sent SIGHUP and SIGCONT if any of the processes are stopped. Currently this
behavior is triggered for any type of process stop including ptrace() stops
and transient stops for single threading during exit() and execve().
Thus, if a debugger is attached to a process in a group when the leader
exits, the entire group can be HUPed. Instead, only send the signals if a
process in the group is stopped due to SIGSTOP.
PR: 201149
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3681
Problem description:
How do we currently perform layer 2 resolution and header imposition:
For IPv4 we have the following chain:
ip_output() -> (ether|atm|whatever)_output() -> arpresolve()
Lookup is done in proper place (link-layer output routine) and it is possible
to provide cached lle data.
For IPv6 situation is more complex:
ip6_output() -> nd6_output() -> nd6_output_ifp() -> (whatever)_output() ->
nd6_storelladdr()
We have ip6_ouput() which calls nd6_output() instead of link output routine.
nd6_output() does the following:
* checks if lle exists, creates it if needed (similar to arpresolve())
* performes lle state transitions (similar to arpresolve())
* calls nd6_output_ifp() which pushes packets to link output routine along
with running SeND/MAC hooks regardless of lle state
(e.g. works as run-hooks placeholder).
After that, iface output routine like ether_output() calls nd6_storelladdr()
which performs lle lookup once again.
As a result, we perform lookup twice for each outgoing packet for most types
of interfaces. We also need to maintain runtime-checked table of 'nd6-free'
interfaces (see nd6_need_cache()).
Fix this behavior by eliminating first ND lookup. To be more specific:
* make all nd6_output() consumers use nd6_output_ifp() instead
* rename nd6_output[_slow]() to nd6_resolve_[slow]()
* convert nd6_resolve() and nd6_resolve_slow() to arpresolve() semantics,
e.g. copy L2 address to buffer instead of pushing packet towards lower
layers
* Make all nd6_storelladdr() users use nd6_resolve()
* eliminate nd6_storelladdr()
The resulting callchain is the following:
ip6_output() -> nd6_output_ifp() -> (whatever)_output() -> nd6_resolve()
Error handling:
Currently sending packet to non-existing la results in ip6_<output|forward>
-> nd6_output() -> nd6_output _lle() which returns 0.
In new scenario packet is propagated to <ether|whatever>_output() ->
nd6_resolve() which will return EWOULDBLOCK, and that result
will be converted to 0.
(And EWOULDBLOCK is actually used by IB/TOE code).
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D1469
* prepare gateway before insertion
* use RTM_CHANGE instead of explicit find/change route
* Remove fib argument from ifa_switch_loopback_route added in r264887:
if old ifp fib differes from new one, that the caller
is doing something wrong
* Make ifa_*_loopback_route call single ifa_maintain_loopback_route().
that was recently added for Lenovo laptops.
This is a prime candidate for conversion into a table and also
checking other fields like "product".
Tested:
* ASUS UX31E
before proceeding. Otherwise, nothing prevents it from running after the
MAD agent struct has been been freed, and this results in a use-after-free
when the task's ta_pending count is incremented in the callout handler.
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
to sleep. The rmlock implementation enforces this by disabling
sleeping when a read lock is acquired. To simplify the implementation,
sleeping is disabled for most of the duration of rm_rlock. However,
it doesn't need to be disabled until the lock is acquired. If a
sleepable rm lock is contested, then rm_rlock may need to acquire the
backing sx lock. This tripped the overly-broad assertion. Fix by
relaxing the assertion around the call to sx_xlock().
Reported by: mjg
Reviewed by: kib, mjg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3324
In poll mode, check for and wake VBAD vnodes. (Vnodes that are VBAD at
registration will never be woken by the RECLAIM trigger.)
Add post-VOP_RECLAIM hook to trigger notes on vnode reclamation. (Vnodes that
were fine at registration but are vgoned while being monitored should signal
waiters.)
Reviewed by: kib
Approved by: markj (mentor)
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3675
it possible to "simulate" 4K media, to eg test alignment handling.
Reviewed by: mav@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3664
* Move isRouter calculation code to separate nd6_is_router() function.
* Make nd6_cache_lladdr() return void: its return value hasn't been used
since r53541 KAME import in 1999.
Sponsored by: Yandex LLC
There is an issue with interrupts at the moment, but it works with
polling mode set (hw.usb.xhci.use_polling=1).
Reviewed by: hselasky
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3665
Some more automated I2C controllers cannot explicitly create
START/STOP/etc. conditions on the bus.
Instead, the correct condition is set automatically according
to the pending transfer status.
This particular behavior can cause trouble if some I2C slave
requires sending address offset within the chip followed by
the actual data or command. In that case we cannot assume that
the driver will not STOP immediately after sending
offset.
To avoid that, do not split offset transfer from data transfer
for default transmission modes and do exactly that if requested
in command line (stop-start and repeated-start modes).
This more generic approach should cover special cases like
the one described.
Reviewed by: imp
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
chdone(). Previously, the retry could clear the CAM_DEV_QFRZN bit in the
CCB status, leaving the queue frozen.
Submitted by: Jeff Miller <Jeff.Miller@isilon.com>
Reviewed by: ken
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
Stale CTF tools are a frequent source of DTrace issues, and they compile
quickly enough that the increase in build time is negligible.
Reviewed by: emaste, imp
Differential Revision: https://reviews.freebsd.org/D3670
This allows for arbitrary channel info to be placed in the input call rather
than the totally gross hack of overriding ic_curchan.
Without this I'm sure ic_curchan setting was racing with the scan code
setting the channel itself..
On receipt of a redirect message, install an interface route for the
redirected destination. On removal of the corresponding Neighbor Cache
entry, remove the interface route.
This requires changes in rtredirect_fib() to cope with an AF_LINK
address for the gateway and with the absence of RTF_GATEWAY.
This fixes the "Redirected On-Link" test cases in the Tahi IPv6 Ready Logo
Phase 2 test suite.
Unrelated to the above, fix a recursion on the radix node head lock
triggered by the Tahi Redirected to Alternate Router test cases.
When I first wrote this patch in October 2012, all Section 2
(Neighbor Discovery) test cases passed on 10-CURRENT, 9-STABLE,
and 8-STABLE. cem@ recently rebased the 10.x patch onto head and reported
that it passes Tahi. (Thanks!)
These other test cases also passed in 2012:
* the RTF_MODIFIED case, with IPv4 and IPv6 (using a
RTF_HOST|RTF_GATEWAY route for the destination)
* the redirected-to-self case, with IPv4 and IPv6
* a valid IPv4 redirect
All testing in 2012 was done with WITNESS and INVARIANTS.
Tested by: EMC / Isilon Storage Division via Conrad Meyer (cem) in 2015,
Mark Kelley <mark_kelley@dell.com> in 2012,
TC Telkamp <terence_telkamp@dell.com> in 2012
PR: 152791
Reviewed by: melifaro (current rev), bz (earlier rev)
Approved by: kib (mentor)
MFC after: 1 month
Relnotes: yes
Sponsored by: Dell Inc.
Differential Revision: https://reviews.freebsd.org/D3602
