correctly tell CAM to requeue the command and then freeze it's queue. The
problem was that when resources became available again, it wouldn't tell
CAM to unfreeze it's queue, so no more commands would ever be delivered.
This is simialr to the bug that was fixed in the cciss driver last year.
This is a bug in 4-STABLE also, but is probably masked by the OS being
fast enough to drain the completion queue before it fills up.
Also add some diagnostics avaialble when compiled with MLY_DEBUG.
Thanks very much to LSI Corp for donating equipment to track this down,
and Vaidus Damosevicius for pestering me long enough to get it fixed.
We may actually be increasing Giant contention doing so because the
actual stuff we do is very cheap.
Also I am not convinced there is not a tiny window for a race here.
Sync with userland test framework which now deals better with pcm feeder kobj
emulation.
Reduce max rate from 96kHz to 48kHz as userland tests found a few bad
points about 90kHz and we don't care about operating up there for now.
DDB when the interrupt button (aka the "programmer's switch") is pressed.
This isn't unfortunately an NMI, but it's a handy way to get into DDB
quickly if needed.
- Move the command timeout check from a separate repeating timeout to the
kthread since the kthread is already running periodically.
- Move printing the hardware print buffer to the kthread.
- Properly shut down the kernel thread on detach.
- Detach the child array devices on detach.
- Don't issue a controller halt command on detach. Doing so requires a PCI
reset to wake the controller back up. The driver can now be unloaded as
long as CAM support is not enabled.
similar patch has been in 4.x for a while, but is more hacky there.)
For this to work, vinum has to be loaded early (e. g. from
boot/loader), for obvious reasons. If the kernel env variable
(aka. loader variable) "vinum.autostart" is set, vinum then asks the
sysctl kern.disks for all available disks in the system, and scans
them for possible vinum headers.
For statically compiled kernels, this behaviour can be obtained even
without boot/loader by using "options VINUM_AUTOSTART" (though this is
not the recommended way).
Alternatively, the 4.x way to specify "vinum.drives" is also supported.
No further hacks (like the 4.x "vinum.root" variable) are needed,
since in 5.x, mountroot() asks back at the drivers to have them
resolve the name of the root FS into a dev_t (using the dev_clone
eventhandler).
(The MFC reminder below is for a partial MFC for vinum.autostart, the
rest is already there in 4.x.)
Timed out on: grog
MFC after: 2 weeks
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie
1) It is already called in init_main.c:proc0_post()
2) It is called each time read_random_phony() called, because "initialized"
variable is never set to 1.
Approved by: markm
- Add hid.h
Obtained from: NetBSD
NOTE: This undoes some changes I'd made to prefix the processor name defines
with PVR_. This was due to my original decision to use MPC750 as a cpu name.
With this changed, the PVR_ change is no longer required.
Remove all the stuff that does not relate to the TSC.
Change the calibration to use DELAY(1000000) rather than trying to check
it against the CMOS RTC, this drastically increases precision:
Using 25 samples on a Athlon 700MHz UP machine I find:
stddev min max average
CMOS 22200 Hz -74980 Hz 34301 Hz 704928721 Hz
DELAY 1805 Hz -1984 Hz 2678 Hz 704937583 Hz
(The difference between the two averages is not statistically significant.)
expressed in PPM of the frequency:
stddev min max
CMOS 31.49 PPM -106.37 PPM 48.66 PPM
DELAY 2.56 PPM 2.81 PPM 3.80 PPM
This code will not be used until a followup commit to sys/isa/clock.c
and sys/pc98/pc98/clock.c which will only happen after some field testing.
