* change all splnet's to splimp's
*
* Revision 2.13 1993/11/22 10:53:52 davidg
* patch to add support for SMC8216 (Elite-Ultra) boards
* from Glen H. Lowe
*
* Revision 2.12 1993/11/07 18:04:13 davidg
* fix from Garrett Wollman:
* add a return(0) at the end of ed_probe so that if the various device
* specific probes fail that we just don't fall of the end of the function.
* Novell probe changed to be invasive because of too many complaints
* about some clone boards not being reset properly and thus not
* found on a warmboot. Yuck.
*
* Revision 2.10 1993/10/23 04:07:12 davidg
* increment output errors if the device times out (done via watchdog)
*
* Revision 2.9 1993/10/23 04:01:45 davidg
* increment input error counter if a packet with a bad length is
* detected.
* increase maximum time to wait for transmit DMA to complete to 120us.
* call ed_reset() if the time limit is reached instead of trying
* to abort the remote DMA.
*
* Revision 2.7 1993/10/15 10:49:10 davidg
* minor change to way the mbuf pointer temp variable is assigned in
* ed_start (slightly improves code readability)
*
* Revision 2.6 93/10/02 01:12:20 davidg
* use ETHER_ADDR_LEN in NE probe rather than '6'.
* patch from vak@zebub.msk.su (Serge V.Vakulenko) to work around
* a hardware bug in cheap WD clone boards where the PROM checksum
* byte is always zero
* Added software NIC reset in NE probe to work around a problem
* with some NE boards where the 8390 doesn't reset properly on
* power-up. Remove initialization of IMR/ISR in the NE probe
* because this is inherent in the reset.
* added no multi-buffer override for 3c503
*
* Revision 2.1 93/09/29 12:32:12 davidg
* changed multi-buffer count for 16bit 3c503's from 5 to 2 after
* noticing that the transmitter becomes idle because of so many
* packets to load.
*
* Revision 2.0 93/09/29 00:00:19 davidg
* many changes, rewrites, additions, etc. Now supports the
* NE1000, NE2000, WD8003, WD8013, 3C503, 16bit 3C503, and
* a variety of similar clones. 16bit 3c503 now does multi
* transmit buffers. Nearly every part of the driver has
* changed in some way since rev 1.30.
1) fixed 3c503 lock-up if the thinwire cable was disconnected at boot time
2) 8013EBT boards now work (quite well!) in 16bit/16k mode
3) ED_NO_DOUBLE_BUFFERING flag now works
4) slightly higer performance (about 3%) with 16bit WD/SMC boards
5) support for WD8013WC (10BaseT) boards
Additionally, the probe code has been reorganized to be much cleaner. This
revision of the driver is 1.25. The release notes have been updated as well.
profiling, and various protection checks that cause security holes
and system crashes.
* Changed min/max/bcmp/ffs/strlen to be static inline functions
- included from cpufunc.h in via systm.h. This change
improves performance in many parts of the kernel - up to 5% in the
networking layer alone. Note that this requires systm.h to be included
in any file that uses these functions otherwise it won't be able to
find them during the load.
* Fixed incorrect call to splx() in if_is.c
* Fixed bogus variable assignment to splx() in if_ed.c
* them in cpufunc.h. Modified wait loop in reset to look a little better.
* Added read for talley counters to prevent an infinite loop on old
* 8003E's if they (the counters) overflow.
asic register even if the board isn't a 3c503. This caused old 8003E's not
to work because they ignore IO address bits >10bits and the 3c503 asic is
located at +0x400....the offset was ignored by the 8003E and so the
value was written to one of the NIC registers. The bug was discovered by
Wolfgang Solfrank.
8bit or 16bit operation, and a flag to disable transmitter double buffering.
See the updated "ed.relnotes" file for information about how to set
the flags.
This should be considered the first "production" release. It still
needs a manual page, though.
