including the include directive.
Fix minor build issue corrected by converting yypush_buffer_state and
yypop_buffer_state to yy_set_buffer_state and a hard-coded 100-deep
stack. It was easier to fix it here than to import that support into
our flex.
The new tools and test hardness remain unsupported at the moment.
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
date: 2010/12/24 20:12:56; author: henning; state: Exp; lines: +3 -3
in pf_src_connlimit, the indices to sk->addr were swapped.
tracked down and diff sent by Robert B Mills <rbmills at sdf.lonestar.org>
thanks, very good work! ok claudio
Impact is that the "flush" keyword didn't work.
Obtained from: OpenBSD
MFC after: 1 week
Cleaner solution (e.g. adding another header) should be done here.
Original log:
Move several enums and structures required for L2 filtering from ip_fw_private.h to ip_fw.h.
Remove ipfw/ip_fw_private.h header from non-ipfw code.
Requested by: luigi
Approved by: kib(mentor)
sys/contrib/rdma/rdma_cma.c:1259:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNRESET:
^
@/sys/errno.h:118:20: note: expanded from macro 'ECONNRESET'
#define ECONNRESET 54 /* Connection reset by peer */
^
sys/contrib/rdma/rdma_cma.c:1263:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ETIMEDOUT:
^
@/sys/errno.h:124:19: note: expanded from macro 'ETIMEDOUT'
#define ETIMEDOUT 60 /* Operation timed out */
^
sys/contrib/rdma/rdma_cma.c:1260:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNREFUSED:
^
@/sys/errno.h:125:22: note: expanded from macro 'ECONNREFUSED'
#define ECONNREFUSED 61 /* Connection refused */
^
This is because the switch uses iw_cm_event::status, which is an enum
iw_cm_event_status, while ECONNRESET, ETIMEDOUT and ECONNREFUSED are
just plain defines from errno.h.
It looks like there is only one use of any of the enumeration values of
iw_cm_event_status, in:
sys/contrib/rdma/rdma_iwcm.c: if (iw_event->status == IW_CM_EVENT_STATUS_ACCEPTED) {
So messing around with the enum definitions to fix the warning seems too
disruptive; the simplest fix is to cast the argument of the switch to
int.
Reviewed by: kmacy
MFC after: 1 week
revision 1.173
date: 2011/11/09 12:36:03; author: camield; state: Exp; lines: +11 -12
State expire time is a baseline time ("last active") for expiry
calculations, and does _not_ denote the time when to expire. So
it should never be added to (set into the future).
Try to reconstruct it with an educated guess on state import and
just set it to the current time on state updates.
This fixes a problem on pfsync listeners where the expiry time
could be double the expected value and cause a lot more states
to linger.
forwarding a packet, that creates state, until
pfsync(4) peer acks state addition (or 10 msec
timeout passes).
This is needed for active-active CARP configurations,
which are poorly supported in FreeBSD and arguably
a good idea at all.
Unfortunately by the time of import this feature in
OpenBSD was turned on, and did not have a switch to
turn it off. This leaked to FreeBSD.
This change make it possible to turn this feature
off via ioctl() and turns it off by default.
Obtained from: OpenBSD
Revert r233555 and apply a fix for the reference counting regressions.
Tested by: andreast, lme, nwhitehorn,
Sevan / Venture37 (venture37 at gmail dot com)
Submitted by: Robert Moore (robert dot moore at intel dot com)
Temporarily revert an upstream commit. This change caused regressions for
too many laptop users. Especially, automatic repair for broken _BIF caused
strange reference counting issues and kernal panics. This reverts:
c995fed15a
make use of it where possible.
This primarily brings in support for newer hardware, and FreeBSD is not yet
able to support the abundance of IRQs on new hardware and many features in the
Ethernet driver.
Because of the changes to IRQs in the Simple Executive, we have to maintain our
own list of Octeon IRQs now, which probably can be pared-down and be specific
to the CIU interrupt unit soon, and when other interrupt mechanisms are added
they can maintain their own definitions.
