The epoch stuff with taskqueues works fine if the driver never calls
the receive path in other contexts, but this driver does. If there was
a chip reset during active receive then part of the reset will call
the receive path to flush out any active packets before reinitialising
the receive queue and that needs to be done with the epoch held.
So:
* make the receive task a normal task again
* explicitly call epoch enter/exit around the legacy and newer DMA
receive paths
* add a couple of epoch asserts to ensure that the receive packet
path itself is called with epoch held.
This fixes it on my Atom eeepc laptop (circa 2010!) that I did
all of my initial 802.11n work in this driver and net80211.
Tested:
* AR9285, STA mode
TODO:
* Test on EDMA chipset (AR9380)
* Test in AP/adhoc modes, just to be sure (eg for beacon
receive processing in particular.)
Document better this file, updating the URL to the IANA registry and closely
match the official services.
For system ports (0 to 1023) we now try to follow the registry closely, noting
some historical differences where applicable.
For the User ports (1024 - 49151) we try to keep some sensible balance only
of services that are likely to be found on FreeBSD/UNIX systems. This attempts
to strike a balance between complexity and usefulness.
As a side effect: drop references to unofficial Kerberos IV which was EOL'ed
on Oct 2006[1]. While it is conceivable some people may still use it in some
very old FreeBSD machines that can't be replaced easily, the use of it is
considered a security risk. Also drop the unofficial netatalk, which we
supported long ago in the kernel but was dropped long ago.
[1] https://web.mit.edu/kerberos/krb4-end-of-life.html
MFC after: 3 weeks (likely to 12-stable only)
Differential Revision: https://reviews.freebsd.org/D23621
fd.
The read built-in command calls read(2) with a 1-byte buffer because
newline characters need to be detected even on a byte stream which
comes from a non-seekable file descriptor. Because of this, the
following script calls >6,000 read(2) to show a 6KiB file:
while read IN; do echo "$IN"; done < /COPYRIGHT
When the input byte stream is seekable, it is possible to read a data
block and then reposition the file pointer to where a newline
character found. This change adds a small buffer to do this and
reduces the number of read(2) calls.
Theoretically, multiple built-in commands reading the same seekable
byte stream in a single pipe chain can share the buffer. However,
this change just makes a single invocation of the read built-in
allocate a buffer and deallocate it every time for simplicity.
Although this causes read(2) to read the same regions multiple times,
the performance penalty should be small compared to the reduction of
read(2) calls.
Reviewed by: jilles
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23747
Don't convert all lower layer errors to EIO. Instead, pass the actual error up
the stack. This will allow the upper layers that look for ENXIO to react
properly to that signal from the lower layers and, for UFS, unmount the
filesystem.
Reviewed by: kib@
Differential Revision: https://reviews.freebsd.org/D23755
smbios used to be an i386 only kinda weird quirk to the x86
architecture. But UEFI picked it up, dusted it off and now it's many
other locations. Make it base technology by moving it to libsa and
fixing up the compliation. The code has issues with unaligned access
still, but that will be addressed in a followup commit.
Differential Revision: https://reviews.freebsd.org/D23660
Create a ptov() function. It's basically the same as the btx PTOV
macro, but works everywhere. smbios needs this to translate addresses,
but the translation differs between BIOS booting and EFI booting. Make
it a function so one smbios.o can be used everywhere. Provide
definitions for it in the two loaders affected.
Differential Revision: https://reviews.freebsd.org/D23660
There's no need to spam the console with this error message. If there's an I/O
error, the disk/cam driver will report it at the lower levels. If that's an
actual problem, the upper layers will report that.
Reviewed by: kib@
Differential Revision: https://reviews.freebsd.org/D23756
possible enum in a switch statement. I verified that this emits nothing
as expected on clang. radix relies on constant propagation to eliminate
any branching from these access routines.
Reported by: lwhsu/tinderbox
Summary:
With COMPILER_FREEBSD_VERSION, we use a numeric value that we bump each
time we make a change that requires re-bootstrapping, but with the
linker variant, we instead take the entire part after "FreeBSD", as in
this example version output:
LLD 9.0.1 (FreeBSD c1a0a213378a458fbea1a5c77b315c7dce08fd05-1300006) (compatible with GNU linkers)
E.g., LINKER_FREEBSD_VERSION is currently being set to
"c1a0a213378a458fbea1a5c77b315c7dce08fd05-1300006". This means that
*any* new upstream lld version will cause re-bootstrapping.
We should only look at the numerical field we append after a dash
instead. This review attempts to make it so.
The only thing I am not happy about is the post-processing of awk output
in Makefile.inc1. I notice that our awk does not have gensub(), so it
can't substitute a numbered sub-regex with \1, \2, etc. Suggestions
welcome. :)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23691
The tree is kept correct for readers with store barriers and careful
ordering. The existing object lock serializes writers. Consumers
will be introduced in later commits.
Reviewed by: markj, kib
Differential Revision: https://reviews.freebsd.org/D23446
This gives much better concurrency when there are a large number of
cores per-domain and multiple domains. Avoid taking the lock entirely
if it will not be productive. ROUNDROBIN domains will have mixed
memory in each domain and will load balance to all domains.
While here refactor the zone/domain separation and bucket limits to
simplify callers.
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D23673
For some reason build+package+test time went from about 1h10 to over
1h30 (killed due to timeout prior to completion).
