If an error occurs when transmitting one mbuf in a chain of fragments,
free the subsequent fragments instead of leaking them.
Sponsored by: ADARA Networks
the FIFO.
I still see some corner cases where no RX occurs when it should be
occuring. It's quite possible that there's a subtle race condition
somewhere; or maybe I'm not programming the RX queues right.
There's also no locking here yet, so any reset/configuration path
state change (ie, enabling/disabling receive from the ioctl, net80211
taskqueue, etc) could quite possibly confuse things.
* For now, kickpcu should hopefully just do nothing - the PCU doesn't need
'kicking' for Osprey and later NICs. The PCU will just restart once
the next FIFO entry is pushed in.
* Teach "proc" about "dosched", so it can be used to just flush the
FIFO contents without adding new FIFO entries.
* .. and now, implement the RX "flush" routine.
* Re-initialise the FIFO contents if the FIFO is empty (the DP is NULL.)
When PCU RX is disabled (ie, writing RX_D to the RX configuration
register) then the FIFO will be completely emptied. If the software FIFO
is full, then no further descriptors are pushed into the FIFO and
things stall.
This all requires much, much more thorough stress testing.
debugger exited without calling ptrace(PT_DETACH), there is a time window
that the p_xthread may be pointing to non-existing thread, in practical,
this is not a problem because child process soon will be killed by parent
process.
This is inspired by ath9k and the reference driver, but it's a new
implementation of the RX FIFO handling.
This has some issues - notably the FIFO needs to be reprogrammed when
the chip is reset.
* Add a couple of RX errors;
* Add the spectral scan PHY error code;
* extend the RX flags to be a 16 bit field, rather than an 8 bit field;
* Add a new RX flag.
Obtained from: Qualcomm Atheros
on x86 and use that to implement stop_emulating() in the fpu/npx code.
Reimplement start_emulating() in the non-XEN case by using load_cr0() and
rcr0() instead of the 'lmsw' and 'smsw' instructions. Intel explicitly
discourages the use of 'lmsw' and 'smsw' on 80386 and later processors in
the description of these instructions in Volume 2 of the ADM.
Reviewed by: kib
MFC after: 1 month
switch to its vnet before calling ether_ifdetach(). Otherwise if the
second half resides in a different vnet, if_detach() silently fails
leaving a stale pointer in V_ifnet list, and the system crashes trying
to access this pointer later.
Another solution could be not to allow to destroy epair unless both
ends are in the home vnet.
Discussed with: bz
Tested by: delphij
The last 12 bits of the limit registers have to be set to 1. These
bits are not significant in bridge BARs and are 0 on read, but the
bits are valid in the swap limit register and needs to be set.
to attach to the process, it is surprising that the process is resumed
without inputting any gdb commands, however ptrace manual said:
The tracing process will see the newly-traced process stop and may
then control it as if it had been traced all along.
But the current code does not work in this way, unless traced process
received a signal later, it will continue to run as a background task.
To fix this problem, just send signal SIGSTOP to the traced process after
we resumed it, this works like that you are attaching to a running process,
it is not perfect but better than nothing.
- Add -P option to support PID file. When -a is specified /var/run/rarpd.pid
is used, and when an interface is specified /var/run/rarpd.<ifname>.pid is
used by default.
The AR93xx and later chips support two RX FIFO queues - a high and low
priority queue.
For legacy chips, just assume the queues are high priority.
This is inspired by the reference driver but is a reimplementation of
the API and code.