Remove unmasking of interrupts from within the UART device now that the
function used is no longer present in the Simple Executive. The unmasking
seems to have been gratuitous as this is more properly handled by the buses
above the UART device, and seems to work on that basis.
revision 1.146
date: 2010/05/12 08:11:11; author: claudio; state: Exp; lines: +2 -3
bzero() the full compressed update struct before setting the values.
This is needed because pf_state_peer_hton() skips some fields in certain
situations which could result in garbage beeing sent to the other peer.
This seems to fix the pfsync storms seen by stephan@ and so dlg owes me
a whiskey.
I didn't see any storms, but this definitely fixes a useless memory
allocation on the receiving side, due to non zero scrub_flags field
in a pfsync_state_peer structure.
Extend the so far IPv4-only support for multiple routing tables (FIBs)
introduced in r178888 to IPv6 providing feature parity.
This includes an extended rtalloc(9) KPI for IPv6, the necessary
adjustments to the network stack, and user land support as in netstat.
Sponsored by: Cisco Systems, Inc.
Reviewed by: melifaro (basically)
MFC after: 10 days
M_NOWAIT. Currently, the code allows for sleeping in the ioctl path
to guarantee allocation. However code also handles ENOMEM gracefully, so
propagate this error back to user-space, rather than sleeping while
holding the global pf mutex.
Reviewed by: glebius
Discussed with: bz
- Define schednetisr() to swi_sched.
- In the swi handler check if there is some data prepared,
and if true, then call pfsync_sendout(), however tell it
not to schedule swi again.
- Since now we don't obtain the pfsync lock in the swi handler,
don't use ifqueue mutex to synchronize queue access.
revision 1.128
date: 2009/08/16 13:01:57; author: jsg; state: Exp; lines: +1 -5
remove prototypes of a bunch of functions that had their implementations
removed in pfsync v5.
o Make the pfsync.ko actually usable. Before this change loading it
didn't register protosw, so was a nop. However, a module /boot/kernel
did confused users.
o Rewrite the way we are joining multicast group:
- Move multicast initialization/destruction to separate functions.
- Don't allocate memory if we aren't going to join a multicast group.
- Use modern API for joining/leaving multicast group.
- Now the utterly wrong pfsync_ifdetach() isn't needed.
o Move module initialization from SYSINIT(9) to moduledata_t method.
o Refuse to unload module, unless asked forcibly.
o Improve a bit some FreeBSD porting code:
- Use separate malloc type.
- Simplify swi sheduling.
This change is probably wrong from VIMAGE viewpoint, however pfsync
wasn't VIMAGE-correct before this change, too.
Glanced at by: bz
destroyed prior to pfsync_uninit(). To do this, move all the
initialization to the module_t method, instead of SYSINIT(9).
o Fix another panic after module unload, due to not clearing the
m_addr_chg_pf_p pointer.
o Refuse to unload module, unless being unloaded forcibly.
o Revert the sub argument to MODULE_DECLARE, to the stable/8 value.
This change probably isn't correct from viewpoint of VIMAGE, but
the module wasn't VIMAGE-correct before the change, as well.
Glanced at by: bz
revision 1.170
date: 2011/10/30 23:04:38; author: mikeb; state: Exp; lines: +6 -7
Allow setting big MTU values on the pfsync interface but not larger
than the syncdev MTU. Prompted by the discussion with and tested
by Maxim Bourmistrov; ok dlg, mpf
Consistently use sc_ifp->if_mtu in the MTU check throughout the
module. This backs out r228813.
value used in sys/ofed/include/linux/netdevice.h), so there will be no
buffer overruns in the rest of the inline functions in this file.
Reviewed by: kmacy
MFC after: 1 week
revision 1.122
date: 2009/05/13 01:01:34; author: dlg; state: Exp; lines: +6 -4
only keep track of the number of updates on tcp connections. state sync on
all the other protocols is simply pushing the timeouts along which has a
resolution of 1 second, so it isnt going to be hurt by pfsync taking up
to a second to send it over.
keep track of updates on tcp still though, their windows need constant
attention.
revision 1.120
date: 2009/04/04 13:09:29; author: dlg; state: Exp; lines: +5 -5
use time_uptime instead of time_second internally. time_uptime isnt
affected by adjusting the clock.
