This fixes when an IP address mapping is put in the hostmap table for
sticky NAT rules, it ends up having the wrong byte order.
Obtained from: ipfilter CVS repo (r1.102), NetBSD CVS repo (r1.12)
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
struct ifnet if_oqdrops.
Some netgraph modules used ifqueue w/o ifnet. Accounting of queue drops
is simply removed from them. There were no API to read this statistic.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
hardware driver update from Mellanox Technologies.
- Remove empty files from the OFED Linux Emulation layer.
- Fix compile warnings related to printf() and the "%lld" and "%llx"
format specifiers.
- Add some missing 2-clause BSD copyrights.
- Add "Mellanox Technologies, Ltd." to list of copyright holders.
- Add some new compatibility files.
- Fix order of uninit in the mlx4ib module to avoid crash at unload
using the new module_exit_order() function.
MFC after: 1 week
Sponsored by: Mellanox Technologies
If powersave is enabled and there are any transitions to network
or full sleep - even if they're pretty damned brief - eventually
something messes up somewhere and the bus glue between the AR9331
SoC and the AR9331 wifi stops working. It shows up as stuck DMA
and LOCAL_TIMEOUT interrupts.
Both ath9k and the reference driver does a full chip reset if things
get stuck.
So:
* teach the AR9330 HAL about the force_full_reset option I added a
couple of years ago;
* if the chip is currently in full-sleep, do a full-reset;
* if TX DMA and/or RX DMA are still enabled (eg, they did get
stuck during reset) then do a full-reset.
Tested:
* AR9331 SoC, STA mode
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
This is loosly based on Xorg changeset f57bc0e by Christian
Zander.
Submitted by: Wolf Ramovsky <wolf.ramovsky gmail.com>
via core (peter)
MFC after: 2 weeks
to be consistent with mutex destruction in ipf_log_soft_destroy(). As a
result mutex destruction in ipf_log_soft_fini() is redundant.
Approved by: glebius (mentor)
Obtained from: darrenr (author)
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
ip_auth.c to ip_auth.h. ip_frag_soft_t moves from ip_frag.c to
ip_frag.h. mlfk_ipl.c creates sysctl MIBs that reference control blocks
that are dynamically created when IP Filter is loaded. This necessitated
creating them on-the-fly rather than statically at compile time.
Approved by: glebius (mentor)
Import xz-embedded from git.
This is from commit hash '6a8a2364434763a033781f6b2a605ace9a021013'.
This makes it possible to use CRC64 but for now it's intentionally
not added to build.
- Use counter(9) for rt_pksent (former rt_rmx.rmx_pksent). This
removes another cache trashing ++ from packet forwarding path.
- Create zini/fini methods for the rtentry UMA zone. Via initialize
mutex and counter in them.
- Fix reporting of rmx_pksent to routing socket.
- Fix netstat(1) to report "Use" both in kvm(3) and sysctl(3) mode.
The change is mostly targeted for stable/10 merge. For head,
rt_pksent is expected to just disappear.
Discussed with: melifaro
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
in net, to avoid compatibility breakage for no sake.
The future plan is to split most of non-kernel parts of
pfvar.h into pf.h, and then make pfvar.h a kernel only
include breaking compatibility.
Discussed with: bz
- Provide pf_altq.h that has only stuff needed for ALTQ.
- Start pf.h, that would have all constant values and
eventually non-kernel structures.
- Build ALTQ w/o pfvar.h, include if_var.h, that before
came via pollution.
- Build tcpdump w/o pfvar.h.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
