It is unlikely, but possible, that an unrecognized or unsupported
relocation type is encountered while trying to load a kernel module. If
this occurs we should offer the symbol index as a hint to the user.
While here, fix some small style issues.
Reviewed by: markj, kib (amd64 part, in D26701)
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
We have a few shortcuts in the arm trap code to speed up obvious "must fail"
cases. In these situations, make sure that we fill in the "sig" and "code"
fields of the generated signal.
MFC after: 3 weeks
The hardware supports periods as long as 196 seconds[*] when using the
maximal prescaling of 72000 and maximum cycle count of 2^16.
But the code becomes incorrect when the period length approaches 1 second.
That's because of things like NS_PER_SEC / period.
[*] At the same time I must note that the KPI provides for maximum
period of about 4 seconds (2^32 nanoseconds).
MFC after: 2 weeks
On Ampere Altra systems, the sparse population of RAM within the
physical address space causes the vm_page_dump bitmap to be much
larger than necessary, increasing the size from ~8 Mib to > 2 Gib
(and overflowing `int` for the size).
Changing the page dump bitmap also changes the minidump file
format, so changes are also necessary in libkvm.
Reviewed by: jhb
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26131
These definitions were repeated by all architectures, with small
variations. Consolidate the common definitons in machine
independent code and use bitset(9) macros for manipulation. Many
opportunities for deduplication remain in the machine dependent
minidump logic. The only intended functional change is increasing
the bit index type to vm_pindex_t, allowing the indexing of pages
with address of 8 TiB and greater.
Reviewed by: kib, markj
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26129
OTG mode is not supported still. It's easy to do it as a one-off
detection, but the proper support requires continuous monitoring and
communicating the current state to the USB layer.
Also, fix phy0_route setting for H3. Remove duplicate register
definitions.
Tested on Orange Pi PC Plus with dr_mode="peripheral" using
hw.usb.template=3
umodem_load="YES"
Reviewed by: manu
MFC after: 5 weeks
Differential Revision: https://reviews.freebsd.org/D26348
One problem with the bus_space_read_N() and bus_space_write_N() family of
functions is that they provide no protection against exceptions which can
occur when no physical hardware or device responds to the read or write
cycles. In such a situation, the system typically would panic due to a
kernel-mode bus error. The bus_space_peek_N() and bus_space_poke_N() family
of functions provide a mechanism to handle these exceptions gracefully
without the risk of crashing the system.
Typical example is access to PCI(e) configuration space in bus enumeration
function on badly implemented PCI(e) root complexes (RK3399 or Neoverse
N1 N1SDP and/or access to PCI(e) register when device is in deep sleep state.
This commit adds a real implementation for arm64 only. The remaining
architectures have bus_space_peek()/bus_space_poke() emulated by using
bus_space_read()/bus_space_write() (without exception handling).
MFC after: 1 month
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D25371
that can be extended, but also ensure compile-time type checking. Refactor
common code out of arch-specific implementations. Move the mpr and mps
drivers to this new API. The template type remains visible to the consumer
so that it can be allocated on the stack, but should be considered opaque.
Fixes for Raspberry Pi 4B PCIe / USB:
- Pass through a DMA tag for the controller.
- In theory the controller can access the lower 3 GB, but testing found
that unreliable. OpenBSD also restricts DMA to the lowest 960 MiB.
- Rename some constants to be a bit more meaningful.
Submitted by: Robert Crowston, crowston at protonmail.com
Reviewed by: mkarels, outside reviewers
Differential Revision: https://reviews.freebsd.org/D26344
Allwinner USB DRD is based on the Mentor USB OTG controller, with a
different register layout and a few missing registers.
The code is by Andrew Turner (andrew).
Reviewed by: hselasky, manu
Obtained from: andrew
MFC after: 5 weeks
Differential Revision: https://reviews.freebsd.org/D5881
abs() takes a (signed) int as input.
Instead, it was used with unsigned 64-bit integers.
So, add and use a new helper function to calculate a difference between
two uint64_t-s.
Reviewed by: manu
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D26307
Currently we use a single bit to indicate whether the virtual page is
part of a superpage. To support a forthcoming implementation of
non-transparent 1GB superpages, it is useful to provide more detailed
information about large page sizes.