revision 1.175
date: 2011/11/25 12:52:10; author: dlg; state: Exp; lines: +3 -3
use time_uptime to set state creation values as time_second can be
skewed at runtime by things like date(1) and ntpd. time_uptime is
monotonic and therefore more useful to compare against.
revision 1.118
date: 2009/03/23 06:19:59; author: dlg; state: Exp; lines: +8 -6
wait an appropriate amount of time before giving up on a bulk update,
rather than giving up after a hardcoded 5 seconds (which is generally much
too short an interval for a bulk update).
pointed out by david@, eyeballed by mcbride@
revision 1.171
date: 2011/10/31 22:02:52; author: mikeb; state: Exp; lines: +2 -1
Don't forget to cancel bulk update failure timeout when destroying an
interface. Problem report and fix from Erik Lax, thanks!
Start a brief note of revisions merged from OpenBSD.
7.x, 8.x and 9.x with pf(4) imports: pfsync(4) should suppress CARP
preemption, while it is running its bulk update.
However, reimplement the feature in more elegant manner, that is
partially inspired by newer OpenBSD:
- Rename term "suppression" to "demotion", to match with OpenBSD.
- Keep a global demotion factor, that can be raised by several
conditions, for now these are:
- interface goes down
- carp(4) has problems with ip_output() or ip6_output()
- pfsync performs bulk update
- Unlike in OpenBSD the demotion factor isn't a counter, but
is actual value added to advskew. The adjustment values for
particular error conditions are also configurable, and their
defaults are maximum advskew value, so a single failure bumps
demotion to maximum. This is for POLA compatibility, and should
satisfy most users.
- Demotion factor is a writable sysctl, so user can do
foot shooting, if he desires to.
of scheduling next run pfsync_bulk_update(), pfsync_bulk_fail()
was scheduled.
This lead to instant 100% state leak after first bulk update
request.
- After above fix, it appeared that pfsync_bulk_update() lacks
locking. To fix this, sc_bulk_tmo callout was converted to an
mtx one. Eventually, all pf/pfsync callouts should be converted
to mtx version, since it isn't possible to stop or drain a
non-mtx callout without risk of race.
- Add comment that callout_stop() in pfsync_clone_destroy() lacks
locking. Since pfsync0 can't be destroyed (yet), let it be here.
The root of problem is re-locking at the end of pfsync_sendout().
Several functions are calling pfsync_sendout() holding pointers
to pf data on stack, and these functions expect this data to be
consistent.
To fix this, the following approach was taken:
- The pfsync_sendout() doesn't call ip_output() directly, but
enqueues the mbuf on sc->sc_ifp's interfaces queue, that
is currently unused. Then pfsync netisr is scheduled. PF_LOCK
isn't dropped in pfsync_sendout().
- The netisr runs through queue and ip_output()s packets
on it.
Apart from fixing race, this also decouples stack, fixing
potential issues, that may happen, when sending pfsync(4)
packets on input path.
Reviewed by: eri (a quick review)
number of packets can be queued on sc, while we are in ip_output(), and then
we wipe the accumulated sc_len. On next pfsync_sendout() that would lead to
writing beyond our mbuf cluster.
to document where we are expecting to be called with a lock held to
more easily catch unnoticed code paths.
This does not neccessarily improve locking in pfsync, it just tries
to avoid the panics reported.
PR: kern/159390, kern/158873
Submitted by: pluknet (at least something that partly resembles
my patch ignoring other cleanup, which I only saw
too late on the 2nd PR)
MFC After: 3 days
and virtualization it is not helpful but complicates things.
Current state of art is to not virtualize these kinds of locks -
inp_group/hash/info/.. are all not virtualized either.
MFC after: 3 days
pfsync also depends on pf to be initialized already so pf goes at
FIRST and the interfaces go at ANY.
Then the (VNET_)SYSINIT startups for pf stays at SI_SUB_PROTO_BEGIN
and for pfsync we move to the later SI_SUB_PROTO_IF.
This is not ideal either but at least an order that should work for
the moment and can be re-fined with the VIMAGE merge, once this will
actually work with more than one network stack.
MFC after: 3 days
and never remove state.
This fixes the problem some people are seeing that state is removed when pf
is loaded as a module but not in situations when compiled into the kernel.
