redundant malloc/free. Add comments about how this should really be
done. Fix an overly verbose comment about under 1MB mapping: go ahead
and set the bits, but we ignore them.
- If the flag is set and auto-select fails, assume disk is not present.
- Set disk empty flag only when the floppy controller reset is needed.
It fixes regression introduced in r1.311, which prevented it from ignoring
errors. Now fdformat(1) and dd(1) with conv=noerror option can continue
when read/write errors occur as they should.
- Do not retry disk probing as it is extremely slow and pointless.
- Move the disk probing code into a separate function.
- Do not reset disk empty flag if write-protect check fails somehow.
PR: kern/116538[1]
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
can be controlled by ifconfig(8). Note, VLAN hardware tagging
controls still lacks required handler but it requires more driver
cleanups so I didn't touch that part.
PR: kern/128766
- Fix to ioctl path in which the length could be 0 which means
no data in/out from LSI.
- Fix to ioctl path in which the data in the sense data space
of the ioctl packet is a really a pointer to some location in
user-space. From LSI re-worked a bit by me.
- Add HW support for next gen cards from LSI.
Thanks to LSI for their support!
Submitted by: jhb, LSI
MFC after: 3 days
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
- Do not let individual KLD module unregister firmware image loaded by ispfw
or vice versa.
- Make 'kldunload ispfw' actually unregister all firmware images loaded by
ispfw, not just 'isp_1040'.
- Print which KLD module actually loaded the firmware image.
- Remove unused return value from do_load_fw() and do_unload_fw() and remove
duplicate sys/param.h while I am here.
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
On RELENG_6 (and probably RELENG_7) we see our syscons windows and
pseudo-terminals have the following buffer sizes:
| LINE RAW CAN OUT IHIWT ILOWT OHWT LWT COL STATE SESS PGID DISC
| ttyv0 0 0 0 7680 6720 2052 256 7 OCcl 1146 1146 term
| ttyp0 0 0 0 7680 6720 1296 256 0 OCc 82033 82033 term
These buffer sizes make no sense, because we often have much more output
than input, but I guess having higher input buffer sizes improves
guarantees of the system.
On MPSAFE TTY I just sent both the input and output buffer sizes to 7
KB, which is pretty big on a standard FreeBSD install with 8 syscons
windows and some PTY's. Reduce the baud rate to 9600 baud, which means
we now have the following buffer sizes:
| LINE INQ CAN LIN LOW OUTQ USE LOW COL SESS PGID STATE
| ttyv0 1920 0 0 192 1984 0 199 7 2401 2401 Oil
| pts/0 1920 0 0 192 1984 0 199 5631 1305 2526 Oi
This is a lot smaller, but for pseudo-devices this should be good
enough. You need to do a lot of punching to fill up a 7.5 KB input
buffer. If it turns out things don't work out this way, we'll just
switch to 19200 baud.
NATM needs 'struct in_addr' to compile, which is a problem on its own
but include in.h for now if we have NATM but neither INET or INET6.
MFC after: 2 months
the sc does not have 'an_have_rssimap' variable.
Add an ANCACHE check to poperly hide the case and make an(4)
compile without INET.
MFC after: 2 months
Because the TTY hooks interface was not finished when I imported the
MPSAFE TTY layer, I had to disconnect the snp(4) driver. This snp(4)
implementation has been sitting in my P4 branch for some time now.
Unfortunately it still doesn't use the same error handling as snp(4)
(returning codes through FIONREAD), but it should already be usable.
I'm committing this to SVN, hoping someone else could polish off its
rough edges. It's always better than having a broken driver sitting in
the tree.
Note that these changes will not make the driver work on powerpc, but it should fix at least the i386/amd64 cases.
Obtained from: //depot/projects/usb/src/sys/dev/usb2/wlan/if_zyd2.c#20
Noticed by: jeli, ed
vnode in question does not need to be held. All the data structures used
during the name lookup are protected by the global name cache lock.
Instead, the caller merely needs to ensure a reference is held on the
vnode (such as vhold()) to keep it from being freed.
