Because {NGROUPS_MAX} may become variable, its value should be obtained
using sysconf(3). If a #define is used anyway, it should be obtained by
including <limits.h> as that is in POSIX like getgroups(2) itself is.
<sys/param.h> is not in POSIX.
MFC after: 1 week
The v1 and v3 interfaces returned the whole EEPROM but the v14/v4k
interfaces just returned the base header. There's extra information
outside of that which would also be nice to get access to.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
- The mean RTT is updated at the end of each congestion epoch, but if we switch
to congestion avoidance within the first epoch (e.g. if ssthresh was primed
from the hostcache), we'll trigger a divide by zero panic in
cubic_ack_received(). Set the mean to the min in cubic_record_rtt() if the
mean is less than the min to ensure we have a sane mean for use in this
situation. This fixes the panic reported by Nick Hibma.
- Adjust conditions under which we update the mean RTT in cubic_post_recovery()
to ensure a low latency path won't yield an RTT of less than 1. This avoids
another potential divide by zero panic when running CUBIC in networks with
sub-millisecond latencies.
- Remove the "safety" assignment of min into mean when we don't update the mean
because of failed conditions. The above change to the conditions for updating
the mean ensures the safety issue is addressed and I feel it is better to keep
our previous mean estimate around if we can't update than to revert to the
min.
- Initialise the mean RTT to 1 on connection startup to act as a safety belt if
a situation we haven't considered and addressed with the above changes were to
crop up in the wild.
Sponsored by: FreeBSD Foundation
Reported and tested by: Nick Hibma
Discussed with: David Hayes <dahayes at swin edu au>
MFC after: 5 weeks
X-MFC with: r216114
hexdump.
This is a part replacement of the old athprom code, which tries
to both fetch and print the contents of an eeprom dump.
A tool to generate hexdumps from a running system will follow shortly.
* add missing includes to quieten warnings
* fix an inline function decl to have a return type
* since .h files are created during the build (opt_ah.h, ah_osdep.h)
which modify the behaviour of the HAL include/source files,
include OBJDIR in the path so the #include's work.
The tools should now build when the directory is added to LOCAL_DIRS
during a make buildworld.
value. While I'm here enable all clocks before initializing
controller. This change should fix lockup issue seen on AR8152
v1.1 PCIe Fast Ethernet controller.
PR: kern/154076
MFC after: 3 days
stack from the output of `netstat -ani'.
- The node-local multicast address in the output of `netstat -rn'
should be handled as well.
Spotted by: Bernd Walter <ticso__at__cicely7.cicely.de>
either overflow the supplied buffer, or cause uiomove fail.
Do not advance cached de when directory entry was not copied out.
Do not return EOF when no entries could be copied due to first entry
too large for supplied buffer, signal EINVAL instead.
Reported by: Beat G?tzi <beat chruetertee ch>
MFC after: 1 week
This is apparently an AR9285 with the 802.11n specific bits disabled.
This code is completely untested; I'm doing this in response to users
who wish to test the functionality out. It's likely as buggy as the
AR9285 support is in FreeBSD at the moment.
sys/dev/ath/ath_hal/ar5416/ is getting very crowded and further
commits will make it even more crowded. Now is a good time to
shuffle these files out before any more extensive work is done
on them.
Create an ar9003 directory whilst I'm here; ar9003 specific
chipset code will eventually live there.
with these ADC DC Gain/Offset calibrations.
The whole idea is to calibrate a pair of ADCs to compensate for any
differences between them.
The AR5416 returns lots of garbage, so there's no need to do the
calibration there.
The AR9160 returns 0 for secondary ADCs when calibrating 2.4ghz 20mhz
modes. It returns valid data for the secondary ADCs when calibrating
2.4ghz HT/40 and any 5ghz mode.
This removes the chipset-dependent TX DMA completion descriptor groveling.
It should now be (more) portable to other, later atheros chipsets when the
time comes.
- Remove sys/conf/ldscript.mips.64 and sys/conf/ldscript.mips.n32 and use
ldscript.mips for all ABIs. The default OUTPUT_FORMAT of the toolchain
is correct.
- Remove LDSCRIPT_NAME entires from XLR n32 and n64 conf files.
- Remove TARGET_BIG_ENDIAN from XLR conf files.
- Fix machine entry in XLRN32
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
