on multiple different audit pipes. The old method used cv_signal()
which would result in only one thread being woken up after we
appended a record to it's queue. This resulted in un-timely wake-ups
when processing audit records real-time.
- Assign PSOCK priority to threads that have been sleeping on a read(2).
This is the same priority threads are woken up with when they select(2)
or poll(2). This yields fairness between various forms of sleep on
the audit pipes.
Obtained from: TrustedBSD Project
Discussed with: rwatson
MFC after: 1 week
This fixes the process portion of the bpf(4) stats if the peer forks
into the background after it's opened the descriptor. This bug
results in the following behavior for netstat -B:
# netstat -B
Pid Netif Flags Recv Drop Match Sblen Hblen Command
netstat: kern.proc.pid failed: No such process
78023 em0 p--s-- 2237404 43119 2237404 13986 0 ??????
MFC after: 1 week
- Add proper scanning support rather than letting the firmware grab the first
access point
- Overhaul state changes
- Use macros for locking and provide _locked() versions of some functions
- Increase debugging output
- Use a callout rather than the old watchdog interface
- Improve style, function names and defines
- Add WPA (TKIP) support
Based heavily on a patchset provided by Sam Leffler.
VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
1. The locking was changed to shared but roundrobin mode still updated a
pointer in the softc with the next tx interface to use. This will panic
under high load. Change this to an atomically incremented sequence number in
order to choose the tx port in round robin.
2. IFQ_HANDOFF will free the mbuf if the queue is full, this will then be freed
again by lagg_start() and panic. Reorganised the error handling and freeing
to fix this.
MFC after: 3 days
SAS-enabled cards. It also makes the driver MPSAFE, eliminating some
problems that resulted from CAM becoming MPSAFE. Many thanks to 3Ware/AMCC
for continuing to support FreeBSD.
Submitted by: Manjunath Ranganathaiah
Approved by: re
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
fixes a bug on UP machines with SMP kernels where the idle thread
constantly switches after trying to steal work from the local cpu.
- Make the idle stealing code more robust against self selection.
- Prefer to steal from the cpu with the highest load that has at least one
transferable thread. Before we selected the cpu with the highest
transferable count which excludes bound threads.
Collaborated with: csjp
Approved by: re
to simply switch rather than lowering priority and switching. This allows
threads of equal priority to run but not lesser priority.
Discussed with: davidxu
Reported by: NIIMI Satoshi <sa2c@sa2c.net>
Approved by: re
critical_exit() owepreempt check. ULE will always use owepreempt to
preempt the idle thread. This change does not effect 4BSD since it will
never set owepreempt without PREEMPTION enabled.
- Remove some unused code from choosethread().
Discussed with: jhb
Approved by: re
it must first ensure that the page is no longer mapped. This is
trivially accomplished by calling pmap_remove_all() a little earlier
in vm_page_cache(). While I'm in the neighborbood, make a related
panic message a little more useful.
Approved by: re (kensmith)
Reported by: Peter Holm and Konstantin Belousov
Reviewed by: Konstantin Belousov
a consequence of sparc64/sparc64/vm_machdep.c revision 1.76. It occurs
when uma_small_free() frees a page. The solution has two parts: (1) Mark
pages allocated with VM_ALLOC_NOOBJ as PG_UNMANAGED. (2) Defer the lock
assertion in pmap_page_is_mapped() until after PG_UNMANAGED is tested.
This is safe because both PG_UNMANAGED and PG_FICTITIOUS are immutable
flags, i.e., they do not change state between the time that a page is
allocated and freed.
Approved by: re (kensmith)
PR: 116794
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received data after socket was closed, sending RST and removing tcpcb
So that it also includes how many bytes of data were received. It now looks
like this:
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received X bytes of data after socket was closed, sending RST and removing tcpcb
Approved by: re (gnn)
not being independently freeable. This allows one to embed an mbuf in
the cluster itself. This confers the benefits of the packet zone on
all cluster sizes. Embedded mbufs currently suffer from the same
limitation that packet zone mbufs do in that one cannot disconnect
them and pass them around independently of the cluster. It would
likely be possible to eliminate this limitation in the future by
adding a second reference for the mbuf itself.
Approved by: re(gnn)
problems with the syncache, it produces a lot of console noise and has led
to quite a few false positive bug reports. It can be selectively
re-enabled when debugging specific problems by frobbing the same sysctl.
Discussed with: silby
Approved by: re (gnn)
directory itself (rather than any of its contents) is visible to the
current thread.
MFC after: 1 week
PR: kern/90063
Submitted by: john of 8192.net
Approved by: re (kensmith)
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
UDMA modes.
Please notice that Soekris NET5501 bios versions before 1.32f has a bug
that prevents this from working.
Approved by: re (gnn)
MFC: 2 weeks
Before that fix, it was possible for the function to fail if number
of sharers changes between 'x = sx->sx_lock' step and atomic_cmpset_acq_ptr()
call.
This fixes ZFS problem when ZFS returns strange EIO errors under load.
In ZFS there is a code that depends on the fact that sx_try_slock() can
only fail if there is an exclusive owner.
Discussed with: attilio
Reviewed by: jhb
Approved by: re (kensmith)
after the switch leads to a race where the outgoing thread still owns
the local queue lock while another cpu may switch it in. This race
is only possible on machines where cpu_switch can take significantly
longer on different cpus which in practice means HTT machines with
unfair thread scheduling algorithms.
Found by: kris (of course)
Approved by: re
starvation caused by unbalanced interrupt loads.
- Change the rebalancer to work on stathz ticks but retain randomization.
- Simplify locking in tdq_idled() to use the tdq_lock_pair() rather than
complex sequences of locks to avoid deadlock.
Reported by: kris
Approved by: re
