initialize a TSC timecounter until we know if it is broke or not.
XXX I think there is a bug in the i386 code here. init_TSC_tc() comes
after:
if (statclock_disable)
return;
ie: if you turn off the statclock interrupt, you dont get the TSC either.
for ddb input in some atkbd-based console drivers. ddb must not use any
normal locks but DELAY() normally calls getit() which needs clock_lock.
This also removes the need for recursion on clock_lock.
value on entry and exit. This isn't as easy as it sounds because when
we recursively trap or interrupt, we have to avoid duplicating the
swapgs instruction or we end up back with the userland %gs. I implemented
this by testing TF_CS to see if we're coming from supervisor mode
already, and check for returning to supervisor. To avoid a race with
interrupts in the brief period after beginning executing the handler and
before the swapgs, convert all trap gates to interrupt gates, and reenable
interrupts immediately after the swapgs. I am not happy with this.
There are other possible ways to do this that should be investigated.
(eg: storing the GS.base MSR value in the trapframe)
Add some sysarch functions to let the userland code get to this.
Approved by: re (blanket amd64/*)
a heavily stripped down FreeBSD/i386 (brutally stripped down actually) to
attempt to get a stable base to start from. There is a lot missing still.
Worth noting:
- The kernel runs at 1GB in order to cheat with the pmap code. pmap uses
a variation of the PAE code in order to avoid having to worry about 4
levels of page tables yet.
- It boots in 64 bit "long mode" with a tiny trampoline embedded in the
i386 loader. This simplifies locore.s greatly.
- There are still quite a few fragments of i386-specific code that have
not been translated yet, and some that I cheated and wrote dumb C
versions of (bcopy etc).
- It has both int 0x80 for syscalls (but using registers for argument
passing, as is native on the amd64 ABI), and the 'syscall' instruction
for syscalls. int 0x80 preserves all registers, 'syscall' does not.
- I have tried to minimize looking at the NetBSD code, except in a couple
of places (eg: to find which register they use to replace the trashed
%rcx register in the syscall instruction). As a result, there is not a
lot of similarity. I did look at NetBSD a few times while debugging to
get some ideas about what I might have done wrong in my first attempt.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
I was in two minds as to where to put them in the first case..
I should have listenned to the other mind.
Submitted by: parts by davidxu@
Reviewed by: jeff@ mini@
prevent the compiler from optimizing assignments into byte-copy
operations which might make access to the individual fields non-atomic.
Use the individual fields throughout, and don't bother locking them with
Giant: it is no longer needed.
Inspired by: tjr
statclock based on profhz when profiling is enabled MD, since most platforms
don't use this anyway. This removes the need for statclock_process, whose
only purpose was to subdivide profhz, and gets the profiling clock running
outside of sched_lock on platforms that implement suswintr.
Also changed the interface for starting and stopping the profiling clock to
do just that, instead of changing the rate of statclock, since they can now
be separate.
Reviewed by: jhb, tmm
Tested on: i386, sparc64
The correct range is [1...7] with Sunday=1, but we have been writing
[0...6] with Sunday=0.
The Soekris computers flagged the zero, zapped the date, so if you
rebooted your soekris on a sunday, it would come up with a wrong
date.
Bruce has a more extensive rework of this code, but we will stick with
the minimalist fix for now.
Spotted by: Soren Kristensen <soren@soekris.com>
Thanks to: Michael Sierchio <kudzu@tenebras.com>.
Confirmed by: bde
Approved by: re
Previously these were libc functions but were requested to
be made into system calls for atomicity and to coalesce what
might be two entrances into the kernel (signal mask setting
and floating point trap) into one.
A few style nits and comments from bde are also included.
Tested on alpha by: gallatin
2. Update a comment. We now restore much more than RTC updates and
interrupts.
3. Order change. Stop interrupts by writing to RTC_STATUSB,
restore rate bits for the interrupts by writing to RTC_STATUSA,
then enable interrupts again.
This seems to be done perfectly backwards in startrtclock().
Otherwise, the idea for this change was obtained from
startrtclock().
4. Don't stop the clock (RTCB_HALT). We only program some control bits
and don't want to stop the clock.
5. (Not really related.) Add caveats to the comment about timer_restore().
The update is non-atomic since locking is not done.
On locking:
6. rtcin() and writertc() are locked() adequately by splhigh() in RELENG_4,
but this locking is null in -current.
