compiler frame size used there so this whole thing is V8/V9-agnostic.
- Use 32-bit function alignment as GCC does when using UltraSPARC I or
higher optimizations.
- Don't waste delay slots when possible.
Unfortunately, this still doesn't make libcompiler_rt a viable replacement
for libgcc on sparc64 though as once installed instead, buildworld times
increase by nearly 60% (which isn't related to these assembler functions).
used, when the code should actually protect the tested
variable with a mutex. Since the tsleep()s had a 10sec
timeout, the race would have only delayed the allocation
of a new clientid for a client. The sleeps will also
rarely occur, since having a callback in progress when
a client acquires a new clientid, is unlikely.
in practice, since having a callback in progress when
a fresh clientid is being acquired by a client is unlikely.
MFC after: 1 month
depending upon the bootloader initialising it.
The aim is to eventually support a full switch set and reinitialisation
rather than relying on a consistent bootloader setup.
Remove the port flood config from arswitch.c, it's not yet used and
it's totally incorrect.
Whilst I'm here, also add in a comment describing why the full switch
reset is disabled.
Obtained from: Linux (OpenWRT) - Values
which carries fictitous managed pages. In particular, the consumers of
the new object type can remove all mappings of the device page with
pmap_remove_all().
The range of physical addresses used for fake page allocation shall be
registered with vm_phys_fictitious_reg_range() interface to allow the
PHYS_TO_VM_PAGE() to work in pmap.
Most likely, only i386 and amd64 pmaps can handle fictitious managed
pages right now.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 1 month
for allocation of fictitious pages, for which PHYS_TO_VM_PAGE()
returns proper fictitious vm_page_t. The range should be de-registered
after consumer stopped using it.
De-inline the PHYS_TO_VM_PAGE() since it now carries code to iterate
over registered ranges.
A hash container might be developed instead of range registration
interface, and fake pages could be put automatically into the hash,
were PHYS_TO_VM_PAGE() could look them up later. This should be
considered before the MFC of the commit is done.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 1 month
size for the AR7240.
* Include SM/MS macros, thanks to ath_hal(4).
* This field is for normal packets, VLAN and other headers are added to
this by the switch device.
* Set the MTU to 1536, to match what is done in Linux. Use the SM
macro to write this field.
Obtained from: Atheros (AR7240 datasheet), Linux OpenWRT (MTU default)
vm_page into new interface vm_page_initfake(). Handle the case of fake
page re-initialization with changed memattr.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
MFC after: 1 month
This is to silence warnings that result from different definitions of
uint64_t on different architectures, specifically i386 and sparc64.
MFC after: 1 month
all integrated and on-board peripherals except the DataFlash (at91_spi(4)
and at45d(4) still need to be unb0rken) and NAND Flash (missing NAND
framework) are working.
AFAICT, this makes FreeBSD the first operating system besides Nut/OS
supporting Ethernut 5 out of tree.
* Add the i2c bitbang bus;
* Add the etherswitch/rtl8366rb drivers;
* "fix" the USB GPIO configuration so USB actually works.
Submitted by: Stefan Bethke <stb@lassitu.de>
a taskqueue.
This gives a 16% performance improvement under high load on slow systems,
especially when vr shares an interrupt with another device, which is
common with the Alix x86 boards.
Contrary to the other devices, I left the interrupt processing for loop
in because there was no significant difference in performance and this
should avoid enqueuing more taskqueues unnecessarily.
We also decided to move the vr_start_locked() call inside the for loop
because we found out that it helps performance since TCP ACKs now have a
chance to go out quicker.
Reviewed by: yongari (older version, same idea)
Discussed with: yongari, jhb
to allow drivers to handle request completion directly without passing
them to the CAM SWI thread removing extra context switch.
Modify all ATA/SATA drivers to use them.
Reviewed by: gibbs, ken
MFC after: 2 weeks
memory mapped pages being written back on an NFS mount.
Since any thread can call VOP_PUTPAGES() to write back a
dirty page, the credentials of that thread may not have
write access to the file on an NFS server. (Often the uid
is 0, which may be mapped to "nobody" in the NFS server.)
Although there is no completely correct fix for this
(NFS servers check access on every write RPC instead of at
open/mmap time), this patch avoids the common cases by
holding onto a credential that recently opened the file
for writing and uses that credential for the write RPCs
being done by VOP_PUTPAGES() for both NFS clients.
Tested by: Joel Ray Holveck (joelh at juniper.net)
PR: kern/165923
Reviewed by: kib
MFC after: 2 weeks
This way with the new zfsloader there is no need to explicitly set zfs
root filesystem either via vfs.root.mountfrom or fstab.
It should be automatically picked up from currdev which is by default
is set from bootfs.
Tested by: Florian Wagner <florian@wagner-flo.net> (x86)
MFC after: 1 month
In zfs loader zfs device name format now is "zfs:pool/fs",
fully qualified file path is "zfs:pool/fs:/path/to/file"
loader allows accessing files from various pools and filesystems as well
as changing currdev to a different pool/filesystem.
zfsboot accepts kernel/loader name in a format pool:fs:path/to/file or,
as before, pool:path/to/file; in the latter case a default filesystem
is used (pool root or bootfs). zfsboot passes guids of the selected
pool and dataset to zfsloader to be used as its defaults.
zfs support should be architecture independent and is provided
in a separate library, but architectures wishing to use this zfs support
still have to provide some glue code and their devdesc should be
compatible with zfs_devdesc.
arch_zfs_probe method is used to discover all disk devices that may
be part of ZFS pool(s).
libi386 unconditionally includes zfs support, but some zfs-specific
functions are stubbed out as weak symbols. The strong definitions
are provided in libzfsboot.
This change mean that the size of i386_devspec becomes larger
to match zfs_devspec.
Backward-compatibility shims are provided for recently added sparc64
zfs boot support. Currently that architecture still works the old
way and does not support the new features.
TODO:
- clear up pool root filesystem vs pool bootfs filesystem distinction
- update sparc64 support
- set vfs.root.mountfrom based on currdev (for zfs)
Mid-future TODO:
- loader sub-menu for selecting alternative boot environment
Distant future TODO:
- support accessing snapshots, using a snapshot as readonly root
Reviewed by: marius (sparc64),
Gavin Mu <gavin.mu@gmail.com> (sparc64)
Tested by: Florian Wagner <florian@wagner-flo.net> (x86),
marius (sparc64)
No objections: fs@, hackers@
MFC after: 1 month