The change converts MINCORE_SUPER into a mask for MINCORE_PSIND(psind)
values, indicating a mapping of size psind, where psind is an index into
the pagesizes array returned by getpagesizes(3), which in turn comes
from the hw.pagesizes sysctl. MINCORE_PSIND(1) is equal to the old
value of MINCORE_SUPER.
For now, two bits are used to record the page size, permitting values
of MAXPAGESIZES up to 4.
Reviewed by: alc, kib
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D26238
This allows privileged userspace processes to find information about the
physical page backing a given mapping. It is useful in applications
such as DPDK which perform some of their own memory management.
Reviewed by: kib, jhb (previous version)
MFC after: 2 weeks
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D26237
devctl_notify_f isn't needed, so retire it. The flags argument is now
unused, so rather than keep it around, retire it. Convert all old
users of it to devctl_notify(). This path no longer sleeps, so is safe
to call from any context. Since it doesn't sleep, it doesn't need to
know if it is OK to sleep or not.
Reviewed by: markj@
Differential Revision: https://reviews.freebsd.org/D26140
For some unknown reason this seems to fix this function when we printf
the best variable. This isn't a delay problem as doing a printf without
it doesn't solve this problem.
This is way above my pay grade so add some printf that shouldn't be printed
in 99% of the case anyway.
Fix booting on most Allwinner boards as the mmc IP uses a NM clock.
Reported by: Alexander Mishin <mishin@mh.net.ru>
MFC after: 3 days
X-MFC-With: 363887
Currently, we parse notes for the values of ELF FreeBSD feature flags
and osrel. Knowing these values, or knowing that image does not carry
the note if pointers are NULL, is useful to decide which ABI variant
(brand) we want to activate for the image.
Right now this is only a plumbing change
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D25273
While here change type of some variables from long to int, it's sufficient.
Also, add length reporting to a couple of debug printfs.
MFC after: 3 weeks
In NECx the leading mark has length of 8T as opposed to 16T in NEC,
where T is 562.5 us. So, 4.5 ms.
Our threshold was set to 128 * 42.7 us (derived from the sampling
frequency of 3/128 MHz). So, ~5.5 ms.
The new threshold is set to AW_IR_L1_MIN. I think that's a good enough
lower bound for detecting the leading pulse.
Also, calculations of active_delay (which is activation delay) are fixed.
Previously they would be wrong if AW_IR_ACTIVE_T was anything but zero,
because the value was already bit-shifted.
Finally, I am not sure why the activation delay was divided by two when
calculating the initial pulse length. I have not found anything that
would explain or justify it. So, I removed that division.
MFC after: 3 weeks
These exist on the Raspberry Pi 3 and 4 and control and external IO
expander.
Reviewed by: manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25858
There are child nodes in the device tree, e.g. the Raspberry Pi firmware
GPIO device. Add support for this to be a bus so we can attach these
children.
Reviewed by: manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25848
The newer hardware revisions of the Raspberry Pi 4 removed the ability of
the VIA VL805 xhci controller to load its own firmware. Instead the
firmware must be installed at the appropriate time by the VideoCore
coprocessor.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25261
Re-implement clocks for these SoC by using now standard extres/clk framework.
This is necessary for future expansion of these. The new implementation
is (due to the size of the patch) only the initial (minimum) version.
It will be updated/expanded with a subsequent set of particular patches.
This patch is also not tested on OMAP4 based boards (BeagleBone),
so all possible issues should be (and will be) fixed by ASAP once
identified.
Submited by: Oskar Holmlund (oskar.holmlund@ohdata.se)
Differential Revision: https://reviews.freebsd.org/D25118
The Raspberry Pi GPIO config and state messages incorrectly return with
the tag length set to 0. We then check this value to have the response
flag set. Work around this by setting the response flag when setting the
GPIO config or state and this value is zero.
Sponsored by: Innovate UK
Use the new Raspberry Pi firmware driver in the cpufreq driver. It is
intended all drivers that need to interact with the firmware will move to
use the firmware driver, this is the first.
Reviewed by: manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25609
It will be needed by other eaarly drivers.
While here make the dependency of the mailbox formal with MODULE_DEPEND.
Reviewed by: manu
Sponsored by: Innovate UK
The firmware driver uses the mailbox driver to communicate with the
firmware. Make this a more formal dependency.
