intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
The ci20 port (by kan@) is going to reuse almost all of the intrng code
since the SoC in question looks suspiciously like someone took an ARM
SoC design and replaced the ARM core with a MIPS core.
* migrate out the code;
* rename ARM_ -> INTR_;
* rename arm_ -> intr_;
* move the interrupt flush routine from intr.c / intrng.c into
arm/machdep_intr.c - removing the code duplication and removing
the ARM specific bits from here.
Thanks to the Star Wars: The Force Awakens premiere line for allowing
me a couple hours of quiet time to finish the universe builds.
Tested:
* make universe
TODO:
* The structure definitions in subr_intr.c still includes machine/intr.h
which requires one duplicates all of the intrng definitions in
the platform code (which kan has done, and I think we don't have to.)
Instead I should break out the generic things (function declarations,
common intr structures, etc) into a separate header.
* Kan has requested I make the PIC based IPI stuff optional.
Use proper size of exynos_ehci_softc, not the generic one.
Reviewed by: andrew
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4189
the name the function will have when the new ARM_INTRNG code is integrated,
and doing this rename first will make it easier to toggle the new interrupt
handling code on/off with a config option for debugging.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
initial thread stack is not adjusted by the tunable, the stack is
allocated too early to get access to the kernel environment. See
TD0_KSTACK_PAGES for the thread0 stack sizing on i386.
The tunable was tested on x86 only. From the visual inspection, it
seems that it might work on arm and powerpc. The arm
USPACE_SVC_STACK_TOP and powerpc USPACE macros seems to be already
incorrect for the threads with non-default kstack size. I only
changed the macros to use variable instead of constant, since I cannot
test.
On arm64, mips and sparc64, some static data structures are sized by
KSTACK_PAGES, so the tunable is disabled.
Sponsored by: The FreeBSD Foundation
MFC after: 2 week
If KSTACK_PAGES was changed to anything alse than the default,
the value from param.h was taken instead in some places and
the value from KENRCONF in some others. This resulted in
inconsistency which caused corruption in SMP envorinment.
Ensure all places where KSTACK_PAGES are used the opt_kstack_pages.h
is included.
The file opt_kstack_pages.h could not be included in param.h
because was breaking the toolchain compilation.
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3094
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
(4 in operation), 4GB ram (3.5 usable) ARM machine.
Support covers device drivers for:
- Serial Peripheral Interface (SPI)
- Chrome Embedded Controller (EC) - SPI-based version
- XHCI and USB 3.0 dual-role device PHY
Also:
- Add support for Exynos5420 in Pad module
- Move power-related functions to separate driver --
Power Management Unit (PMU)
- Enable XHCI for Chromebook1
Special thanks to grehan@ for hardware, and to
hselasky@ for r269139.
