Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
locks up in make buildworld.
You need to follow the mips wiki for building
the nfs partition and setup things to mount there
(in the conf and in your bootp setup).
the intention of having two ttys pointing to the same cfe console device was.
Also we were not initializing the output[] array passed in as input to
tty_makedev() so one name of the ttys was garbage.
Fix the code that calls cfe_write() to deal with the case where only a partial
buffer is written out.
cfe_cngetc() needs to return if there is no character available as input.
If we don't do this then the cfe_timeout() function will spin forever
because cfe_cngetc() will only ever return if there is valid input.
Approved by: imp (mentor)
This is a workaround for the fact that the CFE is compiled as a 64-bit
application and therefore sets the SR_KX bit every time we call into
it (for e.g. console).
A TLB miss for any address above 0xc0000000 with the SR_KX bit set will
end up at the XTLB exception vector. We workaround this by copying the
standard TLB handler at the XTLB exception vector.
Approved by: imp (mentor)
through fork_trampoline.
This was caused because we were clearing the SR_INT_IE and setting
SR_EXL bits of the status register at the same time. This meant
that if an interrupt happened while this MTC0 was making its way
through the pipeline the exception processing would see the
status register with SR_EXL bit set. This in turn would mean that
the COP_0_EXC_PC would not be updated so the return from exception
would be to an incorrect address.
It is easy to verify this fix by a program that forks in a loop
and the child just exits:
while (1) {
pid_t pid = vfork();
if (pid == 0)
_exit(0);
if (pid != -1)
waitpid(pid, NULL, 0);
}
Also remove two instances where we set SR_EXL bit gratuitously in exception.S.
Approved by: imp (mentor)
obio. Take advantage of the fact that obio only really supports uart
at the moment to use the uart bus tag always for IOPORT allocations.
# this needs to be redone to conform to FreeBSD standards and allow for
# additional drivers for SoC hardware to attach
in the pcb at the td_lock offset, rather than in the struct thread at
the td_lock offset. And we were storing a pointer to the old thread
rather than to the mutex. Why this didn't always kill us, I'll never
know.
Fix an obsolete comment and update the prototype in the comments.
Also note what variables are in what registers since this function is
a little complex...
neel@ found this problem and proposed this fix. This cures a number
of different problem reports out there, and gets us booting octeon to
the login prompt...
Submitted by: neel@
Reviewed by: rrs@, gonzo@
where the type is 32-bit. ZFS can handle 64-bit timestamp internally
but zfs_setattr() would check if the time value can fit, we change the
checking macros to match 64-bit timestamp if the platform supports it.
This change has some downsides like, while you can import zfs on 32-bit
platforms, the timestamp would overflow if they are out of the range.
This fixes the Y2.038K issue on platforms using 64-bit timestamps.
Reviewed by: pjd
MFC after: 1 month
symbols resolving in DDB
- When zeroing .bss/.sbss do not round end address to page boundary,
it's not neccessary and might destroy data pased by trampoline or
boot loader
ifmultiaddr structures' reference to the parent interface, unless the parent
interface is really detaching. While here, program only link layer multicast
filters to a wlan's hardware parent interface.
PR: kern/142391, kern/142392
Reviewed by: sam, rpaolo, bms
MFC after: 1 week
In the current code, the locking is completely broken and may lead
easilly to deadlocks. Fix it by using the proc_mtx, linked to the
suspending thread, as lock for the operation. Keep using the
thread_lock for setting and reading the flag even if it is not entirely
necessary (atomic ops may do it as well, but this way the code is more
readable).
- Fix a deadlock within kthread_suspend().
The suspender should not sleep on a different channel wrt the suspended
thread, or, otherwise, the awaker should wakeup both. Uniform the
interface to what the kproc_* counterparts do (sleeping on the same
channel).
- Change the kthread_suspend_check() prototype.
kthread_suspend_check() always assumes curthread and must only refer to
it, so skip the thread pointer as it may be easilly mistaken.
If curthread is not a kthread, the system will panic.
In collabouration with: jhb
Tested by: Giovanni Trematerra
<giovanni dot trematerra at gmail dot com>
MFC: 2 weeks
available for use. All data below this address considered to be used
by kernel. Along with kernel own data it might be symbol tables
prepeared by trampoline code, boot loader service data passed for
further analysis by kernel, etc... By default kernel_kseg0_end points
to the end of loaded kernel.
- Introduce mips_postboot_fixup function. It checks for symbol information
copied by ELF trampoline and passes it to KDB
so on architectures with strict alignment requirements we can't just simply
cast the latter to the former but need to copy it bytewise instead.
PR: 143010
MFC after: 3 days
For PT_TO_SCE stop that stops the ptraced process upon syscall entry,
syscall arguments are collected before ptracestop() is called. As a
consequence, debugger cannot modify syscall or its arguments.
In syscall(), reread syscall number and arguments after ptracestop(),
if debugger modified anything in the process environment. Since procfs
stopevent requires number of syscall arguments in p_xstat, this cannot
be solved by moving stop/trace point before argument fetching.
Move the code to read arguments into separate function
fetch_syscall_args() to avoid code duplication. Note that ktrace point
for modified syscall is intentionally recorded twice, once with original
arguments, and second time with the arguments set by debugger.
PT_TO_SCX stop is executed after cpu_syscall_set_retval() already.
Reviewed by: kib
frontend uses the same uPD7210 backend as the pcii ISA frontend, so
the backend has to cope with both situations.
Also, hide the first printf in pcii_probe (address mismatch) behind
bootverbose as the ISA bus parent tries to probe all configured ISA
devices against each driver, so a the console has been cluttered with
this message for a bunch of unrelated driver probes.
MFC after: 3 days
