request could be deallocated before the top half had finished
issuing it. The problem seems only to happen with IDE drives
and vn devices, but theoretically it could happen with any
drive. This is the most important part of a possible series
of fixes designed to remove race conditions without locking
out interrupts for longer than absolutely necessary.
Reported-by: sos
Fix-supplied-by: dillon
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
connected during boot and the vpo module is in the kernel/loaded.
In the case where the module is loaded at some later stage with kldload,
the CAM bus is now rescanned as well.
- The driver now uses bus_space() and runs on NetBSD 1.4.2
Submitted by Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
- Remove startup quirks for video and vbi capture for PAL users.
PAL TV users can now run FXTV and Alevt in any order.
- Add support for cable channels >100
Submitted by Scott Presnell <srp@zgi.com>
- New MSP3410/3415 setup code added. This is experimental.
Please set the sysctl hw.bt848.slow_msp_audio to 1 for this.
Submitted by Frank Nobis<fn@radio-do.de>
Pass sc->dev rather than a bogusly cast pccard_softc *sc.
This allows us to insert and remove cards w/o panicing the kernel.
However, the cis isn't mapped in, so the pccard_scan_cis function
fails.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
(Much of this done by script)
Move B_ORDERED flag to b_ioflags and call it BIO_ORDERED.
Move b_pblkno and b_iodone_chain to struct bio while we transition, they
will be obsoleted once bio structs chain/stack.
Add bio_queue field for struct bio aware disksort.
Address a lot of stylistic issues brought up by bde.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
introduced in FreeBSD-4.0. The driver is now full up-to-date
with regards to the current kernel interfaces.
Another significant change in this driver version applies
to the checking of the data direction. The driver is now
able to check against the expected data direction in any
circumstance and will not hang either if direction is wrong
at the start of the IO, or if for some weird reason,
the device changes to the wrong direction during the IO.
This driver version is still usable under FreeBSD 3.2/3.3,
since it only requires CAM, other kernel interface dependencies
being #if'ed in the sources according to kernel version.
But, in order to use the driver under those early kernel
versions, user has to move the driver sources by hand and make
appropriate tiny changes to let the kernel know about the driver.
Other changes:
- Remove the debugging stuff for WSR bit.
- Get rid of some warnings about volatile being discarded.
which think they know the IntelliMouse 4-byte packet and believe,
wrongly, that any other protocols use 3-byte packets.
- Update a couple of comment lines for A4 Tech mice.
conf/files
i don't seem to be clearing the cache right resulting in a short initial
burst of noise, despite doing the same as creative and alsa. i'm committing
now so more eyes can pore over the code.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
doesn't support winmodems, softmodems, hcf or any other modem that
relies on the host to do any sort of soft control for any aspect of
the modem's function. There are two modems known to work:
3COM FaxModem PCI.
ActionTec 56k VoiceMessaging PCI Modem
and the following modem might work
Multitech PCI FaxModem (not sure about this)
and the serial pci cards might work too. I have neither these
hardware items so I can't add support for them.
- Add periodic status monitoring routine. Currently just detects
lost commands, further functionality pending data from AMI.
Add some new commands states; WEDGED (never coming back) and
LATE (for when a command that wasmarked as WEDGED comes bacj,
- Remove a number of redundant efforts to poll the card for completed
commands. This is what interrupt handlers are for.
- Limit the maximum number of outstanding I/O transactions. It seems
that some controllers report more than they can really handle,
and exceding this limit can cause the controller to lock up.
- Don't use 'wait' mode for anything where the controller might not
be able to generate interrupts. (Keep the 'wait' mode though sa it
will become useful when we start taking userspace commands.
- Use a similar atomic locking trategy to the Mylex driver to prevent
some reentrancy problems.
- Correctly calculate the block count for non-whoile-bloch transfers
(actually illegal).
- Use the dsik device's si_drv1 field instead of b_driver1 in the
buf struct to pass the driver identifier arond.
- Rewrite amr_start and amr_done() along the lines of the Mylex driver
in order to improve robustnes.
- Always force the PCI busmaster bit on.
- Move dev/aic/aic_isa.c entry from conf/files to conf/files.MACHINE
because PC-98 uses different file.
Submitted by: nyan and IMAI Takeshi <take-i@ceres.dti.ne.jp>
fe_read_eeprom_rex() and fe_init_rex(). These functions should be
useful for REX-5580 series (for PC-AT). But they are included in
`#ifdef PC98' to avoid warnings by unused static functions. If you
try to support REX-5580, please be aware of these functions.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
rewrite ess mixer to use native registers
rewrite play/rec code to use more accurate timer when available
add code to use audio2 for playback, but disable it as no irqs are generated
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
address size that is different than the standard 6bits. This fixes
support for the Compaq NC3121 card, certain newer Intel Pro/100+
cards, and should also fix integrated NICs on SuperMicro and Compaq
motherboards.