Reviewed by: manu
Sponsored by: Innovate UK
This will be needed before a future GPIO controller driver is added
as the later enables regulators that leave the SDHCI controller disabled.
Reviewed by: manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25834
The gate control bit offset was correctly specified, but AW_CLK_HAS_GATE
flag was not set.
Tested with (C)IR receiver on Orange Pi PC Plus.
Reviewed by: manu
MFC after: 1 week
This removes SCTP from in-tree kernel configuration files. Now, SCTP
can be enabled by simply loading the module, as discussed on
freebsd-net@.
Reviewed by: tuexen
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D25611
Module name (unlike of the of driver name) must be system wide unique.
Reported by: Mark Millard(bcm_pci), andrew(mvebu_gpio)
MFC with: r362954, r362385
Communicating with the Raspberry Pi firmware is currently handled by each
driver calling into the mbox driver, however the device tree is structured
such that they should be calling into a firmware driver.
Add a driver for this node with an interface to communicate to the firmware
via the mbox interface.
There is a sysctl to get the firmware revision. This is a unix date so can
be parsed with:
root@generic:~ # date -j -f '%s' sysctl -n dev.bcm2835_firmware.0.revision
Tue Nov 19 16:40:28 UTC 2019
Reviewed by: manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D25572
This adds support for the Broadcom bcm2711 PCI express controller, found
on the Raspberry Pi 4 (aka the bcm2838 SoC). The driver has only been
developed against the soldered-on VIA XHCI controller and not tested
with other end points.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25068
- Add CCM driver and clocks implementations for i.MX 8M
- Add GPC driver for iMX8
- Add clock tree for i.MX 8M Quad
- Add clocks support and new compat strings (where required) for existing i.MX 6 UART, I2C, and GPIO drivers
- Enable aarch64-compatible drivers form i.MX 6 in arm64 GENERIC kernel config
- Add dtb/imx8 kernel module with DTBs for Nitrogen8M and iMX8MQ EVK
With this patch both Nitrogen8M and iMX8MQ EVK boot with NFS root up to multiuser login prompt
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D25274
The Raspbery Pi computers do not properly implement PSCI. The canonical
way to reset them is to set a watchdog timer and allow it to expire.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25268
It turns out relocating the symbol table itself can cause issues, like fbt
crashing because it applies the offsets to the kernel twice.
This had been previously brought up in rS333447 when the stoffs hack was
added, but I had been unaware of this and reimplemented symtab relocation.
Instead of relocating the symbol table, keep track of the relocation base
in ddb, so the ddb symbols behave like the kernel linker-provided symbols.
This is intended to be NFC on platforms other than PowerPC, which do not
use fully relocatable kernels. (The relbase will always be 0)
* Remove the rest of the stoffs hack.
* Remove my half-baked displace_symbol_table() function.
* Extend ddb initialization to cope with having a relocation offset on the
kernel symbol table.
* Fix my kernel-as-initrd hack to work with booke64 by using a temporary
mapping to access the data.
* Fix another instance of __powerpc__ that is actually RELOCATABLE_KERNEL.
* Change the behavior or X_db_symbol_values to apply the relocation base
when updating valp, to match link_elf_symbol_values() behavior.
Reviewed by: jhibbits
Sponsored by: Tag1 Consulting, Inc.
Differential Revision: https://reviews.freebsd.org/D25223
The submitter notes that the bcm2835_cpufreq driver really just needs the
rpi4 compat string added to it; powerd subsequently works and the dev.cpu.0
sysctl values look sane and can be successfully manipulated.
Submitted by: James Mintram <me@jamesrm.com>
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D25349
By using DWC TRM terminology, normal descriptor format should be named
extended and alternate descriptor format should be named normal.
Should not been functional change.
MFC after: 4 weeks
The AXI bridge is different between ARMADA 38x and 8K, and both platforms
needs specific setup to mitigate HW issues with accessing RTC registers.
MFC after: 2 weeks
Big endian and armv4 mean that we are now down to only two supported
variants. A future change will use MACHINE_ARCH in assembly which
does not support C-style string concatentation and thus needs
MACHINE_ARCH defined as a single string.
Reviewed by: imp
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D25211
- Configure ipu1_di0 tob e sourced from the VIDEO_PLL(PLL5) and hardcode
frequency to (455000000/3)Mhz. This value, further divided, can yield
frequencies close enough to support 1080p, 720p, 1024x768, and 640x480
modes. This is not ideal but it's an improvement comparing to the only
hardcoded 1024x768 mode.
