vm_pager_object_lookup() already referenced the object.
Note that there is no in-tree consumers of cdev_pager_lookup(). The
only known user of the function is i915 gem driver, which is not yet
imported. This should make the KPI change minor.
Submitted by: avg
MFC after: 1 week
Since ino_t size is about to change to 64-bits, replace ino_t used in
dump protocol definition with 32-bit dump_ino_t to preserve backward
compatibility. At some point, it may be necessary to use spare fields
in struct in order to fully support 64-bit inode numbers.
Sponsored by: Google Summer of Code 2011
longer uses the active and inactive paging queues. Instead, the pmap now
maintains an LRU-ordered list of pv entry pages, and pmap_pv_reclaim() uses
this list to select pv entries for reclamation.
Note: The old pmap_collect() tried to avoid reclaiming mappings for pages
that have either a hold_count or a busy field that is non-zero. However,
this isn't necessary for correctness, and the locking in pmap_collect() was
insufficient to guarantee that such mappings weren't reclaimed. The new
pmap_pv_reclaim() doesn't even try.
Reviewed by: kib
MFC after: 6 weeks
to freebsd-fs@, where the setfacl of an NFSv4 acl would fail.
This was caused by the VOP_ACLCHECK() call for ZFS replying
EOPNOTSUPP. After discussion with rwatson@, it was determined
that a call to VOP_ACLCHECK() before doing VOP_SETACL() is not
required. This patch fixes the problem by deleting the
VOP_ACLCHECK() call.
Tested by: Andrew Leonard (previous version)
MFC after: 1 week
That is, build crtbeginS.o and crtendS.o instead of crtbegin.So and
crtend.So. Remove the name substitution during install.
Obtained from: Juniper Networks, Inc.
Supermicro LCD screen modules seem to not support accessing reports through
the control pipes, but working fine with the interrupt pipes.
Sponsored by: iXsystems, Inc.
MFC after: 1 week
The NAND Flash environment consists of several distinct components:
- NAND framework (drivers harness for NAND controllers and NAND chips)
- NAND simulator (NANDsim)
- NAND file system (NAND FS)
- Companion tools and utilities
- Documentation (manual pages)
This work is still experimental. Please use with caution.
Obtained from: Semihalf
Supported by: FreeBSD Foundation, Juniper Networks
The code previously assumed that copyin/copyout did no
address translation and that the device tree blob could
be manipulated in-place (with only a few adjustments for
the ELF loader offset). This isn't possible on all platforms,
so the revised code uses copyout() to copy the device tree
blob into a heap-allocated buffer and then updates the
device tree with copyout(). This isn't ideal, since it
bloats the loader memory usage, but seems the only feasible
approach (short of rewriting all of the fdt manipulation
routines).
8.x code:
- If the lock cannot be acquired immediately unlocks 'bar' vnode
and then locks both vnodes in order.
- wrong vnode type panics from cache_enter_time after calls by
ext2_lookup.
The fix merges the fixes from ufs/ufs_lookup.c.
Submitted by: Mateusz Guzik
Approved by: jhb@ (mentor)
Reviewed by: kib@
MFC after: 1 week
Entries with zero inode number are considered placeholders by libc and
UFS. Fix remaining uses of VOP_READDIR in kernel: vop_stdvptocnp,
unionfs.
Sponsored by: Google Summer of Code 2011
add some more BAR debugging logic.
* Change the definition of ath_debug and ath_softc.sc_debug from
int to uint64_t;
* Change the relevant sysctls;
* Add a new BAR TX debugging field;
* Use this in if_ath_tx.
This has been tested by using the sysctl program, which happily allows
for fields > 32 bits to be configured.
used as a replacement for libgcc on sparc64 would cause a 60% decrease in
performance is wrong. Actually, the performance loss is only marginal and
the huge difference seen was caused by a pilot error comparing libgcc builds
using MALLOC_PRODUCTION with libcompiler_rt builds that did not.
Although I _should_ handle the other errors in various ways (specifically
errors like FILT), treating them as having transmitted successfully
is completely wrong. Here, they'd be counted as successful and the BAW
would be advanced.. but the RX side wouldn't have received them.
The specific errors I've been seeing here are HAL_TXERR_FILT.
This patch does fix the issue - I've tested it using -i 0.001 pings
(enough to start aggregation) and now the behaviour is correct:
* The RX side never sees a "moved window" error, and
* The TX side sends BARs as needed, with the RX side correctly handling
them.
PR: kern/167902
compatible with the sched provider implemented by Solaris and its open-
source derivatives. Full documentation of the sched provider can be found
on Oracle's DTrace wiki pages.
Note that for compatibility with scripts originally written for Solaris,
serveral probes are defined that will never fire. These probes are defined
to fire when Solaris-specific features perform certain actions. As these
features are not present in FreeBSD, the probes can never fire.
Also, I have added a two probes that are not defined in Solaris, lend-pri
and load-change. These probes have been added to make it possible to
collect schedgraph data with DTrace.
Finally, a few probes are defined in Solaris to take a cpuinfo_t *
argument. As it was not immediately clear to me how to translate that to
FreeBSD, currently those probes are passed NULL in place of a cpuinfo_t *.
Sponsored by: Sandvine Incorporated
MFC after: 2 weeks
