The UEFI loader on the 10.1 release install disk (disc1) modifies an
existing EFI_DEVICE_PATH_PROTOCOL instance in an apparent attempt to
truncate the device path. In doing so it creates an invalid device
path.
Perform the equivalent action without modification of structures
allocated by firmware.
PR: 197641
MFC After: 1 week
Submitted by: Chris Ruffin <chris.ruffin@intel.com>
Place sched_random nearer to where it's first used: moving the
code nearer to where it is used makes the code easier to read
and we can reduce the initial "#ifdef SMP" island.
Reword a little the comment and clean some whitespaces
while here.
The 6205 (Taylor Peak) in the Lenovo X230 works fine in 5GHz 11a and 11n HT20,
but not 11n HT40. The NIC goes RX deaf the moment HT40 is configured.
It's so RX deaf that it doesn't even hear beacons and the firmware sends
"BEACON MISS" events. That's pretty deaf.
I tried configuring up the HT40 flags in monitor mode and it worked - so
I assumed that doing the transition from 20 -> 40MHz channel configuration
when going auth->assoc (ie, after the NIC has been partially configured)
is a problem.
So for now, let's just always set them if they're available.
Tested:
* Intel 5300, STA mode, 5GHz HT/40 AP; 2GHz HT/20 AP
* Intel 6205, STA mode, 5GHz HT/40, HT20, 11a AP; 2GHz HT/20 AP
This was pointed out to me by coworkers trying to use FreeBSD-HEAD
in the office on their Thinkpad T420p laptops.
TODO:
* I don't like how the HT40 flags are configured - the whole interop/
protection config should be re-checked. Notably, I think curhtprotmode
is 0 in a lot of cases, which means "no interoperability" and i think
that's busted.
Sponsored by: Norse Corp, Inc.
Some external tools just do a 'ls /dev/vmm' to figure out the bhyve virtual
machines on the host. These tools break if the devmem device nodes also
appear in /dev/vmm.
Requested by: grehan
flags are not specified... This bug was introduced in r275732...
This only affects IPsec ESP only policies w/ the aesni module loaded,
other subsystems specify one or both of the flags...
Reviewed by: gnn, delphij, eri
Add ARM ITS (Interrupt Translation Services) support required
to bring-up message signalled interrupts on some ARM64 platforms.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
pointer is NULL, as in that case there are no userland pages that
could potentially be wired. It is common for old to be NULL and
oldlenp to be non-NULL in calls to userland_sysctl(), as this is used
to probe for the length of a variable-length sysctl entry before
retrieving a value. Note that it is typical for such calls to be made
with an uninitialized value in *oldlenp, so sysctlmemlock was
essentially being acquired at random (depending on the uninitialized
value in *oldlenp being > PAGE_SIZE or not) for these calls prior to
this patch.
Differential Revision: https://reviews.freebsd.org/D2987
Reviewed by: mjg, kib
Approved by: jmallett (mentor)
MFC after: 1 month
Summary:
Both booke and AIM interrupt.c files contain nearly identical code. This merges
the two files, to reduce duplication.
Reviewers: #powerpc, marcel
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2991
bd_hdrcmplt. As if_loop does not use link-level headers, its behavior
when used by bpfwrite() should be the same regardless of the state of
bd_hdrcmplt. Without this change, libpcap (and other BPF users that
work like it) fail when writing to loopback interfaces.
Differential Revision: https://reviews.freebsd.org/D2989
Reviewed by: gnn, melifaro
Approved by: jmallett (mentor)
MFC after: 3 days
This obviates the need for a MNTK_SUSPENDABLE flag, since passthrough
filesystems like nullfs and unionfs no longer need to inherit this
information from their lower layer(s). This change also restores the
pre-r273336 behaviour of using the presence of a susp_clean VFS method to
request suspension support.
Reviewed by: kib, mjg
Differential Revision: https://reviews.freebsd.org/D2937
To avoid conflicts between target and initiator devices in CAM, make
CTL use target ID reported by HBA as its initiator_id in XPT_PATH_INQ.
That target ID is known to never be used for initiator role, so it won't
conflict. For Fibre Channel and FireWire HBAs this specific ID choice
is irrelevant since all target IDs there are virtual. Same time for SPI
HBAs it seems could be even requirement to use same target ID for both
initiator and target roles.
While there are some more things to polish in isp(4) driver, first tests
of using both roles same time on the same port appeared successfull:
# camcontrol devlist -v
scbus0 on isp0 bus 0:
<FREEBSD CTLDISK 0001> at scbus0 target 1 lun 0 (da20,pass21)
<> at scbus0 target 256 lun 0 (ctl0)
<> at scbus0 target -1 lun ffffffff (ctl1)
FreeBSD never had limitation on number of target IDs, and there is no
any other requirement to allocate them densely. Since slots of port
database already populated just sequentially, there is no much need
for another indirection to allocate sequentially too.
On Book-E, physical addresses are actually 36-bits, not 32-bits. This is
currently worked around by ignoring the top bits. However, in some cases, the
boot loader configures CCSR to something above the 32-bit mark. This is stage 1
in updating the pmap to handle 36-bit physaddr.
This will print out the Memory Subsystem Status Register on MPC745x (G4+ class),
and the Machine Check Status Register on Book-E class CPUs, to aid in debugging
machine checks. Other relevant registers, for other CPUs, can be added in the
future.
directory sys/contrib/libnv.
The goal of this operation is to NOT install header files which shouldn't
be used outside the nvlist library.
Approved by: pjd (mentor)