7. Doing things in the correct order in (3) combined with (6) is probably
enough locking for rtcrestore() in RELENG_4. In -current, the
writertc()'s race with rtcintr() unless the BIOS disables RTC interrupts.
Submitted by: bde (including commit message)
MFC after: 1 week
if compiling with I686_CPU as a target. CPU_DISABLE_SSE will prevent
this from happening and will guarantee the code is not compiled in.
I am still not happy with this, but gcc is now generating code that uses
these instructions if you set CPUTYPE to p3/p4 or athlon-4/mp/xp or higher.
- It actually works this time, honest!
- Fine grained TLB shootdowns for SMP on i386. IPI's are very expensive,
so try and optimize things where possible.
- Introduce ranged shootdowns that can be done as a single IPI.
- PG_G support for i386
- Specific-cpu targeted shootdowns. For example, there is no sense in
globally purging the TLB cache for where we are stealing a page from
the local unshared process on the local cpu. Use pm_active to track
this.
- Add some instrumentation for the tlb shootdown code.
- Rip out SMP code from <machine/cpufunc.h>
- Try and fix some very bogus PG_G and PG_PS interactions that were bad
enough to cause vm86 bios calls to break. vm86 depended on our existing
bugs and this was the cause of the VESA panics last time.
- Fix the silly one-line error that caused the 'panic: bad pte' last time.
- Fix a couple of other silly one-line errors that should have caused more
pain than they did.
Some more work is needed:
- pmap_{zero,copy}_page[_idle]. These can be done without IPI's if we
have a hook in cpu_switch.
- The IPI handlers need some cleanup. I have a bogus %ds load that can
be avoided.
- APTD handling is rather bogus and appears to be a large source of
global TLB IPI shootdowns for no really good reason.
I see speedups of between 1.5% and ~4% on buildworlds in a while 1 loop.
I expect to see a bigger difference when there is significant pageout
activity or the system otherwise has memory shortages.
I have backed out a few optimizations that I had been using over the last
few days in order to be a little more conservative. I'll revisit these
again over the next few days as the dust settles.
New option: DISABLE_PG_G - In case I missed something.
when machdep.tsc_freq returned a negative number on a 2.2GHz Xeon.
Submitted by: Brian Harrison <bharrison@ironport.com>
Reviewed by: phk
MFC after: 1 week
i386/ia64/alpha - catch up to sparc64/ppc:
- replace pmap_kernel() with refs to kernel_pmap
- change kernel_pmap pointer to (&kernel_pmap_store)
(this is a speedup since ld can set these at compile/link time)
all platforms (as suggested by jake):
- gc unused pmap_reference
- gc unused pmap_destroy
- gc unused struct pmap.pm_count
(we never used pm_count - we track address space sharing at the vmspace)
timecounter will be used starting at the next second, which is
good enough for sysctl purposes. If better adjustment is needed
the NTP PLL should be used.
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
and cpu_critical_exit() and moves associated critical prototypes into their
own header file, <arch>/<arch>/critical.h, which is only included by the
three MI source files that need it.
Backout and re-apply improperly comitted syntactical cleanups made to files
that were still under active development. Backout improperly comitted program
structure changes that moved localized declarations to the top of two
procedures. Partially re-apply one of the program structure changes to
move 'mask' into an intermediate block rather then in three separate
sub-blocks to make the code more readable. Re-integrate bug fixes that Jake
made to the sparc64 code.
Note: In general, developers should not gratuitously move declarations out
of sub-blocks. They are where they are for reasons of structure, grouping,
readability, compiler-localizability, and to avoid developer-introduced bugs
similar to several found in recent years in the VFS and VM code.
Reviewed by: jake
disablement assumptions in kern_fork.c by adding another API call,
cpu_critical_fork_exit(). Cleanup the td_savecrit field by moving it
from MI to MD. Temporarily move cpu_critical*() from <arch>/include/cpufunc.h
to <arch>/<arch>/critical.c (stage-2 will clean this up).
Implement interrupt deferral for i386 that allows interrupts to remain
enabled inside critical sections. This also fixes an IPI interlock bug,
and requires uses of icu_lock to be enclosed in a true interrupt disablement.
This is the stage-1 commit. Stage-2 will occur after stage-1 has stabilized,
and will move cpu_critical*() into its own header file(s) + other things.
This commit may break non-i386 architectures in trivial ways. This should
be temporary.
Reviewed by: core
Approved by: core
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