The auto-sizing algorithm was taken from NetBSD (thanks!), which I
think got it from Linux originally.
Thanks also to Andrew Sparrow <spadger@best.com> and Joe Moore
<jomor@ahpcns.com> for supplying me with unworking Compaq and Intel
cards to develop and test the fixes with.
set properly in the struct buf with vinum:
Fix locations where B_READ was cleared in the old code but
b.b_iocmd wasn't set to BIO_WRITE
Fix propogation of b_iocmd
Correct comments to reflect reality
Don't compare b_flags with BIO_READ, it's in b_iocmd.
Submitted by: Bernd Walter <ticso@cicely.de>
Remove RF_PCCARD_ATTR in anticipation of removing it from sys/rman.h
Add interface for setting "attributes" of pccard/cardbus devices.
Minor formatting nits.
timeout closer to the 1-second value that AMI use in their Linux
driver, and mark the mailbox structures as volatile so that gcc
doesn't over-optimise access to them.
This should fix the "controller wedged" bug.
Submitted by: Brian Dean <brdean@unx.sas.com>
* add a callback for initialising the mixer interface
* support ac97 2.1 variable rate audio feature
fix ac97-using drivers for the above
add suspend/resume support for neomagic
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
substitute BUF_WRITE(foo) for VOP_BWRITE(foo->b_vp, foo)
substitute BUF_STRATEGY(foo) for VOP_STRATEGY(foo->b_vp, foo)
This patch is machine generated except for the ccd.c and buf.h parts.
field in struct buf: b_iocmd. The b_iocmd is enforced to have
exactly one bit set.
B_WRITE was bogusly defined as zero giving rise to obvious coding
mistakes.
Also eliminate the redundant struct buf flag B_CALL, it can just
as efficiently be done by comparing b_iodone to NULL.
Should you get a panic or drop into the debugger, complaining about
"b_iocmd", don't continue. It is likely to write on your disk
where it should have been reading.
This change is a step in the direction towards a stackable BIO capability.
A lot of this patch were machine generated (Thanks to style(9) compliance!)
Vinum users: Greg has not had time to test this yet, be careful.
too many, so I removed the checks for the valid OUIs. We already do a
checksum of the entire ethernet address, so extra checking against the
OUI shouldn't be needed.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
prevent a page fault if the card is ejected while BPF is in use. This
could happen if DHCP or tcpdump was in use on that interface during
ejection. Other drivers may also require this modification.
Reviewed by: wes
negotiation features (DT, ULTRA2, ULTRA, FAST). The offsets
where not properly updated when the DT entry was added and so
the driver could attempt to negotiate a speed faster than that
supported by the target device or even requested by the user
via SCSI-Select settings. *
o Update the target mode incoming command queue kernel index value
ever 128 commands instead of 32. This means that the kernel will
always try to keep its index (as seen on the card - the kernel may
actually have cleared more space) 128 commands ahead of where the
sequencer is adding entries.
o Use the HS_MAILBOX register instead of the KERNEL_TQINPOS location
in SRAM to indicate the kernel's target queue possition on Ultra2
cards. This avoids the "pause bug" on these cards and also turns
out to be much more efficient.
o When enabling or disabling a particular target id for target mode,
make sure that the taret id in the SCSIID register does not
reference an ID that is not to receive target selections. This
is only an issue on chips that support the multiple target id
feature where the value in SCSIID will still affect selection
behavior regardless of the values in the target id bit field
registers.
o Remove some target mode debugging printfs.
o Make sure that the sense length reported in ATIO commands is
always zero. This driver does not, yet, report HBA generated
sense information for accepted commands.
o Honor the CAM_TIME_INFINITY and CAM_TIME_DEFAULT values for
the CCB timeout field.
o Make the driver compile with AHC_DEBUG again.
* Noticed by: Andrew Gallatin<gallatin@cs.duke.edu>
-current. It doesn't work yet as stable as the 3.x/PAO version of the
driver does, however, i get occasional `FDC direction bit not set' and
other weird messages, but it basically works at least.
The old (defunct) #ifdef FDC_YE stuff has been eliminated completely
now, PCMCIA-FDC specific functions have been implemented differently
where needed.
Unfortunately, due to the fact that the traditional PeeCee FDC with
its funny non-contiguous register space (one register for WD1003
harddisk controllers is interleaved into the FDC register set), and
Peter's subsequent changes involving two different bus space handles
for normal FDCs, the changes required for the Y-E stuff are more
complex than i'd love them to be. I've done my best to keep the logic
for normal FDCs intact.
Since the Y-E FDC seems to lose interrupts after a FDC reset
sometimes, i've also replaced the timeout logic in fd_turnoff() to
generate an artificial pseudo interrupt in case of a timeout while the
drive has still outstanding transfers waiting. This avoids the total
starvation of the driver that could be observed with highly damaged
media under 3.x/PAO. This part of the patch has been revied by bde
previously.
