opens if the reference count is not decremented on close.
Note that this may result in the reference count being corrupted
on full duplex devices (due to mismatching opens/closes), but the
code doesn't use the reference count for anything on full duplex
devices.
2. Offer half duplex with both playback and record on channel 1 or
full duplex with playback always on channel 2 as a compile-time option.
3. 16 bit record output is byte swapped for some dumb reason. Report the _BE
AFMTs for recording.
usb, all in usb.ko. uhub depends on usb. The bug was that the preload
processing only adds a module to the list once it's internal dependencies
are resolved... Since it was not "seeing" the internal usb module it
believed that uhub had a missing dependency.
if you kldload this driver, all the subordinate devices are probed/attached
as expected. But this is not the case when the driver is statically compiled
into the kernel. Since I do most of my testing with modules, I failed to
notice this. I'm not sure if it's intended behavior or not. I think it may
be, but it seems a little counter-intuitive.
sector 0 of a disk and boot0.5 is the `boot selector' which starts
from address 0x400. The IPL loads boot0.5 and boot0.5 loads bootblock
of a slice.
The boot manager stuff was developed by me (kato) with Borland C++,
and then, translated into bcc in the ports collection by Nokubi-san.
After that, boot0 has been translated into gas with the .code16
directive by Takahashi-san (nyan) and boot0.5 has been rewritten in
gas by me.
16 bit samples have some sort of choppiness, the nature of which
is not completely clear, but it clearly has something to do with
dma buffer synchronization. But at least channel 1 makes noise now.
Previously, using -S/--skip, -f/--force, or -t/--batch to skip a patch in
a patchset still registers a failure which causes patch to return a
non-zero exit code. This is particularly undesirable with regards to
ports as there is no way to ignore the non-zero code. (Luckily, we don't
currently have any ports that make use of any of these options.)
The PR (yes, my own) is slightly incorrect: It states that -f does indeed
properly skip patches. It does, but it still sets the failure flag causing
patch to return non-zero.
PR: 19638
Submitted by: kbyanc@posi.net
appears to be the correct length, but quality of output has not yet
been tested. Also, full duplex audio (that is, playback on channel 1)
does not yet work. Two constants and I am there!
Obtained from: major hints from ALSA
with LEDs on some cards being stomped on when clearing the "jabber disable"
bit. Using DC_SETBIT() has an unwanted side effect of setting a write enable
bit in the watchdog timer register which we really want to be cleared when
we do a write.
has set pwok to a non-zero value.
Previously, the fact that skey.access(5) allowed UNIX passwords for
this connection attempt was ignored, even in the NOPAM case.
This only addresses the NOPAM case; when libpam is used, the problem
will persist.
PR: 20333
since it could potentially depend on any ${DESTDIR}/usr/include
preprocessor file. This fixes the broken -DNOCLEAN world build
I experienced yesterday.
It seems as if uninitialised memory was the culprit.
We may want to contribute this back to the OpenSSH project.
Submitted by: Alexander Leidinger <Alexander@Leidinger.net> on -current.
changes is that there's now a Solaris port of this driver, so some things
in the core version had to change (not much, but some).
In order, from the top.....:
A lot of error strings are gathered in one place at the head of the file.
This caused me to rewrite them to look consistent (with respect to
things like 'Port 0x%' and 'Target %d' and 'Loop ID 0x%x'.
The major mailbox function, isp_mboxcmd, now takes a third argument,
which is a mask that selectively says whether mailbox command failures
will be logged. This will substantially reduce a lot of spurious noise
from the driver.
At the first run through isp_reset we used to try and get the current
running firmware's revision by issuing a mailbox command. This would
invariably fail on alpha's with anything but a Qlogic 1040 since SRM
doesn't *start* the f/w on these cards. Instead, we now see whether we're
sitting ROM state before trying to get a running BIOS loaded f/w version.
All CFGPRINTF/PRINTF/IDPRINTF macros have been replaced with calls to
isp_prt. There are seperate print levels that can be independently
set (see ispvar.h), which include debugging, etc.
All SYS_DELAY macros are now USEC_DELAY macros. RQUEST_QUEUE_LEN and
RESULT_QUEUE_LEN now take ispsoftc as a parameter- the Fibre Channel
cards and the Ultra2/Ultra3 cards can have 16 bit request queue entry
indices, so we can make a 1024 entry index for them instead of the
256 entries we've had until now.
A major change it to fix isp_fclink_test to actually only wait the
delay of time specified in the microsecond argument being passed.
The problem has always been that a call to isp_mboxcmd to get he
current firmware state takes an unknown (sometimes long) amount of
time- this is if the firmware is busy doing PLOGIs while we ask
it what's up. So, up until now, the usdelay argument has been
a joke. The net effect has been that if you boot without being plugged
into a good loop or into a switch, you hang. Massively annonying, and
hard to fix because the actual time delta was impossible to know
from just guessing. Now, using the new GET_NANOTIME macros, a precise
and measured amount of USEC_DELAY calls are done so that only the
specified usecdelay is allowed to pass. This means that if the initial
startup of the firmware if followed by a call from isp_freebsd.c:isp_attach
to isp_control(isp, ISP_FCLINK_TEST, &tdelay) where tdelay is 2 * 1000000,
no more than two seconds will actually elapse before we leave concluding
that the cable is unhooked. Jeez. About time....
Change the ispscsicmd entry point to isp_start, and the XS_CMD_DONE
macro to a call to the platform supplied isp_done (sane naming).
Limit our size of request queue completions we'll look at at interrupt
time. Since we've increased the size of the Request Queue (and the
size of the Response Queue proportionally), let's not create an
interrupt stack overflow by having to keep a max completion list
(forw links are not an option because this is common code with
some platforms that don't have link space in their XS_T structures).
A limit of 32 is not unreasonable- I doubt there'd be even this many
request queue completions at a time- remember, most boards now use
fast posting for normal command completion instead of filling out
response queue entries.
In the isp_mboxcmd cleanup, also create an array of command
names so that "ABOUT FIRMWARE" can be printed instead of "CMD #8".
Remove the isp_lostcmd function- it's been deprecated for a while.
Remove isp_dumpregs- the ISP_DUMPREGS goes to the specific bus
register dump fucntion.
Various other cleanups.
