aic7xxx_pci.c:
Enable board generation of interrupts only once our handler is
in place and all other setup has occurred.
aic7xxx.c:
More conversion of data types to ahc_* names. tmode_tstate and
tmode_lstate are the latest victims.
Clean up the check condition path by branching early rather
than indenting a giant block of code.
Add support for target mode initiated sync negotiation.
The code has been tested by forcing the feature on for
all devices, but for the moment is left inaccesible until
a decent mechanism for controlling the behavior is complete.
Implementing this feature required the removal of the
old "target message request" mechanism. The old method
required setting one of the 16 bit fields to initiate
negotiation with a particular target. This had the nice
effect of being easy to change the request and have it
effect the next command. We now set the MK_MESSAGE bit
on any new command when negotiation is required. When
the negotiation is successful, we walk through and clean
up the bit on any pending commands. Since we have to walk
the commands to reset the SCSI syncrate values so no additional
work is required. The only drawback of this approach is that
the negotiation is deferred until the next command is queued to
the controller. On the plus side, we regain two bytes of
sequencer scratch ram and 6 sequencer instructions.
When cleaning up a target mode instance, never remove the
"master" target mode state object. The master contains
all of the saved SEEPROM settings that control things like
transfer negotiations. This data will be cloned as the
defaults if a target mode instance is re-instantiated.
Correct a bug in ahc_set_width(). We neglected to update
the pending scbs to reflect the new parameters. Since
wide negotiation is almost always followed by sync
negotiation it is doubtful that this had any real
effect.
When in the target role, don't complain about
"Target Initiated" negotiation requests when an initiator
negotiates with us.
Defer enabling board interrupts until after ahc_intr_enable()
is called.
Pull all info that used to be in ahc_timeout for the FreeBSD
OSM into ahc_dump_card_state(). This info should be printed
out on all platforms.
aic7xxx.h:
Add the SCB_AUTO_NEGOITATE scb flag. This allows us to
discern the reason the MK_MESSAGE flag is set in the hscb
control byte. We only want to clear MK_MESSAGE in
ahc_update_pending_scbs() if the MK_MESSAGE was set due
to an auto transfer negotiation.
Add the auto_negotiate bitfield for each tstate so that
behavior can be controlled for each of our enabled SCSI
IDs.
Use a bus interrupt handler vector in our softc rather
than hard coding the PCI interrupt handler. This makes
it easier to build the different bus attachments to
the aic7xxx driver as modules.
aic7xxx.reg:
Remove the TARGET_MSG_REQUEST definition for sequencer ram.
aic7xxx.seq:
Fix a few target mode bugs:
o If MK_MESSAGE is set in an SCB, transition to
message in phase and notify the kernel so that
message delivery can occur. This is currently
only used for target mode initiated transfer
negotiation.
o Allow a continue target I/O to compile without
executing a status phase or disconnecting. If
we have not been granted the disconnect privledge
but this transfer is larger than MAXPHYS, it may
take several CTIOs to get the job done.
Remove the tests of the TARGET_MSG_REQUEST field in scratch ram.
aic7xxx_freebsd.c:
Add support for CTIOs that don't disconnect. We now defer
the clearing of our pending target state until we see a
CTIO for that device that has completed sucessfully.
Be sure to return early if we are in a target only role
and see an initiator only CCB type in our action routine.
If a CTIO has the CAM_DIS_DISCONNECT flag set, propogate
this flag to the SCB. This flag has no effect if we've
been asked to deliver status as well. We will complete
the command and release the bus in that case.
Handle the new auto_negotiate field in the tstate correctly.
Make sure that SCBs for "immediate" (i.e. to continue a non
disconnected transaction) CTIO requests get a proper mapping
in the SCB lookup table. Without this, we'll complain when
the transaction completes.
Update ahc_timeout() to reflect the changes to ahc_dump_card_state().
aic7xxx_inline.h:
Use ahc->bus_intr rather than ahc_pci_intr.
I've left out a couple of unused args between internal functions.
Use MAXPATHLEN, not MAXPATHLEN + 1 in a couple of places.
Pass a pointer to the end of the target filename space.
two subject ucreds. Unlike p_cansee(), u_cansee() doesn't have
process lock requirements, only valid ucred reference requirements,
so is prefered as process locking improves. For now, back p_cansee()
into u_cansee(), but eventually p_cansee() will go away.
Reviewed by: jhb, tmm
Obtained from: TrustedBSD Project
Note that "right" in this case is not universally recognized, but
NTP-practittioners as opposed to theoretians generally agree that
getting "inside the window" using ntpdate is TRTTD on PC hardware.
PR: 25514
Submitted by: Chris Johnson <cjohnson-pr@palomine.net>
locks were held, we could be preempted and switch CPU's in between the time
that we set a variable to the list of spin locks on our CPU and the time
that we checked that variable to ensure no spinlocks were held while
grabbing a sleep lock. Losing the race resulted in checking some other
CPU's spin lock list and bogusly panicing.
* Initialize the "struct sockaddr_dl sdl" correctly in vlan_setmulti().
PR: kern/22181
* The driver used to call malloc(..., M_NOWAIT), but to not check the
return value. Change malloc(..., M_NOWAIT) to malloc(..., M_WAITOK)
because the corresponding part of code is called from the upper
half of the kernel only.
PR: kern/22181
* Make sure a parent interface is up and running before invoking
its if_start() routine in order to avoid system panic.
PR: kern/22179 kern/24741 i386/25478
* Do not copy all the flags from a parent mindlessly.
PR: kern/22179
* Do not call if_down() on a parent interface if it's already down.
Call if_down() at splimp because if_down() needs that.
PR: kern/22179
Reviewed by: wollman
Change code from PRC_UNREACH_ADMIN_PROHIB to PRC_UNREACH_PORT for
ICMP_UNREACH_PROTOCOL and ICMP_UNREACH_PORT
And let TCP treat PRC_UNREACH_PORT like PRC_UNREACH_ADMIN_PROHIB
This should fix the case where port unreachables for udp returned
ENETRESET instead of ECONNREFUSED
Problem found by: Bill Fenner <fenner@research.att.com>
Reviewed by: jlemon
decode the BIOS and firmware version and announce the board as HP NetRaid.
This has been tested with a NetRaid 3si controller, the BIOS/firmware
printout should also work for other NetRaid controllers but the type
detection for other NetRaids (such as the 1si) will not work due to the
lack of hardware.
Reviewed by: msmith
library: wrong library directory, wrong library extension and wrong
comment). This is mainly of historical interest, if any. The library
that gets removed is aout.
Also, backout the beforeinstall -> afterinstall change in rev.1.20
that was required to install proper telnet.h into /usr/include/arpa.
The actual problem is in <bsd.lib.mk>, and I am going to fix it.