The reason for the increase still needs investigation.
This is the kdump counterpart of the truss support added in r358116, and
also a part of D23733. shm_open2 is the successor to shm_open.
Reviewed by: kaktus
shm_open2 is similar to shm_open, except it also takes shmflags and optional
name to label the anonymous region for, e.g., debugging purposes.
The appropriate support for decoding shmflags was added to libsysdecode in
r358115.
This is a part of D23733.
Reviewed by: kaktus
Any SHM_* flag here is (and likely will continue to be) a shmflag that may
be passed to shm_open2(), with exception to SHM_ANON. This is a prereq to
adding appropriate support to truss/kdump.
Reviewed by: kaktus (slightly earlier version)
Differential Revision: https://reviews.freebsd.org/D23733
The first argument to shm_open(2) as well as shm_open2(2) may be a path or
SHM_ANON. Decode SHM_ANON, at least- paths will show up as namei results in
kdump output, which may be sufficient; in those cases, we'll have printed an
address.
Future commits will add support for shm_open2() to libsysdecode/truss/kdump.
Reported by: kaktus
MFC after: 3 days
environ(7) was in AT&T Version 7
ac(8): Add a HISTORY section
sa(8): Add a HISTORY section
sqrt(3): Add the actual sqrt function to the HISTORY section
Obtained from: OpenBSD
Submitted by: gbergling@gmail.com
Approved by: bcr@(mentor)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23693
be able to guarantee that they can be racquired without blocking.
Reviewed by: kib
Discussed with: markj
Differential Revision: https://reviews.freebsd.org/D23506
virtual address or physical page allocation need to be marked with this
flag.
Reviewed by: markj
Tested by: pho
Differential Revision: https://reviews.freebsd.org/D23712
This API is intended to provide some measure of safety with SMR
protected pointers. A struct wrapper provides type checking and
a guarantee that all access is mediated by the API unless abused. All
modifying functions take an assert as an argument to guarantee that
the required synchronization is present.
Reviewed by: kib, markj, mjg
Differential Revision: https://reviews.freebsd.org/D23711
ACPI Control Method Batteries have a _BIF and/or _BIX object which
provide static properties of the battery. FreeBSD acpi_cmbat module
supported _BIF object only, which was deprecated as of ACPI 4.0.
_BIX is an extended version of _BIF defined in ACPI 4.0 or later.
As of writing, _BIX has two revisions. One is in ACPI 4.0 (rev.0) and
another is in ACPI 6.0 (rev.1). It seems that hardware vendors still
stick to _BIF only or _BIX rev.0 + _BIF for the maximum compatibility.
Microsoft requires _BIX rev.0 for Windows machines, so there are some
laptop machines with _BIX rev.0 only. In this case, FreeBSD does not
recognize the battery information.
After this change, the acpi_cmbat module gets battery information from
_BIX or _BIF object and internally uses _BIX rev.1 data structure as
the primary information store in the kernel. ACPIIO_BATT_GET_BI[FX]
returns an acpi_bi[fx] structure built by using information obtained
from a _BIF or a _BIX object found on the system. The revision number
field can be used to check which field is available. The acpiconf(8)
utility will show additional information if _BIX is available.
Although ABIs of ACPIIO_BATT_* were changed, the existing APIs for
userland utilities are not changed and the backward-compatible ABIs
are provided. This means that older versions of acpiconf(8) can also
work with the new kernel. The (union acpi_battery_ioctl_arg) was
padded to 256 byte long to avoid another ABI change in the future.
A _BIX object with its revision number >1 will be treated as
compatible with the rev.1 _BIX format.
Reviewed by: takawata
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23728
PR: 244118
Reported by: Francis Little <oggy at farscape.co.uk>
Tested by: Francis Little, Mark Millard <marklmi at yahoo.com>
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D23729
"Oops" - ln(1) is fine and dandy, but when you're using DESTDIR...it's not-
the path will almost certainly be invalid once the root you've just
installed to is relocated, perhaps to /.
Switch to install(1) using `-l rs` to calculate the relative symlink between
the two, which should work just fine in all cases.
MFC after: 1 week
buffer group.
This fixes a bug where congestion drops on port 1 of a T6 card would
incorrectly be counted as drops on port 0.
MFC after: 1 week
Sponsored by: Chelsio Communications
sys/arm/allwinner/clkng/aw_clk_mipi.c:144:6: error: misleading indentation; statement is not part of the previous 'if' [-Werror,-Wmisleading-indentation]
m++;
^
sys/arm/allwinner/clkng/aw_clk_mipi.c:142:5: note: previous statement is here
if (best == *fout)
^
Move the increment operations into the for loop headers instead.
Discussed with: manu
MFC after: 3 days
Each entry in ObsoleteFiles.inc adds to the time `make delete-old` and
friends take to run. Perl was removed from the FreeBSD base system a
very long time ago (FreeBSD 5); source updates have not been supported
from that version for years.
Perl was a single component responsible for thousands of entries so
provides significant benefit with little effort/investigation required.
We could still use a more comprehensive cleanup to remove old entries.
Also add an UPDATING note (with wordsmithing by imp) indicating that
`make delete-old` is required along each step of a source upgrade from
an old, unsupported release.
Discussed with: imp
Sponsored by: The FreeBSD Foundation
