1. architecture-specific files
2. long double format-specific files
3. bsdsrc
4. src
5. man
The original order was virtually the opposite of this.
This should not cause any functional changes at this time. The
difference is only significant when one wants to override, say, a
generic foo.c with a more specialized foo.c (as opposed to foo.S).
and handle NIC hardware watchdog resets.
- remove buggy code at the top of mxge_tick() which tried
to detect a race which is already detected in the kernel's
callout code.
- move callout_stop() and callout_reset() into mxge_close()
mxge_open() rather than doing the callout manipulation
all over the place.
- use callout_drain(), rather than callout_stop() to prevent
a potential race between mxge_tick() and mxge_detach()
which could lead to softclock using a destroyed mutex
- restructure the mxge_tick() and mxge_watchdog_reset()
routines to avoid resetting a callout, and then
immediately stopping it if the watchdog reset routine
is called, and fails.
- enable the driver to handle NIC hardware watchdog
resets by restoring the NIC's PCI config space, which is
lost when the NIC hardware watchdog triggers.
Reviewed by: jhb (previus version)
sanity check by invoking "pwd_mkdb -C". However, if this failed it
silently returned success. Fix this so it fails the update operation
instead.
MFC after: 1 week
to allow them to do a "clean" shutdown.
I purposely avoided making changes to network-related stuff since the
system shutting down is pretty conclusive, and there may be complicated
dependencies on the network that I would rather not try to unravel.
I also skipped kerberos-related stuff for the reasons above, and
because I have no way to test it.
The tcsetattr() routine already converts the TCSA* arguments to their
respective TIOCSETA* ioctl's in the C library. There is no need to have
these definitions inside the kernel.
Approved by: philip (mentor, implicit)
I think one of the reasons why we have so many conflicts in the TTY
ioctl category, is because the ioctl's aren't ordered logically. This
commit only sorts them by number. The comments may still be inaccurate.
Approved by: philip (mentor)
When I ported most applications away from <sgtty.h>, I noticed none of
them were actually using these definitions. I kept them in place,
because I didn't want to touch tools like pstat(8) and stty(1).
In preparation for the MPSAFE TTY layer, remove these definitions. This
doesn't have any impact with respect to binary compatibility (see
tty_conf.c).
We couldn now add an #error to <sys/ioctl_compat.h> when included
outside the kernel. Unfortunately, kdump's mkioctls includes this file
unconditionally.
Approved by: philip (mentor)
vr(4) overhauling(r177050).
It seems that filtering multicast addresses with multicast CAM
entries require accessing 'CAM enable bit' for each CAM entry.
Subsequent accessing multicast CAM control register without
toggling the 'CAM enable bit' seem to no effects.
In order to fix that separate CAM setup from CAM mask configuration
and CAM entry modification. While I'm here add VLAN CAM filtering
feature which will be enabled in future(FreeBSD now can receive
VLAN id insertion/removal event from vlan(4) on the fly).
For VT6105M hardware, explicitly disable VLAN hardware tag
insertion/stripping and enable VLAN CAM filtering for VLAN id 0.
This shall make non-VLAN frames set VR_RXSTAT_VIDHIT bit in Rx
status word.
Added multicast/VLAN CAM address definition to header file.
PR: kern/125010, kern/125024
MFC after: 1 week
years. All datasheet I have indicates the bit 15 is the
VR_RXSTAT_RX_OK. The bit 14 is reserved for all Rhine family
except VT6105M. VT6105M uses that bit to indicate a VLAN frame
with matching CAM VLAN id.
Use the VR_RXSTAT_RX_OK instead of VR_RXSTAT_RXERR when vr(4)
checks the validity of received frame.
This should fix occasional dropping frames on VT6105M.
Tested by: Goran Lowkrantz ( goran.lowkrantz at ismobile dot com )
MFC after: 1 week
completes the move to a fully parallel UDP transmit path by using
global read, rather than write, locking of inpcbinfo in further
semi-connected cases:
- Add macros to allow try-locking of inpcb and inpcbinfo.
- Always acquire an incpcb read lock in udp_output(), which stablizes the
local inpcb address and port bindings in order to determine what further
locking is required:
- If the inpcb is currently not bound (at all) and are implicitly
connecting, we require inpcbinfo and inpcb write locks, so drop the
read lock and re-acquire.
- If the inpcb is bound for at least one of the port or address, but an
explicit source or destination is requested, trylock the inpcbinfo
lock, and if that fails, drop the inpcb lock, lock the global lock,
and relock the inpcb lock.
- Otherwise, no further locking is required (common case).
- Update comments.
In practice, this means that the vast majority of consumers of UDP sockets
will not acquire any exclusive locks at the socket or UDP levels of the
network stack. This leads to a marked performance improvement in several
important workloads, including BIND, nsd, and memcached over UDP, as well
as significant improvements in pps microbenchmarks.
The plan is to MFC all of the rwlock changes to RELENG_7 once they have
settled for a weeks in the tree.
Tested by: ps, kris (older revision), bde
MFC after: 3 weeks
This change removes the requirement that an ACL contain no ACL_USER
entries with a uid the same as those of a file, or ACL_GROUP entries
with a gid the same as those of a file. This requirement is not in the
specification, and not enforced by the kernel's ACL implementation.
Reported by: Iustin Pop <iusty at k1024 dot org>
MFC after: 1 week
The uart(4) driver has the advantage of supporting a wider variety of
hardware on a greater amount of platforms. This driver has already been
the standard on platforms such as ia64, powerpc and sparc64.
I've decided not to change anything on pc98. I'd rather let people from
the pc98 team look at this.
Approved by: philip (mentor), marcel
set MNT_UPDATE in fsflags, and delete the
"update" option from the global mount options.
MNT_UPDATE is a command, and not a property of a mount
that should persist after the command is executed.
We need to do similar things for MNT_FORCE and MNT_RELOAD.
All mount flags are prefixed by MNT_..... it would
be nice if flags which were commands were named differently
from flags which are persistent properties of a mount.
This was not such a big deal in the pre-nmount() days,
but with nmount() it is more important.
Requested by: yar
MFC after: 2 weeks