In the case of procfs' <pid>/file entry, grab the process lock while we
gain a new reference (via vhold()) on p_textvp to fully close races with
execve(2).
For the kern.proc.vmmap sysctl handler, use a shared vnode lock around
the call to VOP_GETATTR() rather than an exclusive lock.
MFC after: 1 month
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
allocating resources to read the CIS. I'm not sure when this changed,
but it is totally wrong. Also, add a minor improvement to the
debugging.
This should help everybody trying to run dumpcis on atheros wireless
card as well.
MFC after: 2 days
right... Good thing the size was ignored...
Where this macro is used, there's no reason to do it anyway. There
seems to have been some old-time confusion between the CIS pointer
definition, and the BAR definitions at the base of this bug.
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
For an unknown reason the touch pad of my PowerBook generates button 5
events when you operate it. This causes the adb_mouse code to convert
them to button 2 events, which is not what we want.
Add a new flag, AMS_TOUCHPAD, which is used to distinguish the touch
pad. When set, don't convert button events of unknown buttons to the
last button.
There are still three problems left with respect to user input:
- The mouse button events are not properly processed when the touch pad
isn't touched.
- The arrow keys on the keyboard don't work inside X11.
- The power button isn't handled by the kernel, similar to the ACPI
power button on i386/amd64.
Approved by: nwhitehorn
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
Right now ams_read() uses cv_wait() to wait for new data to arrive on
the mouse device. This means that when you run `cat /dev/ams0', it
cannot be interrupted directly. After you press ^C, you first need to
move the mouse before cat will quit. Make this function use
cv_wait_sig(), which allows it to be interrupted directly.
Reviewed by: nwhitehorn
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
sdhci supports up to 65535 blocks transfers, at91_mci - one block.
Enable multiblock operations disabled before to follow at91_mci driver
limitations.
Reviewed by: imp@
driver (rev 1.3), by Joerg Sonnenberger.
Note: This change is untested as I do not own the hardware. Let me know
if things work or do not work for you by sending me the output dmesg (and
usbctl -f /dev/usbX if possible). Thanks.
for the BCM5714 revision A0 when in a multi-port configuration
and unconditionally for the remainder of the class of BCM575X
and beyond chips.
This was prodded by mav and is based on a suggestion and a
patch submitted by jhb.
Reviewed by: jhb
MFC after: 2 months
rs400/rs480 should clear the RADEON_BUS_MASTER_DIS bit. This should get
the rs485 IGP chips going again.
Approved by: jhb (mentor)
Obtained from: drm git master
making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
o update tx rssi data only when an ACK was received
o return tx rssi from sampled data instead of the last frame
o track noise floor
o return rx rssi and noise floor (was broken)
o pass country code, outdoor indication, and ecm mode into the hal
when requesting a channel list
o add a console msg when regulatory setup fails
o add placeholder code to map between Atheros sku's and 802.11 sku's
that handles only the debug country code used to unlock the full
channel list (to be used only for debugging)
o fix multiple instances of mismapping the 802.11 location to the
outdoor indication (anywhere may be outdoor also)
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
The cn_unit and cn_tp fields don't seem to be used anywhere. Some
drivers set them, while others don't. Just remove them, in an attempt to
make our consdev code a little easier to understand.
G3 as well as the internal ADB keyboard and mice in PowerBooks and iBooks. This
also brings in Mac GPIO support, for which we should eventually have a better
interface.
Obtained from: NetBSD (CUDA and PMU drivers)
Olaf Kirch noticed that the i915_set_status_page() function of the i915
kernel driver calls ioremap with an address offset that is supplied by
userspace via ioctl. The function zeroes the mapped memory via memset
and tells the hardware about the address. Turns out that access to that
ioctl is not restricted to root so users could probably exploit that to
do nasty things. We haven't tried to write actual exploit code though.
It only affects the Intel G33 series and newer.
Approved by: bz (secteam)
Obtained from: Intel drm repo
Security: CVE-2008-3831