Reported by: many on freebsd-pf
Tested by: flo
MFC after: 3 days
hash install, etc. For now, these are arguments are unused, but as we add
RSS support, we will want to use hashes extracted from mbufs, rather than
manually calculated hashes of header fields, due to the expensive of the
software version of Toeplitz (and similar hashes).
Add notes that it would be nice to be able to pass mbufs into lookup
routines in pf(4), optimising firewall lookup in the same way, but the
code structure there doesn't facilitate that currently.
(In principle there is no reason this couldn't be MFCed -- the change
extends rather than modifies the KBI. However, it won't be useful without
other previous possibly less MFCable changes.)
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
to not only compile bu load as well for testing with IPv6-only kernels.
For the moment we ignore the csum change in pf_ioctl.c given the
pending update to pf45.
Reported by: dru
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 20 days
- The existing ipi_lock continues to protect the global inpcb list and
inpcb counter. This lock is now relegated to a small number of
allocation and free operations, and occasional operations that walk
all connections (including, awkwardly, certain UDP multicast receive
operations -- something to revisit).
- A new ipi_hash_lock protects the two inpcbinfo hash tables for
looking up connections and bound sockets, manipulated using new
INP_HASH_*() macros. This lock, combined with inpcb locks, protects
the 4-tuple address space.
Unlike the current ipi_lock, ipi_hash_lock follows the individual inpcb
connection locks, so may be acquired while manipulating a connection on
which a lock is already held, avoiding the need to acquire the inpcbinfo
lock preemptively when a binding change might later be required. As a
result, however, lookup operations necessarily go through a reference
acquire while holding the lookup lock, later acquiring an inpcb lock --
if required.
A new function in_pcblookup() looks up connections, and accepts flags
indicating how to return the inpcb. Due to lock order changes, callers
no longer need acquire locks before performing a lookup: the lookup
routine will acquire the ipi_hash_lock as needed. In the future, it will
also be able to use alternative lookup and locking strategies
transparently to callers, such as pcbgroup lookup. New lookup flags are,
supplementing the existing INPLOOKUP_WILDCARD flag:
INPLOOKUP_RLOCKPCB - Acquire a read lock on the returned inpcb
INPLOOKUP_WLOCKPCB - Acquire a write lock on the returned inpcb
Callers must pass exactly one of these flags (for the time being).
Some notes:
- All protocols are updated to work within the new regime; especially,
TCP, UDPv4, and UDPv6. pcbinfo ipi_lock acquisitions are largely
eliminated, and global hash lock hold times are dramatically reduced
compared to previous locking.
- The TCP syncache still relies on the pcbinfo lock, something that we
may want to revisit.
- Support for reverting to the FreeBSD 7.x locking strategy in TCP input
is no longer available -- hash lookup locks are now held only very
briefly during inpcb lookup, rather than for potentially extended
periods. However, the pcbinfo ipi_lock will still be acquired if a
connection state might change such that a connection is added or
removed.
- Raw IP sockets continue to use the pcbinfo ipi_lock for protection,
due to maintaining their own hash tables.
- The interface in6_pcblookup_hash_locked() is maintained, which allows
callers to acquire hash locks and perform one or more lookups atomically
with 4-tuple allocation: this is required only for TCPv6, as there is no
in6_pcbconnect_setup(), which there should be.
- UDPv6 locking remains significantly more conservative than UDPv4
locking, which relates to source address selection. This needs
attention, as it likely significantly reduces parallelism in this code
for multithreaded socket use (such as in BIND).
- In the UDPv4 and UDPv6 multicast cases, we need to revisit locking
somewhat, as they relied on ipi_lock to stablise 4-tuple matches, which
is no longer sufficient. A second check once the inpcb lock is held
should do the trick, keeping the general case from requiring the inpcb
lock for every inpcb visited.
- This work reminds us that we need to revisit locking of the v4/v6 flags,
which may be accessed lock-free both before and after this change.
- Right now, a single lock name is used for the pcbhash lock -- this is
undesirable, and probably another argument is required to take care of
this (or a char array name field in the pcbinfo?).
