these were cosmetic. However, at least two of these changes fix bugs
where a (fake) pointer to a RX descriptor was added to the physical
memory start address with the cast in the wrong place resulting in
rxdesc[pmem_start] instead of (uintptr_t)rxdesc + pmem_start.
of the original AIO request: save and restore the active thread credential
as well as using the file credential, since MAC (and some other bits of
the system) rely on the thread credential instead of/as well as the
file credential. In brief: cache td->td_ucred when the AIO operation
is queued, temporarily set and restore the kernel thread credential,
and release the credential when done. Similar to ktrace credential
management.
Reviewed by: alc
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
take advantage of the fact that the vm object's list of pages is
now ordered to reduce the overhead of finding the desired set of
pages to be mapped. (See revision 1.215 of vm/vm_page.c.)
1. At least some Netra t1 models have PCI buses with no associated
interrupt map, but obviously expect the PCI swizzle to be done with
the interrupt number from the higher level as intpin. In this case,
the mapping also needs to continue at parent bus nodes.
To handle that, add a quirk table based on the "name" property of
the root node to avoid breaking other boxen. This property is now
retrieved and printed at boot.
2. On SPARCengine Ultra AX machines, interrupt numbers are not mapped
at all, and full interrupt numbers (not just INOs) are given in
the interrupt properties. This is more or less cosmetical; the
PCI interrupt numbers would be wrong, but the psycho resource
allocation method would pass the right numbers on anyway.
Tested by: mux (1), Maxim Mazurok <maxim@km.ua> (2)
just limited to the DEVICE_POLLING case. This removes the FXP_RFA_RNRMARK
hack, and replaces it with a softc flag that is used to record when
the handling of a no-resource condition was deferred due to running
out of DEVICE_POLLING cycles. This was tested on -stable, but the
code is essentially the same as in -current. It should only affect
the case where DEVICE_POLLING is defined.
The details of the mechanism behind the crashes are still uncertain
but the most likely cause seems to be some kind of hardware confusion
when the no-resource recovery code is accidentally invoked while
the receiver is still active. This could have happened if the
hardware left the 0x4000 bit of the RFA status word set. The comments
in the commit log for revision 1.142 stating that the driver could
clash with the hardware writing to this status word were not correct.
Tested by: Guy Helmer <ghelmer@palisadesys.com>
to use the same start condition as the i386 version. However, since
Alpha's only have one fake "slice" from sysinstall's perspective we don't
need to use a loop, but can just write out the BSD label in the first
fake "slice".
remove global variable in_vm86call, set vm86 calling flag in PCB flags.
2.Fix vm86 BIOS calling preempted problem by changing vm86_lock mutex type
from MTX_DEF to MTX_SPIN. vm86pcb is not remembered in thread struct,
when the thread calling vm86 BIOS is preempted by interrupt thread,
and later switching back to the thread would cause incorrect context be
loaded into CPU registers, this leads to kernel crash.
argument is an expression you can end up casting part of it to void *.
This resulted in bogus warnings about pointer arith using void *'s for
the ep(4) driver.
from being MI in any fashion. It currently "assumes" that it can get
a kernel virtual address for a phyiscal address by adding KERNBASE to the
physical address. It also tries to read values out of a the PC BIOS on
all archs. It also uses "manual" inb() and outb()'s to talk to the mcclock
device which just happens to be at that location on both i386 and alpha.
This driver should likely be i386-only.
