===
From Nathan Whitehorn:
Open Firmware runs in virtual mode on the Powermac G5. This runs inside the
kernel page table, which preserves all address translations made by OF before
the kernel starts; as a result, the kernel address space is a strict superset of
OF's.
Where this explodes is if OF uses an unmapped SLB entry. The SLB fault handler
runs in real mode and refers to the PCPU pointer in SPRG0, which blows up the
kernel. Having a value of SPRG0 that works for the kernel is less fatal than
preserving OF's value in this case.
===
The result of this is seemingly random panics from NULL dereferences, or hangs
immediately upon boot. By not restoring SPRG0 for Open Firmware entry the
kernel PCPU pointer is preserved and SLB faults are successful, resulting in a
stable kernel.
PR: 205458
Reported by: several (over bugzilla, lists, IRC)
Reviewed by: andreast
Tested by: many (various forms)
MFC after: 2 weeks
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
Add the necessary bits to enable kernel breakpoints for Book-E. The entrypoint
for program exception is very trivial, so rather than expand it to be similar to
AIM, add it into the standard trap handler.
This wasn't blocked out as Book-E specific because it is only a minor redundancy
over AIM, which should have already called db_trap_glue() at this point. If
it's going to panic with a fatal trap anywya, it doesn't matter if it goes
through this path again.
When committing DTrace in 2012/2013 era I inadvertently broke breakpoints, by
setting EXC_DTRACE to the same value as BKPT_INST. Change EXC_DTRACE to a
different, yet logically identical, trap (tw <all>,31,31).
MFC after: 2 weeks
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
Implement get_pcpu() for amd64/sparc64/mips/powerpc, and use it to
replace pcpu_find(curcpu) in MI code.
Reviewed by: andreast, kan, lidl
Tested by: lidl(mips, sparc64), andreast(powerpc)
Differential Revision: https://reviews.freebsd.org/D9587
The types are for the byte offset and page index in vm object. They
are similar to off_t, which is defined as 64bit MI integer. Using MI
definitions will allow to provide consistent MD values of vm
object-related maximum sizes.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
The switch to get_pcpu() in MI code seems to cause hangs on MIPS.
Back out until we can get a better idea of what's happening there.
Reported by: kan, lidl
Freescale added the E.D profile to e500mc and derivative cores. From
Freescale's EREF reference manual this is enabled by a bit in HID0 and should
otherwise default to traditional debug. However, none of the Freescale cores
support that bit, and instead always use E.D. This results in kernel panics
using the standard debug on e500mc+ cores.
Enhanced debug allows debugging of interrupts, including critical interrupts,
as it uses a different save/restore registers (srr*). At this time we don't use
this ability, so instead share the core of the debug handler code between both
handlers.
MFC after: 3 weeks
The desired behavior of atomic_fcmpset_() is to always exit on error. Instead
of retrying on lost reservation, leave the retry to the caller, and return
error.
Reported by: kib
There are no alternatives defined, so there's no point in keeping them. Also,
they weren't around every inline asm block anyway. Without __GNUCLIKE_ASM
defined, the guarded functions return garbage.
Reported by: Andrew Thompson
Summary:
Clang throws the following warning in powerpc intr_machdep:
/usr/src/sys/powerpc/powerpc/intr_machdep.c:454:15: warning: comparison of
constant -1 with expression of type 'enum intr_trigger' is always false
[-Wtautological-constant-out-of-range-compare]
if (i->trig == -1)
~~~~~~~ ^ ~~
This may lead to legitimate problems with aggressive optimizations, if not now
then in the future. To avoid this, add a new enum, INTR_TRIG_INVALID, set to
-1, and use this new enumeration in these checks.
Test Plan: Compile test.
Reviewed By: jhb, kib
Differential Revision: https://reviews.freebsd.org/D9300
Summary:
atomic_fcmpset_*() is analogous to atomic_cmpset(), but saves off the read value
from the target memory location into the 'old' pointer in the case of failure.
Requested by: mjg
Differential Revision: https://reviews.freebsd.org/D9325
Building kernel with devel/powerpc64-gcc (6.2.0) yields the following error:
/usr/src/sys/powerpc/powerpc/db_trace.c:299:20: error: calling
'__builtin_frame_address' with a nonzero argument is unsafe
[-Werror=frame-address]
Work around this by dereferencing the frame address manually instead.
