to 0x600 via a 'rep movsw'. Once that was done, %cx was zero, so we could
simply use 'movb' to update the lower byte of %cx in preparation for
zeroing out the fake partition entry used to boot to other drives via F5.
Well, in the new boot0, we don't actually relocate ourselves, instead it
is easier to create the fake partition entry first and then just use it to
get the BIOS to load all of boot0 into memory at 0x600. However, since we
aren't doing the relocate code anymore, we don't know that %cx == 0 when
we hit the 'movb' to setup %cx for clearning the fake partition entry.
Thus, if %ch != 0 when the BIOS started boot0, then it would end up zeroing
a lot more memory than just 8 words. The solution is to do a word move of
$8 into %cx.
Debugging help from: David Wolfskill <dhw@whistle.com>
explanations into a new file "refuse.README". Some users are simply
copying these files and expecting them to work -- without even
reading them. I don't want to spend any more time closing bogus
PRs from that.
Also correct an error or two in the patterns.
display control by apm -d.
- Remove APM_DEBUG to avoid re-build kernel with such a unspported optioin.
- Introduce new denug flag `debug.apm_debug' which can be controlled by
sysctl interface and loader by setting like "debug.apm_debug=1", you
will get debug messages from APM driver.
- Add some enhancements from linux on display control by apm -d. I'm
expecting that we can see some improvements on some laptops where
apm -d doesn't work correctly so far.
Reviewed by: -mobile and -current folks (no objection)
Suggested by: Susumu WAKABAYASHI <susumu@wakabaya.net>
modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
the scratch RAM for data normally found in the SEEPROM (presumably in the
event that the SEEPROM is unavailable or can't be read). This code causes
a spontaneous reboot on monster.osd.bsdi.com, which has an embedded aic7880
controller. The problem appears to happen either when it writes to the
SCBPTR port and then reads from the SCB_CONTROL port. Somewhere during
the inb/outb operations, the system has a heart attack and restarts.
This code looks very suspicious, particularly since it has unconditionalized
debug mesages such as "Got here!" and "And it even worked!". With this
block #ifdef'ed out, the machine boots and runs properly. I stronly suggest
that it stay #ifdef'ed out until it's properly tested.
<stand.h>. Also, since bcache_strategy() used to not have a prototype,
arcdisk happily called bcache_strategy() with 6 parameters instead of 7,
leaving out the disk unit number, which is the 2nd parameter. Add in the
unit number to the bcache_strategy() call to fix this.
When this happens, we know for sure that the packet data was not
received by the peer. Therefore, back out any advancing of the
transmit sequence number so that we send the same data the next
time we transmit a packet, avoiding a guaranteed missed packet and
its resulting TCP transmit slowdown.
In most systems ip_output() probably never returns an error, and
so this problem is never seen. However, it is more likely to occur
with device drivers having short output queues (causing ENOBUFS to
be returned when they are full), not to mention low memory situations.
Moreover, because of this problem writers of slow devices were
required to make an unfortunate choice between (a) having a relatively
short output queue (with low latency but low TCP bandwidth because
of this problem) or (b) a long output queue (with high latency and
high TCP bandwidth). In my particular application (ISDN) it took
an output queue equal to ~5 seconds of transmission to avoid ENOBUFS.
A more reasonable output queue of 0.5 seconds resulted in only about
50% TCP throughput. With this patch full throughput was restored in
the latter case.
Reviewed by: freebsd-net
page.
Add ability to run "inetd -R 0" to disable the default connection
per minute limit of 256 connections. Document this in man page.
Don't use maxchild as a boolean - instead check if it is greater
than zero.
Reviewed by: sheldonh
Based on a patch by: Alexander Langer <alex@big.endian.de>
Remove extra parens from my host selection commit.
Add white space after if, while, for and switch.
Get rid of braces around a single statement if.
There should be no functional changes in this commit.
Reviewed by: sheldonh
