o PC98 uses 32-bit block numbers. Limit the scheme to 2^32-1
blocks when the media is larger. The 32-bit block numbers
are implicit (16-bit cylinder * 8-bit head * 8-bit sector).
o EBR uses 32-bit block numbers. Limit the scheme to 2^32-1
blocks when the media is larger.
o Calculate the number of entries based on the rounded media
size, rather than the raw media size.
in directory vnodes. Allow namecache dotdot entry to be created pointing
from child vnode to parent vnode if no existing links in opposite
direction exist. Use direct link from parent to child for dotdot lookups
otherwise.
This restores more efficient dotdot caching in NFS filesystems which
was lost when vnodes stoppped being type stable.
Reviewed by: kib
It's quite strange that nobody reported this issue before. It turns out
functions like ttyname(), ptsname() and fdevname() don't work in
compat32. This means it't not even possible to run applications like
script(1) inside a 32-bit FreeBSD jail.
Fix this by converting 32-bit fiodgname_arg structures to their 64-bit
equivalent.
Reported by: kris
Tested by: kris
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
provider namespace. These are inserted dynamically into the
VOP_..._AP() functions created from vnode_if.src. Each VOP has
entry and return probes, as arg0 the primary vnode, arg1 the
vnode operation argument structure pointer, providing access to
IN and OUT arguments, and for return probes, arg2 the return
value.
MFC after: 1 month
Sponsored by: Google, Inc.
src/sys and not the entire src/ tree.
An earlier solution by peter had been comitted in r183528 and backed out
in r183566 due to problems with newvers.sh also called from other places
during world build. With the extra test this survived a make universe.
The work have been under testing and fixing since then, and it is mature enough
to be put into HEAD for further testing.
A lot have changed in this time, and here are the most important:
- Gvinum now uses one single workerthread instead of one thread for each
volume and each plex. The reason for this is that the previous scheme was
very complex, and was the cause of many of the bugs discovered in gvinum.
Instead, gvinum now uses one worker thread with an event queue, quite
similar to what used in gmirror.
- The rebuild/grow/initialize/parity check routines no longer runs in
separate threads, but are run as regular I/O requests with special flags.
This made it easier to support mounted growing and parity rebuild.
- Support for growing striped and raid5-plexes, meaning that one can extend the
volumes for these plex types in addition to the concat type. Also works while
the volume is mounted.
- Implementation of many of the missing commands from the old vinum:
attach/detach, start (was partially implemented), stop (was partially
implemented), concat, mirror, stripe, raid5 (shortcuts for creating volumes
with one plex of these organizations).
- The parity check and rebuild no longer goes between userland/kernel, meaning
that the gvinum command will not stay and wait forever for the rebuild to
finish. You can instead watch the status with the list command.
- Many problems with gvinum have been reported since 5.x, and some has been hard
to fix due to the complicated architecture. Hopefully, it should be more
stable and better handle edge cases that previously made gvinum crash.
- Failed drives no longer disappears entirely, but now leave behind a dummy
drive that makes sure the original state is not forgotten in case the system
is rebooted between drive failures/swaps.
- Update manpage to reflect new commands and extend it with some examples.
Sponsored by: Google Summer of Code 2007
Mentored by: le
Tested by: Rick C. Petty <rick-freebsd2008 -at- kiwi-computer.com>
It seems that some revision of controller hang while accessing
the VPD. Because VPD access routine are unused, nuke it.
o Let TWSI reload EEPROM if VPD capability is detected. Reloading
EEPROM will also set ethernet address so age(4) now reads AGE_PAR0
and AGE_PAR1 register to get ethernet address. This removes a lot
of hack and enhance readability a lot.
o Double PHY reset timeout as it takes more time to take PHY out of
power-saving state.
o Explicitly check power-saving state by checking undocumented PHY
registers. If link is not up, poke undocumented registers to take
PHY out of power-saving state. This is the same way what Linux
does. On resume, make sure to wake up PHY.
o Don't rely on auto-clearing feature of master reset bit, just wait
1ms and check idle status of MAC.
o Add PCI device revision information in bootverbose mode.
This should fix occasional controller hang in device attach phase.
Reported by: barbara < barbara.xxx1975 at libero DOT it >
Tested by: barbara < barbara.xxx1975 at libero DOT it >
This does not include the new hash routines since they will cause problems
when reading old hash files.
Since mpool(3) has been changed, provide a compatibility shim for older
binaries.
Obtained from: OpenBSD
open(). The previous logic only initializes the database when O_CREAT is
set, but as long as we can open and write the database, and the database
is empty, we should initialize it anyway.
Obtained from: OpenBSD
an invariant (actually, an ugly hack) to fail, and all Hell would break
loose.
When deleting a big key, the offset of an empty page should be bsize, not
bsize-1; otherwise an insertion into the empty page will cause the new key to
be elongated by 1 byte.
Make the packing more dense in a couple of cases.
- fix NULL dereference exposed on big bsize values;
Obtained from: NetBSD via OpenBSD
up) rather than amount + 1 / 2, which is the same as amount, or 2x too
many words which leads to data corruption.
# This fixes the sbdrop panics I was seeing with the Toshiba LANCT00A.
