Although I _should_ handle the other errors in various ways (specifically
errors like FILT), treating them as having transmitted successfully
is completely wrong. Here, they'd be counted as successful and the BAW
would be advanced.. but the RX side wouldn't have received them.
The specific errors I've been seeing here are HAL_TXERR_FILT.
This patch does fix the issue - I've tested it using -i 0.001 pings
(enough to start aggregation) and now the behaviour is correct:
* The RX side never sees a "moved window" error, and
* The TX side sends BARs as needed, with the RX side correctly handling
them.
PR: kern/167902
compatible with the sched provider implemented by Solaris and its open-
source derivatives. Full documentation of the sched provider can be found
on Oracle's DTrace wiki pages.
Note that for compatibility with scripts originally written for Solaris,
serveral probes are defined that will never fire. These probes are defined
to fire when Solaris-specific features perform certain actions. As these
features are not present in FreeBSD, the probes can never fire.
Also, I have added a two probes that are not defined in Solaris, lend-pri
and load-change. These probes have been added to make it possible to
collect schedgraph data with DTrace.
Finally, a few probes are defined in Solaris to take a cpuinfo_t *
argument. As it was not immediately clear to me how to translate that to
FreeBSD, currently those probes are passed NULL in place of a cpuinfo_t *.
Sponsored by: Sandvine Incorporated
MFC after: 2 weeks
compiler frame size used there so this whole thing is V8/V9-agnostic.
- Use 32-bit function alignment as GCC does when using UltraSPARC I or
higher optimizations.
- Don't waste delay slots when possible.
Unfortunately, this still doesn't make libcompiler_rt a viable replacement
for libgcc on sparc64 though as once installed instead, buildworld times
increase by nearly 60% (which isn't related to these assembler functions).
used, when the code should actually protect the tested
variable with a mutex. Since the tsleep()s had a 10sec
timeout, the race would have only delayed the allocation
of a new clientid for a client. The sleeps will also
rarely occur, since having a callback in progress when
a client acquires a new clientid, is unlikely.
in practice, since having a callback in progress when
a fresh clientid is being acquired by a client is unlikely.
MFC after: 1 month
depending upon the bootloader initialising it.
The aim is to eventually support a full switch set and reinitialisation
rather than relying on a consistent bootloader setup.
Remove the port flood config from arswitch.c, it's not yet used and
it's totally incorrect.
Whilst I'm here, also add in a comment describing why the full switch
reset is disabled.
Obtained from: Linux (OpenWRT) - Values
which carries fictitous managed pages. In particular, the consumers of
the new object type can remove all mappings of the device page with
pmap_remove_all().
The range of physical addresses used for fake page allocation shall be
registered with vm_phys_fictitious_reg_range() interface to allow the
PHYS_TO_VM_PAGE() to work in pmap.
Most likely, only i386 and amd64 pmaps can handle fictitious managed
pages right now.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 1 month
for allocation of fictitious pages, for which PHYS_TO_VM_PAGE()
returns proper fictitious vm_page_t. The range should be de-registered
after consumer stopped using it.
De-inline the PHYS_TO_VM_PAGE() since it now carries code to iterate
over registered ranges.
A hash container might be developed instead of range registration
interface, and fake pages could be put automatically into the hash,
were PHYS_TO_VM_PAGE() could look them up later. This should be
considered before the MFC of the commit is done.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 1 month
