the pwm values. We can now set the fan's speed of a PWM controlled fan
with % numbers between 30 and 100 % instead of trying to model a
% number based on rpm.
The fcu chip offers both, the dutycycle and the rpm value of the PWM
controlled fans. I added the rpm value to the list of information
available via sysctl(8).
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
and just show old (cached) values. Controller will not respond to
the command unless MAC is enabled so DUMP request for down
interface caused request timeout.
RealTek changed TX descriptor format for later controllers so these
controllers require MSS configuration in different location of TX
descriptor. TSO is enabled by default for controllers that use new
descriptor format.
For old controllers, TSO is still disabled by default due to broken
frames under certain conditions but users can enable it.
Special thanks to Hayes Wang at RealTek.
MFC after: 2 weeks
These controllers consist of two Marvell 88SE9128 6Gbps SATA chips and
PLX PCIe bridge. As result, they seem to be agree to work with ahci(4)
as usual HBAs. The only noticed issue is that RAID BIOS disables all
drive caches during boot, though `camcontrol cmd ...` is able to fix that.
Those who wants RAID functionality can still use closed proprietary driver
from HighPoint site.
MFC after: 1 week
erroneously, assumed that 4 bytes of data were in the first
mbuf of a list by replacing the bcopy() with m_copydata().
Also, replace the uses of m_pullup(), which can fail for
reasons other than not enough data, with m_copydata().
For the cases where it isn't known that there is enough
data in the mbuf list, check first via m_len and m_length().
This is believed to fix a problem reported by dpd at dpdtech.com
and george+freebsd at m5p.com.
Reviewed by: jhb
MFC after: 8 days
accurate. <sys/linker_set.h> is one of the very few headers similar to
<sys/queue.h> for which nested includes is allowed.
PR: docs/153654
Reviewed by: bde
MFC after: 1 month
install or remove non-SCI interrupt handlers per ACPI Component Architecture
User Guide and Programmer Reference. ACPICA may install such interrupt
handler when a GPE block device is found, for example. Add a wrapper for
ACPI_OSD_HANDLER, convert its return values to ours, and make it a filter.
Prefer KASSERT(9) over panic(9) as we have never seen those in reality.
Clean up some style(9) nits and add my copyright.
DMA boundary bug and runs with PCI-X mode. watchdog timeout was
observed on BCM5704 which lives behind certain PCI-X bridge(e.g.
AMD 8131 PCI-X bridge). It's still not clear whether the root
cause came from that PCI-X bridge or not. The watchdog timeout
indicates the issue is in TX path. If the bridge reorders TX
mailbox write accesses it would generate all kinds of problems but
I'm not sure. This should be revisited.
Tested by: Michael L. Squires (mikes <> siralan dot org)
issue seen on PCIX BCM5704 controller. r216970 fixed the issue but
the DMA address space restriction was applied to all bge(4)
controllers such that it caused unnecessary performance degradation
for controllers that have no such issues.
o) Clear/acknowledge receive interrupt at end of thread. This gives the
management interfaces performance on the order of 100Mbps rather than
the previous level of 10Mbps on my MR-730.
hint is 0 when no SACK data is received to update the hint with. This was
accidentally omitted from r216753.
Sponsored by: FreeBSD Foundation
MFC after: 10 weeks
X-MFC with: 216753
o) Add 'octm', a trivial driver for the 10/100 management ports found on some
Octeon systems.
o) Make the Simple Executive's management port helper routines compile on
FreeBSD (namely by not doing math on void pointers.)
o) Add a cvmx_mgmt_port_sendm routine to the Simple Executive to send an mbuf
so there is only one copy in the transmit path, rather than having to first
copy the mbuf to an intermediate buffer and then copy that to the Simple
Executive's transmit ring.
o) Properly work out MII addresses of management ports on the Lanner MR-730.
XXX The MR-730 also needs some patches to the MII read/write routines, but
this is sufficient for now. Media detection will be fixed in the future
when I can spend more time reading the vendor-supplied patches.
quite awful, because e.g. 4 packets will come in and get processed on 4
different cores at the same time, really battling with the TCP stack quite
painfully. For now, just run one task at a time.
This gets performance up in most cases to where it was before the correctness
fixes that got interrupts to run on all cores (except in high-load TCP transmit
cases where all we're handling receive for is ACKs) and in some cases it's
better now. What would be ideal would be to use a more advanced interrupt
mitigation strategy and possibly to use different workqueue groups per port for
multi-port systems, and so on, but this is a fine stopgap.
all new devices added between our r211022 and their git revision
93ad03d60b5b18897030038234aa2ebae8234748
Also correct a Foxconn entry.
MFC after: 1 week
manner analogous to r216633 for the regular server. This
change busies the file system so that VFS_VGET() is
guaranteed to be using the correct mount point even
during a forced dismount attempt. Since nfsd_fhtovp() is
not called immediately before readdirplus, the patch is
actually a clone of pjd@'s nfs_serv.c.4.patch instead of
the one committed in r216633.
Reviewed by: kib
MFC after: 10 days
these variables represent sizes in one capacity or another. There is
no reason to allow negative numbers. Change userspace shared structure
elements that get used for the modified functions from int to uint32_t,
since it's not clear what userspace programs use these fields, and we
do not want to break binary compatibility. This fixes a panic when
corrupt or bogus data is passed into the kernel.
Obtained from: NetBSD
MFC after: 3 weeks
need it anymore. Moreover, its implementation had a type mismatch, a
long is not necessarily an uint64_t. (This mismatch was hidden by
casting.) Move the remaining two counters up a level in the sysctl
hierarchy. There is no reason for them to be under the vm.pmap node.
Reviewed by: kib
an unbound socket, regardless of any multicast options.
If an address is specified via a multicast option, then
let it override normal the source address selection.
This fixes a bug where source address selection was
not being performed when multicast options were present
but without an interface being specified.
Reviewed by: bz
MFC after: 1 day
That revision is introducing a bug which is more visible than problems
it is trying to fix.
As long as my time is very limited in this period I am going to
commit back this patch just once it is fully fixed.
Reported by: dim, Nicholas Esborn
