(with other names) in the USB driver sources, but I felt that pcireg.h
should have a complete list - at least of classes and interfaces that we
know about and use.
or sched_lock are sufficient to test this flag.
XXX: vinum should really be using a kernel process via kthread_create()
instead of this hack. I'm not even sure PS_INMEM can be clear at this
point anyways.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
other initializations succeeded.
- Initialize the TX and RX rings in epic_attach() rather than in
epic_init() where we're not supposed to fail. Similarly, free
the TX and RX rings in epic_detach() rather than in epic_stop().
- Change epic_init() to be a void function now that it can't fail.
Also change its parameter to a void * so that we have a correct
prototype for if_init.
- Now that epic_init() has a correct prototype, don't cast the
function pointer when initializing if_init.
- Fix nearby style bugs.
- Don't initialize if_output, ether_ifattach() does this for us.
- Use pci_enable_busmaster() instead of using pci_read_config()
and pci_write_config() directly.
- Don't try to enable I/O, bus_alloc_resource() does this for us.
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
bytes_in_mbuf rather than MCLBYTES. Add the ethertnet header to the
front of the mbuf. Adjust bytes_in_mbuf inside the loop that reads
the packet out of the card.
codec during initialization. This code mirrors the reset code used on
the VIA82c686 and fixes a codec initialization failure (SoundMAX
AD1885) reported by Matthias Schuendehuette.
in dc_detach() instead of only calling it if the hardware is preset.
This is a workaround for page faults in softclock() after a `dc'
device was detached, caused by not disabling a timer before freeing
its memory. The bus_child_present() checks should probably be
re-added later, but only to avoid the hardware accesses and not the
other resource cleanups in dc_stop().
Approved by: njl
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
PCIM_CMD_MEMEN and PCIM_CMD_BUSMASTEREN, becaise some braindead
BIOSes (such as one found in my vprmatrix notebook) forget
to initialize it properly resulting in attachment failure.
the list of supported sleep state.
This should help people understand what following message means.
acpi0: AcpiGetSleepTypeData failed - AE_NOT_FOUND
MFC after: 3 days
- Remove a useless device_is_alive() check.
- Disable interrupts if bus_child_present() so that this
check is more useful.
This fixes the hangs I was seeing when unloading the fxp driver.
Suggestions from: hsu, njl
- Be sure to teardown the interrupt first so that "kldunload if_fxp"
doesn't panic the box. It's now deadlocking rather than crashing,
which isn't really better, but I'm unsure this is fxp(4)'s fault.
- Change a bus_dmamap_sync() call to also do a BUS_DMASYNC_PREREAD
now that we can pass several operations.
is required. NetBSD has one because it checks for the mac address
match as well wanting to give its own string in the description.
Since we do neither, we don't need a separate entry.
# I suspect that a few of the COREGA cards might fall into that category
# as well, but since I don't have access to any of them it is hard to know
# for sure.
enet_mcast fields, so remove them. Sort. Eliminate now duplicate
entries.
This reorg saves about 500 bytes in the binary. I've tested this only
with a couple of cards, so please let me know if I've broken anything.
1.182; christos
A cardflash NE2000 from Michael Francini
1.181; perry
support Corega PCCL-11 -- from Christopher SEKIYA in PR 20932
1.180; ichiro
add product TOSHIBA PA2673U CBIDE2 (IODATA OEM)
1.179; kanaoka
Add SMC 8041TX 10/100 Ether PC Card.
0 in a problem that is being discussed. That means that the test for
product != 0 may cause problems. Looking at pccarddevs (which i
should have done earlier) we see:
product BONDWELL B236 0x0000 Game Card Joystick
product CONTEC CNETPC 0x0000 Contec C-NET(PC)C
product IBM MICRODRIVE 0x0000 IBM Microdrive
product RAYTHEON WLAN 0x0000 WLAN Adapter
product SOCKET EA_ETHER 0x0000 Socket Communications EA
product TDK LAK_CD011WL 0x0000 TDK LAK-CD011WL
so use only the vendor field for the end sentinel.
- Don't bother setting OACTIVE when the descriptors are all full
or there's a vr_encap failure, it doesn't help anything.
- Correctly roll back on the descriptor list after a failure
so as not to corrupt the list.
- Add a missing VR_UNLOCK().
Without these changes, vr_encap failure (which is assured during
a low mbuf situation) would result in the card locking until
the watchdog could fire.
MFC after: 1 week
Boost sample rate to 1.25 MSPS since that allows us to use a 5Mhz
(/4) or 10Mhz (/8) external clock.
Make the interrupt both MPSAFE and FAST, at 610 interrupts a second,
and a max time to service of 5 msec, we brake for nobody.
Use kernel thread to accumulate into the 25 possible wave signals.
Use #ifdef _KERNEL to let .c file double as .h file defining the ioctls.
of the entries have a description, we'll use that to override the
description that the pccard layer generates for us.
This saves about 930 bytes in the module, so I feel it won't hurt the
crowded boot disks....
