was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
all host controllers at the same time, we avoid problems where the BIOS will
actually write to the USB registers of all the USB host controllers every time
we handover one of them, and consequently reset the OS programmed values.
Submitted by: avg
Reviewed by: jhb
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Reported by: erwin
Hardware provided by: TDC A/S
Reviewed by: stas
Tested by: stas
Sun Type 6 USB keyboard support added in rev 1.46 conflicted with
some scan codes used in Japanese keyboards because the scan code
conversion routine was ambiguous for the overlapped codes.
PR: ports/134005
Submitted by: YAMASHIRO Jun
This is needed by the upcoming AR9285 support.
Information on the layout gathered from Linux ath9k.
Not yet connected to the build.
Tested by: Eugeny Dzhurinsky
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.
MFC after: 1 week
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
Also, the previous commit to sys/dev/if_ndis/if_ndis.c also included the
removal of a call to ndis_setstate_80211 that is no longer needed.
Submitted by: sam
MFC after: 3 days
sysctl lock. The 'video' lock now protects the 'bus' of video output
devices attached to a graphics adapter. It is used when iterating over
the list of outputs, etc. The 'video_output' lock is used to lock the
output-specific data similar to a driver lock for the individual video
outputs.
MFC after: 2 weeks
1) Restore the PCI Express control register after a watchdog
reset. This is required because the device will come out
of watchdog reset with the pectl reg at its default state,
and important BIOS configuration (like max payload size)
could be lost.
2) Call mxge_start_locked() for every tx queue before dropping
the lock in the watchdog handler. This is required, as
the queue's buf ring may have filled during the reset.
perform 802.11 operations directly on the ndis0 interface before the
first VAP (wlan0) had been created. This would lead to a NULL-pointer
dereference in the kernel.
Submitted by: Paul B. Mahol <onemda@gmail.com>
MFC after: 3 days
capability to mii(4). Even though AR8132 uses the same model/
revision number of F1 gigabit PHY, the PHY has no ability to
establish 1000baseT link. I have no idea why Atheros use the same
device/model id for this PHY.
With this change atphy(4) does not report 1000baseT media
capability and manual 1000baseT configuration is also disabled
which is more desirable behavior for 10/100Mbps PHY.
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
