sbuf_new_for_sysctl(9). This allows using an sbuf with a SYSCTL_OUT
drain for extremely large amounts of data where the caller knows that
appropriate references are held, and sleeping is not an issue.
Inspired by: rwatson
unfunctional. Wiring the user buffer has only been done explicitly
since r101422.
Mark the kern.disks sysctl as MPSAFE since it is and it seems to have
been mis-using the NOLOCK flag.
Partially break the KPI (but not the KBI) for the sysctl_req 'lock'
field since this member should be private and the "REQ_LOCKED" state
seems meaningless now.
the controller has a kind of embedded controller/memory and vendor
applies a large set of magic code via undocumented PHY registers in
device initialization stage. I guess it's a firmware image for the
embedded controller in RTL8105E since the code is too big compared
to other DSP fixups. However I have no idea what that magic code
does and what's purpose of the embedded controller. Fortunately
driver seems to still work without loading the firmware.
While I'm here change device description of RTL810xE controller.
H/W donated by: Realtek Semiconductor Corp.
exact model name is not clear yet. All previous RTL8201 10/100 PHYs
used 0x8201 in MII_PHYIDR2 which in turn makes model number 0x20
but this PHY used new model number 0x08.
capability. One of reason using interrupt taskqueue in re(4) was
to reduce number of TX/RX interrupts under load because re(4)
controllers have no good TX/RX interrupt moderation mechanism.
Basic TX interrupt moderation is done by hardware for most
controllers but RX interrupt moderation through undocumented
register showed poor RX performance so it was disabled in r215025.
Using taskqueue to handle RX interrupt greatly reduced number of
interrupts but re(4) consumed all available CPU cycles to run the
taskqueue under high TX/RX network load. This can happen even with
RTL810x fast ethernet controller and I believe this is not
acceptable for most systems.
To mitigate the issue, use one-shot timer register to moderate RX
interrupts. The timer register provides programmable one-shot timer
and can be used to suppress interrupt generation. The timer runs at
125MHZ on PCIe controllers so the minimum time allowed for the
timer is 8ns. Data sheet says the register is 32 bits but
experimentation shows only lower 13 bits are valid so maximum time
that can be programmed is 65.528us. This yields theoretical maximum
number of RX interrupts that could be generated per second is about
15260. Combined with TX completion interrupts re(4) shall generate
less than 20k interrupts. This number is still slightly high
compared to other intelligent ethernet controllers but system is
very responsive even under high network load.
Introduce sysctl variable dev.re.%d.int_rx_mod that controls amount
of time to delay RX interrupt processing in units of us. Value 0
completely disables RX interrupt moderation. To provide old
behavior for controllers that have MSI/MSI-X capability, introduce
a new tunable hw.re.intr_filter. If the tunable is set to non-zero
value, driver will use interrupt taskqueue. The default value of
the tunable is 0. This tunable has no effect on controllers that
has no MSI/MSI-X capability or if MSI/MSI-X is explicitly disabled
by administrator.
While I'm here cleanup interrupt setup/teardown since re(4) uses
single MSI/MSI-X message at this moment.
with the latest socket API ID. Especially it can be disabled.
Full compliance needs changing the structure used in the
socket option. Since this breaks the API, it will be a
seperate commit which will not be MFCed to stable/8.
MFC after: 3 months.
ath9k does a few different things here during config - if it's an early
AR5416 with two chains, it enables all three chains for calibration and
then restores the chainmask to the original values after initial
calibration has completed.
The reason behind this commit is to begin breaking out the chainmask
configuration for this specific reason; follow-up commits will add
the chainmask restore in the ar5416Reset() routine.
recent PCIe controllers(RTL8102E or later and RTL8168/8111C or
later) supports either 2 or 4 MSI-X messages. Unfortunately vendor
did not publicly release RSS related information yet. However
switching to MSI-X is one-step forward to support RSS.
architectures that support this .note. In particular, do not unneccessary
emit the notes on ia64 and sparc64, which ABI require non-executable stacks.
Tested by: marcel
* There is no plan for an alternative to the command "set".
* Attempting to unset a readonly variable has not raised an error for quite
a while, so the order of unsetting a variable and a function with the same
name does not matter.
MFC after: 1 week
RTL8111C generated corrupted frames where TCP option header was
broken. All other sample controllers I have did not show such
problem so it could be RTL8111C specific issue. Because there are
too many variants it's hard to tell how many controllers have such
issue. Just disable TSO by default but have user override it.
before checking the validity of the next buffer pointer. Otherwise, the
buffer might be reclaimed after the check, causing iteration to run into
wrong buffer.
Reported and tested by: pho
MFC after: 1 week
Properly document what `make targets` is supposed to list to avoid
further confusion given the place the target sits. Should have happened
with r217125.
Requested by: imp [1]
Reviewed by: rwatson
* Re-do the structure size/component math to make sure the struct matches
the expected size
* Just to be clear that we care about bitmask ordering, revert my previous
change and instead define that macro if we're on big-endian.