# other modules to follow
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
o Only complain about detached children that aren't pccard/cardbus.
o Don't NULL out the pccarddev and cbdev devices. detach just
disassociates the device and driver. It doesn't delete the child.
o on driver added, just probe_and_attach the children. If there's
any children attached, wakeup the device add/delete thread.
o wakeup the add/delete thread with the correct cv_signal() rather
than the bogus wakeup(sc). It used to be that we did a tsleep on
sc in this thread, but switched to the more reliable cv stuff a while
ago w/o changing this.
o Remove bogus checks when reallocating memory for the registers. They
weren't needed and turned out to be completely bogus.
This lets me load/unload pccard with a pccard in a slot and have the
child correctly detach/attach. This should help people that have wi
in their kernel, but that kldload cbb and pccard, for example.
we're using an atomic operation to clear the suspend flag
in fxp_start(). Since other architectures may need the
same thing, we want to do it all the time and not only
in the __alpha__ case. However, we don't want to use
atomic operations on 16-bit integers, because those may
not be available on any architecture. We're thus faking
a 32-bit atomic operation here. This patch also deals
with endianness here.
which deals with both endianness and alignment issues.
- Collect low-hanging fruits for endianness safety.
- Use 0xffffffff instead of -1 where appropriate.
endian safe.
- Change some u_int to u_int8_t which make more sense here since
we're really defining bytes. That produces the same code due to
how bitfields work.
- Add the definition of the vlan_drop_en bit (not used yet).
- Add some useful comments.
Obtained from: NetBSD
other allocations/initializations have been successful. I kinda
doubt it will fix the recent breakage that some people are seeing,
but this could have caused problems for sure.
actual address of buffer descriptor. This should fix the reported
calibration failures and subsequent speed problems with ich chipsets.
Minor calibration comment updates.
This patch is rather big because I had to significantly redesign
the driver to make the busdma conversion possible. Most notably,
hardware and software structures were carefully splitted to get
rid of all the structs overlapping evilness.
Special thanks to phk and Richard Puga <puga@mauibuilt.com> for
providing me with fxp(4) hardware to do this work.
Thanks to marcel for testing this on ia64, and to Fred Clift
<fclift@verio.net> for testing this on alpha.
Tested on: i386, ia64, alpha
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
is enabled when both the size of bus_addr_t > 4 and the card claims support.
Don't wake up the kthread to allocate more commands if we know that we've
already allocated the max number of commands.
function.
Also, use m_defrag where appropriate to defrag long mbuf chains
in the same fashion as was done in if_sis.c. Before this change,
if_dc would blow up and take down the interface if fed a really long
mbuf chain.
MFC after: 2 weeks
Clean up the DMA interface too much unneeded stuff crept in with
the busdma code back when.
Modify the ATA_IN* / ATA_OUT* macros so that resource and offset
are gotten from a table. That allows for new chipsets that doesn't
nessesarily have things ordered the good old way. This also removes
the need for the wierd PC98 resource functions.
Tested on: i386, PC98, Alpha, Sparc64
the adapter from becoming wedged when when the interface is
is brought up by ether_ioctl() (when you set an IP address for example.)
Confirmed this "fix" from NetBSD's i82586 backend. It seems hackish
to me but whatever.
- Sanitize dpt_alloc().
- Add helper functions for resource alloc/release.
- Add detach method.
- Relocate definition of devclass_t.
- Move some debugging output behind bootverbose.
- Implement an identify method for ISA devices
but don't use it right now.
- Add data structuress for doing 64-bit scatter/gather
- Move busdma tag creations around so that only the parent is
created in aac_pci.c.
- Retrieve the capabilities word from the firmware before setting
up command structures and tags. This allows the driver to decide
whether to do 64-bit commands, and if work-arounds are needed for
systems with >2GB of RAM.
- Only enable the SCSI passthrough if it's enabled in the capabilities
word in the firmware.
This should fix problems with the 2120S and 2200S cards in systems with more
than 2GB of RAM. Full 64-bit support is forthcoming.
MFC-After: 1 week
and be prepared to wait much longer for codec to become ready.
Credit to Hugo D. Valentim <hvalentim@gmx.net> for reporting the
problem, providing useful pointers, and repeated diff testing.
channel and disable DXS3. Several users have reported DXS3 as playing
at half speed on the 8233A revision of the chipset. This implicitly
means no SPDIF for VIA8233A users.
The former fakes a valid response to an inquiry command. (I am completely
blown away that there are devices which hang upon receiving inquiry). The
latter returns "invalid request" to any inquiry commands with EVPD set.
NO_INQUIRY implies NO_INQUIRY_EVPD but not vice versa. Both quirks have been
tested separately on my USB key although it didn't require either of them.
While I'm here, fix wildcarding so that any/all of vendor, product, revision
can be wildcarded.
Idea from: Linux
MFC after: 2 weeks
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
Otherwise sysbeep() makes an annoying clicking sound on some systems.
'kbdcontrol -b off' just sets the duration and pitch to zero, it doesn't
set the QUIET_BELL flag.
Tested by: SorAlx <soralx@cydem.zp.ua>
PR: misc/41772
MFC after: 1 week