PR: 215600
Reported by: Mark Millard <markmi AT dsl-only DOT net>
MFC after: 2 weeks
Clang apparently requires the explicit form of this instruction, and rejects
uses which ignore the optional cmpD register. This was the only use of the
shorthand form of the instruction, so just fix it up to match the others.
PR: kern/215681
Submitted by: Mark Millard
Reported by: Mark Millard <markmi _AT_ dsl-only.net>
MFC after: 2 weeks
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
There are places where checks are made against VM_MAX_KERNEL_ADDRESS, or
virtual_end (set to VM_MAX_KERNEL_ADDRESS). With 32-bit checks, an address will
always be less than or equal to 0xffffffff. Drop a page, so those checks can
terminate loops safely.
The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".
This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.
PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
Reviewed by: imp, sephe, slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9037
Differential Revision: https://reviews.freebsd.org/D9038
When importing for r309309, as part of conflict resolution, too much extra was
removed, resulting in bad disassembly for branches. Correct this.
Also re-apply the 0->NULL change from r298052.
X-MFC-With: r309309
Before this, it would cause the one consumer of this API in powerpc usage
(dev/dpaa) to set the PTE WIMG flags to empty instead of --M-, making the
cache-enabled buffer portals non-coherent.
Bring in the most recent copy of NetBSD's db_disasm, to fix bugs and add more
instructions.
* Fix several bugs in the disassembler, most notably the disassembly of the
rlwi* instructions, the original reason for bringing in this change.
* Add more registers to the SPR list
* Add more instructions to the opcode table
Obtained from: NetBSD
MFC after: 2 weeks
MPC750 User Manual Errata (rev 1) adds a note to C.4.2.2 noting that mtsr,
mtsrin, and mtmsr all require a isync after the instruction and before data
address translation uses any of the segment registers. This should make FreeBSD
run correctly on the G3 again.
Reported by: Mark Millard
MFC after: 1 week
r309017 removed two fields from struct vmmeter, which is embedded in struct
pcpu. This caused the struct size to change, triggering the CTASSERT in
sys/pcpu.h. Add the extra 8 bytes back in as padding.
vmpage requires struct pmap to exist and contain a pm_stats field. As of
r308817, either AIM or BOOKE is required to be set in order to get their
respective pmap structs. Rather than expose them both, or try to unify them
unnecessarily, add a third option which contains only a pm_stats field, and
change the two existing pmap structures to place the common fields at the
beginning of the struct. This actually fixes the stats collection by libkvm on
AIM hardware, because before it was accessing a possibly different offset, which
would cause it to read garbage.
Bump __FreeBSD_version to denote this ABI change, so that ports which depend on
libkvm can be rebuilt.
Change the pv_tracked flag to an int, just in case userspace decides to include
this file and defines BOOKE.
Guard this block from unintentional inclusion with ifdef BOOKE.
Reported by: emaste
Drop the tracking down to the pmap layer, with optimizations to only track
necessary pages. This should give a (slight) performance improvement, as well
as a stability improvement, as the tracking is already mostly handled by the
pmap layer.
Summary:
This implements part of the gpio-poweroff and gpio-restart device tree
bindings. Optional properties are not handled currently. It also currently
only supports level-triggered reset.
Reviewed By: gonzo
Differential Revision: https://reviews.freebsd.org/D8521
Linux has a slightly different device tree definition for DPAA than originally
done in the FreeBSD driver. This changes the driver to be mostly compatible
with the Linux device tree definitions. Currently the differences are:
bman-portals: compatible = "fsl,bman-portals" (Linux is "simple-bus")
qman-portals: compatible = "fsl,qman-portals" (Linux is "simple-bus")
fman: compatible = "fsl,fman" (Linux is "simple-bus")
The Linux device tree doesn't specify anything for rgmii in the mdio. This
change still requires the device tree to specify the phy-handle, and doesn't yet
support tbi.
Summary:
i.MX5 and PowerPC use a very similar eSDHC controller, which is also
similar to the uSDHC controller used by i.MX6. The imx_sdhci driver works
almost completely with PowerPC, with some minor tweaks.
There is one caveat with this: reset currently does not work on PowerPC, so has
been #ifdef'd out until this can be tracked down and fixed. If resets are done
the controller will timeout all data transactions. Without a reset, it appears
to work just fine.
This is part 3, following up r308186 and r308187.
Test Plan:
This has been tested on a PowerPC QorIQ P1022 board. It has not been
tested on i.MX, but no regressions are expected.
Reviewed By: imp
Differential Revision: https://reviews.freebsd.org/D8407