This is not an MFC candidate for 8.x due to its impact on lookup and
locking semantics. It's possible some of these issues could be worked
around with compatibility wrappers, if necessary.
Reviewed by: bz
Sponsored by: Juniper Networks, Inc.
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
o) Add 'octm', a trivial driver for the 10/100 management ports found on some
Octeon systems.
o) Make the Simple Executive's management port helper routines compile on
FreeBSD (namely by not doing math on void pointers.)
o) Add a cvmx_mgmt_port_sendm routine to the Simple Executive to send an mbuf
so there is only one copy in the transmit path, rather than having to first
copy the mbuf to an intermediate buffer and then copy that to the Simple
Executive's transmit ring.
o) Properly work out MII addresses of management ports on the Lanner MR-730.
XXX The MR-730 also needs some patches to the MII read/write routines, but
this is sufficient for now. Media detection will be fixed in the future
when I can spend more time reading the vendor-supplied patches.
facilities as well as support for the Octeon 2 family of SoCs.
XXX Note that with our antediluvian assembler, we can't support some Octeon 2
instructions and fall back to using the old ones instead.
o) Fix enumeration of PHY addresses on the MR-955.
o) Parse link state for the MR-730 using the Broadcom PHY support in the SDK.
It's not clear that this is entirely-correct, but it seems to work. Since
this board uses a BCM5482S, this may mean that we work correctly for copper
but not SFI, which is untested.
the miibus attached to octe interfaces.
o) Add an SMI/MDIO interface to the MV88E61XX and use it for the switch PHY on
the Lanner MR-320. An actual driver for the switch PHY will come later.
Note that for now it intercepts and fakes MII_BMSR reads to prevent the
miibus from talking to anything but the switch itself.
seem to be problems both with the on-board Ethernet interfaces and the em(4)
interfaces on PCI under FreeBSD.
Thanks to Lanner for providing access to hardware.
for interfaces with TSO enabled, otherwise one would see an extra
ICMP unreach, frag needed pre matching packet on lo0.
This syncs pf code to ip_output.c r162084.
PR: kern/144311
Submitted by: yongari via mlaier
Reviewed by: eri
Tested by: kib
MFC after: 8 days
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
Executive is a library that can be used by standalone applications and kernels
to abstract access to Octeon SoC and board-specific hardware and facilities.
The FreeBSD port to Octeon will be updated to use this where possible.
"Whitspace" churn after the VIMAGE/VNET whirls.
Remove the need for some "init" functions within the network
stack, like pim6_init(), icmp_init() or significantly shorten
others like ip6_init() and nd6_init(), using static initialization
again where possible and formerly missed.
Move (most) variables back to the place they used to be before the
container structs and VIMAGE_GLOABLS (before r185088) and try to
reduce the diff to stable/7 and earlier as good as possible,
to help out-of-tree consumers to update from 6.x or 7.x to 8 or 9.
This also removes some header file pollution for putatively
static global variables.
Revert VIMAGE specific changes in ipfilter::ip_auth.c, that are
no longer needed.
Reviewed by: jhb
Discussed with: rwatson
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 6 days
it from machine/in_cksum.h. This definition prevents us from using
hand-tuned assembler versions of in_cksum.
# this fixes the modules build on arm for ipfilter.
This is a split merge because of non-uniform licensing of the DTC package
contents and the way these components will be used in the FreeBSD environment.
The original DTC package is composed of the following two major pieces:
1. sys/contrib/libfdt (BSD [dual] license)
2. contrib/dtc (GPLv2)
The libfdt component is going to be shared in all aspects of the environment:
- /boot/loader
- kernel
- dtc (the device tree compiler proper, userspace tool)
TRENDnet TEW-504UB/EU) idProduct didn't be decreased after loading the
firmware.
Pointed by: Steven Friedrich <freebsd at insightbb.com>
Reviewed by: sam
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
Server Return mode, where not all packets would be visible to the load
balancer or gateway.
This commit should be reverted when we merge future pf versions. The
benefit it would provide is that this version does not break any existing
public interface and thus won't be a problem if we want to MFC it to
earlier FreeBSD releases.
Discussed with: mlaier
Obtained from: OpenBSD
Sponsored by: iXsystems, Inc.