- Fix memory leaks if attach method failed
- Print EDID when -v passed to the kernel
In the recent dts sync the name of the aips-bus@ changed to bus@. Reflect
this change and add an additional OF_finddevice in fix_fdt_interrupt_data()
and in fix_fdt_iomuxc_data() with bus@ only. Iow, keep the old naming for
compatibility.
Discussed with: ian@
The trampoline code used for loading gzipped a.out kernels on arm was
removed in r350436. A portion of this code allowed for DDB to find the
symbol tables when booting without loader(8), and some of this was
untouched in the removal. Remove it now.
Differential Revision: https://reviews.freebsd.org/D24950
r347343 split generic xhci driver into three files.
Include generic_xhci_fdt.c when building kernel for Armada SoCs.
This brings back XHCI support on these platforms and also
others, which use GENERIC config.
Submitted by: Kornel Duleba
Obtained from: Semihalf
MFC after: 1 week
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D24944
This reapplies logical r360944 and r360946 (reverting r360955), with fixed
copystr() stand-in replacement macro. Eventually the goal is to convert
consumers and kill the macro, but for a first step it helps if the macro is
correct.
Prior commit message:
Unlike the other copy*() functions, it does not serve to copy from one
address space to another or protect against potential faults. It's just
an older incarnation of the now-more-common strlcpy().
Add a coccinelle script to tools/ which can be used to mechanically
convert existing instances where replacement with strlcpy is trivial.
In the two cases which matched, fuse_vfsops.c and union_vfsops.c, the
code was further refactored manually to simplify.
Replace the declaration of copystr() in systm.h with a small macro
wrapper around strlcpy (with correction from brooks@ -- thanks).
Remove N redundant MI implementations of copystr. For MIPS, this
entailed inlining the assembler copystr into the only consumer,
copyinstr, and making the latter a leaf function.
Reviewed by: jhb (earlier version)
Discussed with: brooks (thanks!)
Differential Revision: https://reviews.freebsd.org/D24672
NXP LS1046A contains I2C controller compatible with Vybrid VF610.
Existing Vybrid MVF600 driver can be used to support it. For that purpose
declare driver as ofw_iicbus and add methods associated with ofw_iicbus.
For VF610 add dynamic clock prescaler calculation using clock information
from clock driver and clock frequency requested in device tree.
On the occasion add detach function and add additional error handling
in i2c_attach function.
Submitted by: Dawid Gorecki <dgr@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D24361
hardware, the registers appear like there's two cores, but the second
core does not work, so base the number of cores upon the chip id.
Tested on a XC7Z007S.
also, previous commit was suppose to be D14429.
Submitted by: Thomas Skibo
Differential Revision: https://reviews.freebsd.org/D14429
Unlike the other copy*() functions, it does not serve to copy from one
address space to another or protect against potential faults. It's just
an older incarnation of the now-more-common strlcpy().
Add a coccinelle script to tools/ which can be used to mechanically
convert existing instances where replacement with strlcpy is trivial.
In the two cases which matched, fuse_vfsops.c and union_vfsops.c, the
code was further refactored manually to simplify.
Replace the declaration of copystr() in systm.h with a small macro
wrapper around strlcpy.
Remove N redundant MI implementations of copystr. For MIPS, this
entailed inlining the assembler copystr into the only consumer,
copyinstr, and making the latter a leaf function.
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D24672
This has the same reasoning as described in r357048.
Remove a stray declaration while here.
Reported and tested by: trasz
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
The arm_physmem interface found in arm's MD code provides a convenient
set of routines for adding/excluding physical memory regions and
initializing important kernel globals such as Maxmem, realmem,
phys_avail[], and dump_avail[]. It is especially convenient for FDT
systems, since we can use FDT parsing functions and pass the result
directly to one of these physmem routines. This interface is already in
use on arm and arm64, and can be used to simplify this early
initialization on RISC-V as well.
This requires only a couple trivial changes:
- Move arm_physmem_kernel_addr to arm/machdep.c. It is unused on arm64,
and manipulated entirely in arm MD code.
- Convert arm32_btop/arm64_btop to atop. This is equivalently defined
on all architectures.
