA/LNA
shared, etc.
* Some ancillary bits.
TODO:
* There's some conditional stuff around MCI_ANT_ARCH_PA_LNA_SHARED() in ath9k
which doesn't always enable force-on LNA. That'll have to be examined
and merged in as appropriate.
Obtained from: linux ath9k
Notably, this also sets AR_BTCOEX_WL_LNADIV to FORCE_ON, so LNA diversity
is always enabled and under control of the wifi chip.
Tested:
* QCA9565, STA + bluetooth mode
Obtained from: Linux ath9k
This configures the LNA antenna diversity control, which should be on
if wlan owns the LNA for bluetooth coexistence. Otherwise, make sure
it's off.
I think this is eventually intended to allow 1-antenna bluetooth +
wifi setups for QCA9565, but I'm not sure where that's actually configured
in ath9k.
Obtained from: Linux ath9k
mkimg(1) uses a swap file to back input file chunks. When the output file
is being written out, blocks of the swap file are mapped and their contents
copied. This causes the backing VM pages to enter the active queue, and when
the output file is large relative to system memory (as is generally the
case), can result in a shortfall of inactive memory. This causes the
pagedaemon to aggressively scan the active queue and swap out process
memory in an attempt to meet the shortfall. Because mkimg's input files
are typically the intermediate result of some build process, there's no
need to push them all through the active queue. Use madvise(2) to indicate
that the backing pages may be reclaimed in preference to active pages. In
the case of the swap file, these pages will be freed as soon as mkimg
exits anyway.
When using mkimg on a desktop-class system with large amounts of dirty
process memory, this change substantially improves mkimg runtime and
reduces swap usage.
Reviewed by: marcel
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6654
lib/libdevdctl/consumer.cc
In Consumer::DisconnectFromDevd, don't close the socket if it's
already closed.
cddl/usr.sbin/zfsd/case_file.cc
lib/libdevdctl/consumer.h
Delete dead code leftover from before devd(8) gained SOCK_SEQPACKET
support
Reported by: Coverity
CID: 1356155, 1356169
Sponsored by: Spectra Logic Corp
Since META_MODE is being sold and used as a working incremental build, it won't
make much sense if filemon data is excluded. There is no way to recover
from that in a subsequent build.
Sponsored by: EMC / Isilon Storage Division
