"Terminus BSD Console" is a derivative of Terminus that is provided
by Mr. Dimitar Zhekov under the 2-clause BSD license for use by the FreeBSD vt(4) console.
Reviewed by: jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
- Properly align temporary buffer to 32-bit.
- Add an extra parenthesis to make expression clear.
- Range check the association ID received from hardware.
MFC after: 1 week
A similar fix should be applied to vmxnet, ixgbe, igb, i40e.
(some of them previously reported by Michael Tuexen)
Drivers using if_transmit are correct, and so are most of the
other drivers that reassing if_transmit.
Among other things, this bug causes panics when using netmap emulation
on top of generic drivers.
Approved by: bryanv
MFC after: 3 days
Core i7 and Westmere processors, the uncore PMC subsystem is
completely different from the uncore PMC on smaller versions of CPUs.
Disable existing uncore hwpmc code for EX, otherwise non-existing MSRs
are accessed.
The cores PMCs seems to be identical for non-EX and EX, according to
the SDM.
Reviewed by: davide, fabient
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
- The R92S_TCR register is an 8-bit register. Don't access it like a
16-bit register.
- Disable parsing the delete station event, due to many false events.
- Ensure that there is only one transfer queue for each endpoint, so
that packets transmitted don't get out of order.
MFC after: 1 week
- Reformat the entire man page
- Create a proper synopsis section
- Use itemized-lists to describe each flag, rather than paragraphs
- Cross-reference common flags to a 'general flags' sub-section with short
inline description of the flag
- Label 'general flags' sub-section
- Apply additional fixes suggested by wblock, brueffer, and bdrewery
- Update .Dd that got undone previously
- Change the order of the .Op Fl to be alphabetical
- Add the -i | -I interface flags to the description of 'interface
display mode'
- Fix missing parameters in man page
- Fix missing parameters in usage()
- Sync man page and usage()
MFC Note: stable/9 and stable/10 do not have -R, will need to be removed
when merged
CR: D58
Reviewed by: brueffer, bcr
Approved by: wblock (mentor)
MFC after: 7 days
Sponsored by: ScaleEngine Inc.
Walking a linked list of all glyphs to look for a duplicate is very slow
for large fonts (e.g., for CJK character sets). In my test the runtime
for a sample 40000 character font went from just over 80 seconds on
average to just over 2 seconds.
Sponsored by: The FreeBSD Foundation
The description of WITH/WITHOUT tweaks should only document the non-default
option. TESTS still defaults to no, so the option to be documented is
WITH_TESTS.
If you had a UFS2 FS that didn't have it's super block at SBLOCK_UFS2,
you'll end up corrupting your FS as the superblock is updated and written
to a different location...
makefs used to put the superblock at SBLOCK_UFS1 for UFS 2 FS's causing
this issue...
Reviewed by: silience from mckusick
MFC after: 1 week
selection. gethrtime() in our port updated with HZ rate, so unusable for
this specific purpose, completely draining benefit of multiple taskqueues.
MFC after: 2 weeks
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
o Always init locks and cv ASAP.
o Initialize driver-independent parts even if driver probing fail.
o Allow to call vt_upgrade anytime, for later loaded drivers.
o New window flag VWF_READY, to track if window already initialized.
Other updates:
o Pass vd as a cookie for kbd_allocate.
o Do not blank window on driver replacement.
Tested by: hselasky (RPi), emaste(VGA, EFIFB, KMS), me
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
o NR_REG_SW_NIC -> NR_REG_SW
o NR_RING_NIC_SW -> NR_REG_NIC_SW
o NETMAP_NO_TX_SYNC -> NETMAP_NO_TX_POLL
o NETMAP_DO_RX_SYNC -> NETMAP_DO_RX_POLL
I hope dear luigi has not left those as an excercise to careful
reader, in which case I apologize in advance for ruining his play.
MFC after: 1 week
Make it really work for native FreeBSD programs. Before this it was broken
for years due to different number of pointer dereferences in Linux and
FreeBSD IOCTL paths, permanently returning errors to FreeBSD programs.
This change breaks the driver FreeBSD IOCTL ABI, making it more strict,
but since it was not working any way -- who bother.
Add shims for 32-bit programs on 64-bit host, translating the argument
of the SG_IO IOCTL for both FreeBSD and Linux ABIs.
With this change I was able to run 32-bit Linux sg3_utils tools and simple
32 and 64-bit FreeBSD test tools on both 32 and 64-bit FreeBSD systems.
MFC after: 1 month
The directory hierarchy is created by an mtree file (BSD.usr.dist,
in the case of calendar(1)). An explicit "mkdir -p" in a program's
Makefile is redundant, and can mask a missing mtree entry.