- Drop the "arm" prefix.
Reviewed by: manu, emaste ("looks reasonable")
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D24153
Name each pcib driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/pcib from kernel; already loaded from kernel
While here, add a makefile in sys/modules/allwinner so it is built.
Also add the PNP info so devmatch will load this module automatically.
MFC after: 1 month
The upstream DTS now include the thermal device node and the SID
calibration entry.
Update our driver to cope with this change and remove the DTB
overlays that aren't needed anymore.
MFC after: 2 months
X-MFC-With: r359934
The fdt properties are now parsed via the help of mmc_fdt_helper functions.
This also adds card detection.
Note that on some boards (like the Pine64) card detection is broken due to
a missing resistor on the cd pin.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23268
Honor ti,pmic-shutdown-controller option in DTS
Tested on stable r359316 @ Sleep mode on custom hw, Power off on BBB and PB
OFF bit [1] in status register control the pmic behaviour when PWR_EN pin
is pulled low.
On most AM335x hardware [beaglebone *] the desired behaviour are in fact
power off due to some hardware designs - read more in the comments around
pmic in sys/gnu/dts/arm/am335x-bone-common.dtsi
This patch let the device-tree decide with ti,pmic-shutdown-controller[2]
the state of off bit in status register.
[1] 8.6.12 table 12 http://www.ti.com/lit/ds/symlink/tps65217.pdf
[2] Documentation/devicetree/bindings/regulator/tps65217.txt
PR: 245159
Submitted by: Oskar Holmlund <oskar.holmlund@ohdata.se>
MFC after: 2 weeks
Modern debuggers and process tracers use ptrace() rather than procfs
for debugging. ptrace() has a supserset of functionality available
via procfs and new debugging features are only added to ptrace().
While the two debugging services share some fields in struct proc,
they each use dedicated fields and separate code. This results in
extra complexity to support a feature that hasn't been enabled in the
default install for several years.
PR: 244939 (exp-run)
Reviewed by: kib, mjg (earlier version)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D23837
The goal of this change is to make the atomic_load_acq_{8,16},
atomic_testandset{,_acq}_long, and atomic_testandclear_long primitives
available in MI-namespace.
The second goal is to get this draft out of my local tree, as anything that
requires a full tinderbox is a big burden out of tree. MD specifics can be
refined individually afterwards.
The generic implementations may not be ideal for your architecture; feel
free to implement better versions. If no subword_atomic definitions are
needed, the include can be removed from your arch's machine/atomic.h.
Generic definitions are guarded by defined macros of the same name. To
avoid picking up conflicting generic definitions, some macro defines are
added to various MD machine/atomic.h to register an existing implementation.
Include _atomic_subword.h in arm and arm64 machine/atomic.h.
For some odd reason, KCSAN only generates some versions of primitives.
Generate the _acq variants of atomic_load.*_8, atomic_load.*_16, and
atomic_testandset.*_long. There are other questionably disabled primitives,
but I didn't run into them, so I left them alone. KCSAN is only built for
amd64 in tinderbox for now.
Add atomic_subword implementations of atomic_load_acq_{8,16} implemented
using masking and atomic_load_acq_32.
Add generic atomic_subword implementations of atomic_testandset_long(),
atomic_testandclear_long(), and atomic_testandset_acq_long(), using
atomic_fcmpset_long() and atomic_fcmpset_acq_long().
On x86, add atomic_testandset_acq_long as an alias for
atomic_testandset_long.
Reviewed by: kevans, rlibby (previous versions both)
Differential Revision: https://reviews.freebsd.org/D22963
As defined in atomic(9) and implemented on other architectures, the
atomic(9) functions all act on unsigned pointers and types. Prior to this
revision, arm implemented some atomic(9) 'long' sized routines with correct
unsigned type, but others were incorrectly signed.
Reviewed by: tinderbox
Sponsored by: Dell EMC Isilon
When I implemented MD DYNAMIC parsing, I was originally passing a
linker_file_t so that the MD code could relocate pointers.
However, it turns out this isn't even filled in until later, so it was
always 0.
Just pass the load base (ef->address) directly, as that's really the only
thing we were interested in in the first place.
This fixes a crash on RB800 where it was trying to write to an unmapped
address when updating the GOT.
Reviewed by: jhibbits
Sponsored by: Tag1 Consulting, Inc.
