the mbuf chain. If we ever get a buggy caller, a bogus "off" should
be caught by the sanity check at the function entry. Null "m" here
means a very unusual condition of a totally broken mbuf chain (wrong
m_pkthdr.len or whatever), so we can just page fault later.
Found by: Coverity Prevent(tm)
CID: 825
tree... John Baldwin noted that sio might pass values between probe
and attach via softc. It appears that sio does leave the hardware in
a known state after probing, so other drivers that try to probe might
leave it in a worse state. It doesn't seem to pass any data in softc,
however, that I could find... I think we should not be probing for
anything but nonPnP isa, but that's a change for another day.
Submitted by: Frank Behrens
PR: 87845
except in places dealing with ifaddr creation or destruction; and
in such special places incomplete ifaddrs should never be linked
to system-wide data structures. Therefore we can eliminate all the
superfluous checks for "ifa->ifa_addr != NULL" and get ready
to the system crashing honestly instead of masking possible bugs.
Suggested by: glebius, jhb, ru
a local 'semid' variable which was the array index and used uap->semid
as the original IPC id. During the kern_semctl() conversion those two
variables were collapsed into a single 'semid' variable breaking the
places that needed the original IPC ID. To fix, add a new 'semidx'
variable to hold the array index and leave 'semid' unmolested as the IPC
id. While I'm here, explicitly document that the (undocumented, at least
in semctl(2)) SEM_STAT command curiously expects an array index in the
'semid' parameter rather than an IPC id.
Submitted by: maxim
used since FreeBSD-SA-06:04.ipfw.
Adopt send_reject6 to what had been done for legacy IP: no longer
send or permit sending rejects for any but the first fragment.
Discussed with: oleg, csjp (some weeks ago)
Previously, another thread could get a pointer to the
interface by scanning the system-wide list and sleep
on the global vlan mutex held by vlan_unconfig().
The interface was gone by the time the other thread
woke up.
In order to be able to call vlan_unconfig() on a detached
interface, remove the purely cosmetic bzero'ing of IF_LLADDR
from the function because a detached interface has no addresses.
Noticed by: a stress-testing script by maxim
Reviewed by: glebius
tested and then set. [1]
Reorganise things to eliminate this, we now ensure that enc0 can not be
destroyed which as the benefit of no longer needing to lock in
ipsec_filter and ipsec_bpf. The cloner will create one interface during the
init so we can guarantee that encif will be valid before any SPD entries are
added to ipsec.
Spotted by: glebius [1]
cards: the chips are all marked "RTL8111B", but they put stickers on the
back that say "RTL8168B/8111B". The manual says there's only one HWREV code
for both the 8111B and 8168B devices, which is 0x30000000, but the cards
they sent me actually report HWREV of 0x38000000. Deciding to trust the
hardware in front of me rather than a possibly incorrect manual (it wouldn't
be the first time the HWREVs were incorrectly documented), I changed the
8168 revision code. It turns out this was a mistake though: 0x30000000
really is a valid for the 8168.
There are two possible reasons for there to be two different HWREVs:
1) 0x30000000 is used only for the 8168B and 0x38000000 is only for
the 8111B.
2) There were 8111/8168 rev A devices which both used code 0x30000000,
and the 8111B/8168B both use 0x38000000.
The product list on the RealTek website doesn't mention the existence of
any 8168/8111 rev A chips being in production though, and I've never seen
one, so until I get clarification from RealTek, I'm going to assume that
0x30000000 is just for the 8168B and 0x38000000 is for the 8111B only.
So, the HWREV code for the 8168 has been put back to 0x30000000,
a new 8111 HWREV code has been added, and there are now separate
entries for recognizing both devices in the device list. This will
allow all devices to work, though if it turns out I'm wrong I may
need to change the ID strings
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
OpenBSD. This driver seems to give a small performance increase, and
should lead to better maintainability in the future.
The nForce Ethernet-specific hack in sys/i386/xbox/xbox.c is still
required, judging from dev/nfe/if_nfe.c. The condition it hacks will
almost certainly only occur on XBOX-es anyway, so it is best left there.
Approved by: imp (mentor)
one byte less than needed.
This is a RELENG_x_y candidate, since it fixes a problem with Oracle 10.
Noticed by: Dmitry Ganenko <dima@apk-inform.com>
Testcase by: Dmitry Ganenko <dima@apk-inform.com>
Reviewed by: des
Submitted by: rdivacky
Sponsored by: Google SoC 2006
MFC after: 1 week
- process state (idle, sleeping, running, ...) [1]
- the process group ID of the process which owns the connected tty
- some page fault stats
- time spend in kernel/userland
- priority/nice value
- starttime [1]
- memory/swap stats
- scheduling policy
Additionally add some new fields and correct some not filled out ones.
This brings us down to 15 dummy fields.
The fields marked with [1] are needed to get Oracle 10 running. The starttime
field is not completely right, since it displays the _same_ starttime for
_every_ process, but at least it is not 0 and Oracle accepts this.
This is a RELENG_x_y candidate.
Noticed by: Dmitry Ganenko <dima@apk-inform.com> [1]
Reviewed by: des, rdivacky
MFC after: 1 week
