In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
The controller is commonly found on DM&P Vortex86 x86 SoC. The
driver supports all hardware features except flow control. The
flow control was intentionally disabled due to silicon bug.
DM&P Electronics, Inc. provided all necessary information including
sample board to write driver and answered many questions I had.
Many thanks for their support of FreeBSD.
H/W donated by: DM&P Electronics, Inc.
Bring in a driver for the LSI Logic MPT2 6Gb SAS controllers.
This driver supports basic I/O, and works with SAS and SATA drives and
expanders.
Basic error recovery works (i.e. timeouts and aborts) as well.
Integrated RAID isn't supported yet, and there are some known bugs.
So this isn't ready for production use, but is certainly ready for
testing and additional development. For the moment, new commits to this
driver should go into the FreeBSD Perforce repository first
(//depot/projects/mps/...) and then get merged into -current once
they've been vetted.
This has only been added to the amd64 GENERIC, since that is the only
architecture I have tested this driver with.
Submitted by: scottl
Discussed with: imp, gibbs, will
Sponsored by: Yahoo, Spectra Logic Corporation
Use MACHINE_CPUARCH in preference to MACHINE_ARCH. The former is the
source code location of the machine, the latter the binary output. In
general, we want to use MACHINE_CPUARCH instead of MACHINE_ARCH unless
we're tesitng for a specific target. The isn't even moot for
i386/amd64 where there's momemntum towards a MACHINE_CPUARCH == x86,
although a specific cleanup for that likely would be needed...
Add kernel side support for Secure Neighbor Discovery (SeND), RFC 3971.
The implementation consists of a kernel module that gets packets from
the nd6 code, sends them to user space on a dedicated socket and reinjects
them back for further processing.
Hooks are used from nd6 code paths to divert relevant packets to the
send implementation for processing in user space. The hooks are only
triggered if the send module is loaded. In case no user space
application is connected to the send socket, processing continues
normaly as if the module would not be loaded. Unloading the module
is not possible at this time due to missing nd6 locking.
The native SeND socket is similar to a raw IPv6 socket but with its own,
internal pseudo-protocol.
Approved by: bz (mentor)
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.
Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.
This commit requires IP6PROTOSPACER, introduced in r211115.
Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks
module that can be used by both the regular and experimental nfs
clients. This fixes the problem reported by jh@ where /dev/nfslock
would be registered twice when both nfs clients were used.
I also defined the size of the lm_fh field to be the correct value,
as it should be the maximum size of an NFSv3 file handle.
Reviewed by: jh
MFC after: 2 weeks
The aeskeys_{amd64,i386}.S content was mostly obtained from OpenBSD,
no objections to the license from core.
Hardware provided by: Sentex Communications
Tested by: fabient, pho (previous versions)
MFC after: 1 month
FreeBSD. SIFTR logs a range of statistics on active TCP connections to a log
file, providing the ability to make highly granular measurements of TCP
connection state. The tool is aimed at system administrators, developers and
researchers alike. Please take it for a spin and test it out - the man page
should have all the information required to get you going.
Many thanks go to the Cisco University Research Program Fund at Community
Foundation Silicon Valley and the FreeBSD Foundation. Their support of our work
at the Centre for Advanced Internet Architectures, Swinburne University of
Technology is greatly appreciated.
Sponsored by: Cisco URP, FreeBSD Foundation
Reviewed by: dwmalone, gnn, rpaulo
Tested by: Many on freebsd-current@ and elsewhere over the years
MFC after: 1 month
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
useful it will be, but we really need to be keying off something other
than MACHINE for this anyway since on arm and mips we have lots of
these running around (one for each SoC family)...
Rather than remove it for all architectures (which was a botch in
r205845), remove it only for arm and mips until that can be sorted out.
Pointy Hat: imp
Submitted by: Navdeep Parhar
MFC after: 7 days
into):
o Don't build vpo and syscons on mips or arm either
o Add a section for mips and arm breakages, and document why.
This is easier than opting in on all the other architectures:
# no BUS_SPACE_UNSPECIFIED: bce, bwi, bwn, mfi, mpt, siba_bwn
# No barrier instruction support (specific to this driver): sym
# no uart_cpu_$MACHINE_ARCH: uart
(mips has, by inspection, the same issues as arm, so ditto for it)
MFC after: 7 days
o Switch to ITANIUM2 has the cpu. This has absolutely no effect
on the code, but makes for a better example.
o Drop COMPAT_FREEBSD6. We're tier 2, so you're supposed to run
8-stable or newer.
o Add PREEMPTION. It works now.
o Remove HWPMC_HOOKS. We don't have support for hwpmc yet.
o Add a bunch of new devices: atapist, hptiop, amr, ips, twa, igb,
ixgbe, ae, age, alc, ale, bce, bfe, et, jme, msk, nge, sk, ste,
stge, tx, vge, axe, rue, udav, fwip, and all USB serial.
o Remove "legacy" devices: le, vx, dc, pcn, rl, sis.
Make sure to the module list is a superset of what goes into GENERIC.
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