Differential Revision: https://reviews.freebsd.org/D24105
sys/arm/arm/identcpu-v6.c:227:5: error: misleading indentation; statement is not part of the previous 'if' [-Werror,-Wmisleading-indentation]
if (val & CPUV7_CT_CTYPE_RA)
^
sys/arm/arm/identcpu-v6.c:225:4: note: previous statement is here
if (val & CPUV7_CT_CTYPE_WB)
^
This was due to an accidentally inserted tab before the if statement.
MFC after: 3 days
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Approved by: kib (mentor, blanket)
Differential Revision: https://reviews.freebsd.org/D23635
sys/arm/allwinner/clkng/aw_clk_mipi.c:144:6: error: misleading indentation; statement is not part of the previous 'if' [-Werror,-Wmisleading-indentation]
m++;
^
sys/arm/allwinner/clkng/aw_clk_mipi.c:142:5: note: previous statement is here
if (best == *fout)
^
Move the increment operations into the for loop headers instead.
Discussed with: manu
MFC after: 3 days
sys/arm/allwinner/aw_cir.c:208:41: error: converting the result of '<<' to a boolean; did you mean '((1 & 255) << 23) != 0'? [-Werror,-Wint-in-bool-context]
active_delay = (AW_IR_ACTIVE_T + 1) * (AW_IR_ACTIVE_T_C ? 128 : 1);
^
sys/arm/allwinner/aw_cir.c:130:39: note: expanded from macro 'AW_IR_ACTIVE_T_C'
#define AW_IR_ACTIVE_T_C ((1 & 0xff) << 23)
^
Add the != 0 part to indicate that we indeed want to compare against
zero.
This reverts r177661. The change is no longer very useful since
out-of-tree KLDs will be built to target SMP kernels anyway. Moveover
it breaks the KBI in !SMP builds since cpuset_t's layout depends on the
value of MAXCPU, and several kernel interfaces, notably
smp_rendezvous_cpus(), take a cpuset_t as a parameter.
PR: 243711
Reviewed by: jhb, kib
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23512
Submitted by: Bora Özarslan <borako.ozarslan@gmail.com>
Submitted by: Yang Wang <2333@outlook.jp>
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19917
Now that armv5 is gone, we no longer need multiple LINT files. Kill
the odd-ball support here. From now on, we just have LINT built from
notes like all the other platforms. Keep the removal of LINT-V5/7
to remove stale files for a while still..
After r355784 the td_oncpu field is no longer synchronized by the thread
lock, so the stack capture interrupt cannot be delievered precisely.
Fix this using a loop which drops the thread lock and restarts if the
wrong thread was sampled from the stack capture interrupt handler.
Change the implementation to use a regular interrupt instead of an NMI.
Now that we drop the thread lock, there is no advantage to the latter.
Simplify the KPIs. Remove stack_save_td_running() and add a return
value to stack_save_td(). On platforms that do not support stack
capture of running threads, stack_save_td() returns EOPNOTSUPP. If the
target thread is running in user mode, stack_save_td() returns EBUSY.
Reviewed by: kib
Reported by: mjg, pho
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D23355
This is a qspi driver for the Xilinx Zynq-7000 chip.
It could be useful for anyone wanting to boot a system from flash memory
instead of SD cards.
Submitted by: Thomas Skibo (thomasskibo@yahoo.com)
Differential Revision: https://reviews.freebsd.org/D14698
Not all pins in Allwinner have interrupts support so we rely
on the padconf data to add the proper caps when pin_getcaps is called.
The pin is switch to the specific "eint" function during setup_intr and
switched back to its old function in teardown_intr.
Only INTR_MAP_DATA_GPIO is supported for now.
MFC after: 1 month
Add a eint_bank member to the allwinner_pins structure.
On Allwinner SoCs not all pins can do interrupt.
Older SoC (A10/A13 and A20) there is a maximum number of interrupts
set to 32 and all the configuration is done in the same registers.
While on "newer" SoCs (>=A31) interrupts registers are splitted per
pin bank (i.e. all interrupts available in bank B will be configured
with a sets of registers and the one in bank G in another set).
While here set the names to all interrupts function to
pX_eintY where X is the bank name and Y the interrupt number.
To whom ever in the future look at the H5 manual and notice that the bank F
have interrupts support : This isn't true, trust me.
