Suggested by: nate
- get rid of "magick" values in code and make sysctl's reflecting reality
on processor versions which have one or another frequency "forbidden"
due to errata.
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after: 2 weeks
rev.1.1040. It is a miscellaneous isa+pci driver, but came back
described as a pci-only driver and placed in an i4b pci subsection
after its migration to /sys/conf/NOTES. Put it back where it used to
be, fully unsorted in the `Miscellaneous hardware' section. Reduced
nearby disorder in this section by moving configuration of the digi
driver to where it was for the old digiboard drivers, so that the
order at least matches the order in the table of contents.
- references to removed math emulators for NPX_DEBUG
- header for the null set of mandatory devices
- reference to the removed (and bogus when it existed) sysctl
kern.timecounter.method.
FIxed some nearby disorder (descriptions of CPU_BLUELIGHTNING_3X,
CPU_DIRECT_MAPPED_CACHE, CPU_DISABLE_CMPXCHG, CPU_DISABLE_SSE,
CPU_ELAN_XTAL and CPU_SOEKRIS, and options for all of these except
CPU_DIRECT_MAPPED_CACHE).
CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
TCC allows to restrict power consumption by using machdep.cpuperf*
sysctls. This operates independently of SpeedStep and is useful on
systems where other mechanisms such as apm(4) or acpi(4) don't work.
Given the fact that many, even modern, notebooks don't work properly
with Intel ACPI, this is indeed very useful option for notebook owners.
Obtained from: OpenBSD
MFC after: 2 weeks
lots of old interfaces, and digi now supports all cards that dgb
supported. The author of the driver says that this is no longer
necessary.
Approved by: babkin@
or whose drivers haven't even compiled for years.
The loran hardware was very unique, and only a few copies of it ever
existed. It used the old COMPAT_ISA_DRIVER and when the author was
contacted, he indicated that he had no intention of ever updating this
driver and it was no longer relevant to the FreeBSD world and can be
removed without impact to anybody.
Approved by: phk
Update notes to reflect that cx is no longer a counted device
Update options for new cx option
# commented out ELAN_PPS and ELAN_XTAL since they produced errors
Submitted by: rik@cronyx.ru
Approved by: re@ <scottl>
should only be used if they are enabled in the BIOS. Now that we support
enumerating CPUs using the ACPI MADT, any HTT machine using ACPI should
respect the BIOS setting. For HTT machines with ACPI disabled in the
kernel, the MPTABLE_FORCE_HTT kernel option can be used to try to probe HTT
CPUs like have done in the past for the MP Table case. This option should
only be enabled if HTT is enabled in the BIOS.
- Compile 'device acpi' into GENERIC by default as well. Note that
the beastie loader menu item to disable ACPI still works if ACPI is
compiled into the kernel.
Requested by: jhb
Initialize the real mode stack. This is needed at least for the return
address from the lcall.
Requested by: takawata
Fix style bugs in acpi_wakecode.S
Requested by: bde
Remove the kernel option now that we have the tunable.
enable strict checks of the AML. Our default behavior will be to relax
checks to work on as many platforms as possible. Also clean up and document
other ACPI options while I'm here.
of "dumb" PCI-based serial/parallel boards get a hint how to enable
them.
I wasn't sure about the ia64, pc98, powerpc, and sparc64 archs whether
they'd support puc(4) or not.
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