I've fixed a number of occasions where previous commits have been
missing the encapuslation of ISA DMA related functions inside
FDC_NODMA checks.
I've added one call to SET_BCDR() during preparation of the format
floppy operation. Floppy formatting has been totally broken before in
3.x/PAO (garbage ID fields have been written to the medium, causing
`wrong cylinder' errors upon media reading). This is just black
magic, i don't have the slightes idea _why_ this needs to be but just
copied over the hack that has been used by the PAO folks in the normal
read/write case anyway.
The entired device_busy() stuff seems to be pointless to me. In any
case, i had to add device_unbusy() calls symmetrical to the
device_busy() calls, otherwise the PCMCIA floppy driver could never be
deactivated. (As it used to be, it caused a `mark the device busier
and busier' situation.) IMHO, all block device drivers should be
marked busy based on active buffers still waiting for the driver, so
the device_unbusy() calls should probably go to biodone(). Only one
other driver (whose name escapes me at the moment) uses device_busy()
calls at all, so i question the value of all this...
I think this entire `device busy' logic simply doesn't fit for PCMCIA
&al. It cannot be the decision of some piece of kernel software to
declare a device `busy by now, you can't remove it', when the actual
physical power of removing it is the user pulling the card. The
kernel simply has to cope with the removal, however busy the device
might have been by the time of the removal, period. Perhaps a force
flag needs to be added?
Upon inserting the card a second time, i get:
WARNING: "fd" is usurping "fd"'s cdevsw[]
WARNING: "fd" is usurping "fd"'s bmaj
I suspect this is related to the XXX comment at the call to
cdevsw_add(). Does anybody know what the correct way is to cleanup
this?
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
- Properly keep track of resources (I/O ports and irq).
- Use bus_space_read/write() to access the ports.
- Add PnP IDs.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).
this version include:
- Support for version 2.x firmware (2.42 or later recommended). This
means we are the only open-source driver supporting these adapters.
This code has only been tested on a Digital KZPCA adapter in an Alpha
system, but is believed to be correct. NOTE: EISA adapters are not
yet supported.
- Support the BIOS/Firmware initialisation handshake protocol. This
allows the driver to bring the card up to operational state even if
the BIOS can't be run (eg. if it's an x86 BIOS in an Alpha system).
- A working command pasthrough interface. This allows a user-space
configuration tool (under development) to issue arbitrary commands
to the controller or to devices in the system.
platform we're running on so we know how many bits to reserve at the top
end for the 'hose' value. It turns out that there's *just* enough room
to support all possible hoses on TurboLaser.
Reviewed by: gallatin@freebsd.org, dfr@free3bsd.org
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
rest of the code in (so changing media actually works.)
Add a few more register definitions for use with this and other new code.
Print a few details in the probe message; this should be useful in
bug reports and such but should not add to the clutter.
* i needed it anyway
* remove startccs and startcmd - done
* as those were used for the NetBSD start timeout
* multicast - done but UNTESTED
* I don't have the ability/facilty to test this
* rxlevel - done
* stats reported via raycontrol
* getparams ioctl - done
* reported via raycontrol
* start_join_done needs a restart in download_done - done
* now use netbsd style start up
removed spare timerh
implemented start_assoc in ray_ccs_done
bit more knfing
we get the com address. If so, we go ahead and return. Bruce thinks
there's a bug in the pccard layer that it terminates devices with
extreme prejustice rather than letting them deside for themselves when
to terminate (and he's likely right). This fix doesn't change that,
but instead works around it by checking for NULL pointers at more
places than before.
The detach routine still calls functions at interrupt level that
aren't reentrant. In theory this could cause a problem, but none
showed up in practice. Future versions should correct this problem,
likely by making the detach process a thread/process at the pccard
level. NEWCARD will do this, and the current pccard layer should
likely be modified to that as well, should it live long enough.
A few style nits of the same form that were in my original patch sent
off to bde were also fixed as part of this process. Mostly use of
!ptr and return ENOPARENS.
This should prevent a crash on suspend with an active ppp link as
well, but that wasn't tested.
Reviewed by: bde
Approved by: jkh
requires current and desired network parameters, so I have created a network parameter structure and used two on them in the softc. This gives a bit of room of expansion. Re-wrote the update check in _net to work with this.
Tidyed up softc due to above.
Removed startccs and startcmd as they were only used by NetBSDs startup timeout.
keyboard port and interrupt is enabled and the driver is attached even
when the keyboard itself is not present when the system is booting.
(This has been the behavior through out 2.X and 3.X, but is somehow
broken in 4.0.)
# I certainly don't recommend people to `hot-plug' the AT keyboard,
# because the interface isn't designed for hot-plugging and such act
# will often break the keyboard controller. But, so many people want to
# do that anyway...
Approved by: jkh