MFC after: 1 month
r355473 vastly improved the readability and cleanliness of these Makefiles.
Every single one of them follows the same pattern and duplicates the exact
same logic.
Now that we have GENERATED/SRCS, split SRCS up into the two parameters we'll
use for ${MAKESYSCALLS} rather than assuming a specific ordering of SRCS and
include a common sysent.mk to handle the rest. This makes it less tedious to
make sweeping changes.
Some default values are provided for GENERATED/SYSENT_*; almost all of these
just use a 'syscalls.master' and 'syscalls.conf' in cwd, and they all use
effectively the same filenames with an arbitrary prefix. Most ABIs will be
able to get away with just setting GENERATED_PREFIX and including
^/sys/conf/sysent.mk, while others only need light additions. kern/Makefile
is the notable exception, as it doesn't take a SYSENT_CONF and the generated
files are spread out between ^/sys/kern and ^/sys/sys, but it otherwise fits
the pattern enough to use the common version.
Reviewed by: brooks, imp
Nice!: emaste
Differential Revision: https://reviews.freebsd.org/D23197
Raspberry Pi are all over the board, and the reality is that there's no harm
in including all of the definitions by default but plenty of harm in the
current situation. This change is safe because we match a definition by root
/compatible in the FDT, so there will be no false-positives because of it.
The main array of definitions grows, but it's only walked exactly once to
determine which we need to use.
The target-supply regulator is optional so don't fail if it's not present.
While here disable the clock on detach.
MFC after: 2 weeks
X-MFC-With: 356600
Each GPIO bank is powered by a different pin and so can be powered at different
voltage from different regulators.
Add a new config that now hold the pinmux data and the banks available on each
SoCs.
Since the aw_gpio driver being also the pinmux one it's attached before the PMIC
so add a config_intrhook_oneshot function that will enable the needed regulators
when the system is fully functional.
MFC after: 2 weeks
This method will set the desired voltaged based on values in the DTS.
It will not enable the regulator, this is the job of either a consumer
or regnode_set_constraint SYSINIT if the regulator is boot_on or always_on.
MFC after: 2 weeks
When either makesyscalls.lua or syscalls.master changes, all of the
${GENERATED} targets are now out-of-date. With make jobs > 1, this means we
will run the makesyscalls script in parallel for the same ABI, generating
the same set of output files.
Prior to r356603 , there is a large window for interlacing output for some
of the generated files that we were generating in-place rather than staging
in a temp dir. After that, we still should't need to run the script more
than once per-ABI as the first invocation should update all of them. Add
.ORDER to do so cleanly.
Reviewed by: brooks
Discussed with: sjg
Differential Revision: https://reviews.freebsd.org/D23099
This regulator is marked regulator-boot-on, but it will get shutdown if it's
not actually used/enabled by a driver. This should fix sata on the
cubieboard{1,2}.
Reported by: Ray White @ UWaterloo
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D23112
- Garbage collect UMA_ZONE_PAGEABLE & UMA_ZONE_STATIC.
- Move flag VTOSLAB from public to private.
- Introduce public NOTPAGE flag and make HASH private.
- Introduce public NOTOUCH flag and make OFFPAGE private.
- Update man page.
The net effect of this should be to make the contract with clients more
clear. Clients should choose constraints, UMA will figure out how to
implement them. This also breaks the confusing double meaning of
OFFPAGE.
Reviewed by: jeff, markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D23016
This is needed when the driver is compiled into the kernel.
When compiled as a module this will be called from another
code path as we also depend on ofw_spibus.
MFC after: 1 week
This brings arm into line with how every other arch does it. For some
reason, only arm lacked a definition of a symbol named kernbase in its
locore.S file(s) for use in its ldscript.arm file. Needlessly different
means harder to maintain.
Using a common symbol name also eases work in progress on a script to help
generate arm and arm64 kernels packaged in various ways (like with a header
blob needed for a bootloader prepended to the kernel file).
Due to clang and LLD's tendency to use a PLT for builtins, and as they
don't have full support for EABI, we sometimes have to deal with a PLT in
.ko files in a clang-built kernel.
As such, augment the in-kernel linker to support jump table processing.
As there is no particular reason to support lazy binding in kernel modules,
only implement Secure-PLT immediate binding.
As part of these changes, add elf_cpu_parse_dynamic() to the MD API of the
in-kernel linker (except on platforms that use raw object files.)
The new function will allow MD code to act on MD tags in _DYNAMIC.
Use this new function in the PowerPC MD code to ensure BSS-PLT modules using
PLT will be rejected during insertion, and to poison the runtime resolver to
ensure we get a clear panic reason if a call is made to the resolver.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D22608
off the stack, initialized to default values, and then filled in with
driver-specific values, all without having to worry about the numerous
other fields in the tag. The resulting template is then passed into
busdma and the normal opaque tag object created. See the man page for
details on how to initialize a template.
Templates do not support tag filters. Filters have been broken for many
years, and only existed for an ancient make/model of hardware that had a
quirky DMA engine. Instead of breaking the ABI/API and changing the
arugment signature of bus_dma_tag_create() to remove the filter arguments,
templates allow us to ignore them, and also significantly reduce the
complexity of creating and managing tags.
Reviewed by: imp, kib
Differential Revision: https://reviews.freebsd.org/D22906
r356043 missed a couple of references in machdep parts... arguably, these
lines could probably be dropped as the softc is likely still zero'd at this
point.
Pointy hat: kevans
As far as I can tell, these are an artifact of times when linker sets
couldn't be empty, otherwise the kernel build would fail due to unresolved
symbols. hselasky fixed this in r268138, and I've audited the kbd portions
to make sure nothing would blow up due to the empty linker set and
successfully compiled+ran a kernel with no keyboard support at all.
Kill them off now since they're no longer required.
MFC after: 1 week
I've opted for just duplicating the two entries needed for this, rather than
writing any other mechanism for maintaining two root compat entries to map
to one config, for simplicity. We'll eventually declare these legacy DTB
unsupported, but let's not do that yet while there's no real burden.
We use armv7/GENERIC for the RPI2 images. The original RPI2 is actually a
32-bit BCM2836, but v1.2 was upgraded to the 64-bit BCM2837. The project
continues to provide the RPI2 image as armv7, as it's the lowest common
denominator of the two. Historically, we've just kind of implicitly
acknowledged this by including some bcm2837 bits on a SOC_BCM2836 kernel
config -- this worked until r354875 added code that actually cared.
Acknowledge formally that BCM2837 is valid in arm32.
This name is inconsistent with the other BCM* SOC on !arm64 for two reasons:
1. It's a pre-existing option on arm64, and
2. the naming convention on arm/ should've arguably changed to include BRCM
#1 seems to be a convincing enough argument to maintain the existing name
for it.
fix an assert violation introduced in r355784. Without this spinlock_exit()
may see owepreempt and switch before reducing the spinlock count. amd64
had been optimized to do a single critical enter/exit regardless of the
number of spinlocks which avoided the problem and this optimization had
not been applied elsewhere.
Reported by: emaste
Suggested by: rlibby
Discussed with: jhb, rlibby
Tested by: manu (arm64)
These invocations were directly calling enkbd_diag(), rather than
indirection back through kbdd_diag/kbdsw. While they're functionally
equivent, invoking kbdd_diag where feasible (i.e. not in a diag
implementation) makes it easier to visually identify locking needs in these
other drivers.
The arm kernel stack unwinder has apparently never been able to unwind when
the path of execution leads through a kernel module. There was code that
tried to handle modules by looking for the unwind data in them, but it did
so by trying to find symbols which have never existed in arm kernel
modules. That caused the unwind code to panic, and because part of panic
handling calls into the unwind code, that just created a recursion loop.
Locating the unwind data in a loaded module requires accessing the Elf
section headers to find the SHT_ARM_EXIDX section. For preloaded modules
those headers are present in a metadata blob. For dynamically loaded
modules, the headers are present only while the loading is in progress; the
memory is freed once the module is ready to use. For that reason, there is
new code in kern/link_elf.c, wrapped in #ifdef __arm__, to extract the
unwind info while the headers are loaded. The values are saved into new
fields in the linker_file structure which are also conditional on __arm__.
In arm/unwind.c there is new code to locally cache the per-module info
needed to find the unwind tables. The local cache is crafted for lockless
read access, because the unwind code often needs to run in context where
sleeping is not allowed. A large comment block describes the local cache
list, so I won't repeat it all here.