MFC after: 1 month
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
several critical bugs, including race conditions and lock order issues:
Replace the single rwlock, ifnet_lock, with two locks, an rwlock and an
sxlock. Either can be held to stablize the lists and indexes, but both
are required to write. This allows the list to be held stable in both
network interrupt contexts and sleepable user threads across sleeping
memory allocations or device driver interactions. As before, writes to
the interface list must occur from sleepable contexts.
Reviewed by: bz, julian
MFC after: 3 days
restart the scan after acquiring the lock the hard way. Otherwise we might
end up with a dead reference.
Reported by: pfsense
Reviewed by: eri
Initial patch by: eri
Tested by: pfsense
Approved by: re (kib)
all pertinent statatistics for the subsystem. These structures are
sometimes "borrowed" by kernel modules that require a place to store
statistics for similar events.
Add KPI accessor functions for statistics structures referenced by kernel
modules so that they no longer encode certain specifics of how the data
structures are named and stored. This change is intended to make it
easier to move to per-CPU network stats following 8.0-RELEASE.
The following modules are affected by this change:
if_bridge
if_cxgb
if_gif
ip_mroute
ipdivert
pf
In practice, most of these statistics consumers should, in fact, maintain
their own statistics data structures rather than borrowing structures
from the base network stack. However, that change is too agressive for
this point in the release cycle.
Reviewed by: bz
Approved by: re (kib)
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
o new tx ack queue (not used right now)
o proxy-sta related changes (no proxy sta in driver)
o explicit dwds ena/dis (needed only with proxy sta)
o cleanup BA policy handling
o new ampdu aggressive mode support
o CFEnd use now controllable
Approved by: re (kensmith)
rather than pointers, requiring callers to properly dispose of those
references. The following routines now return references:
ifaddr_byindex
ifa_ifwithaddr
ifa_ifwithbroadaddr
ifa_ifwithdstaddr
ifa_ifwithnet
ifaof_ifpforaddr
ifa_ifwithroute
ifa_ifwithroute_fib
rt_getifa
rt_getifa_fib
IFP_TO_IA
ip_rtaddr
in6_ifawithifp
in6ifa_ifpforlinklocal
in6ifa_ifpwithaddr
in6_ifadd
carp_iamatch6
ip6_getdstifaddr
Remove unused macro which didn't have required referencing:
IFP_TO_IA6
This closes many small races in which changes to interface
or address lists while an ifaddr was in use could lead to use of freed
memory (etc). In a few cases, add missing if_addr_list locking
required to safely acquire references.
Because of a lack of deep copying support, we accept a race in which
an in6_ifaddr pointed to by mbuf tags and extracted with
ip6_getdstifaddr() doesn't hold a reference while in transmit. Once
we have mbuf tag deep copy support, this can be fixed.
Reviewed by: bz
Obtained from: Apple, Inc. (portions)
MFC after: 6 weeks (portions)
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.
Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.
- Define ACPI_USE_DO_WHILE_0 to add do while(0) around return_*() macros.
- Define __cdecl only for user land. It will never be used in kernel.
- Remove __cli() and __sti(). They were deprecated long ago.
and used in a large number of files, but also because an increasing number
of incorrect uses of MAC calls were sneaking in due to copy-and-paste of
MAC-aware code without the associated opt_mac.h include.
Discussed with: pjd
by creating a child jail, which is visible to that jail and to any
parent jails. Child jails may be restricted more than their parents,
but never less. Jail names reflect this hierarchy, being MIB-style
dot-separated strings.
Every thread now points to a jail, the default being prison0, which
contains information about the physical system. Prison0's root
directory is the same as rootvnode; its hostname is the same as the
global hostname, and its securelevel replaces the global securelevel.
Note that the variable "securelevel" has actually gone away, which
should not cause any problems for code that properly uses
securelevel_gt() and securelevel_ge().
Some jail-related permissions that were kept in global variables and
set via sysctls are now per-jail settings. The sysctls still exist for
backward compatibility, used only by the now-deprecated jail(2) system
call.
Approved by: bz (mentor)
made LINT happy this does the proper looping over all vnets as we are
only called `globally' and not once per vnet instance.
Reported by: zec [1]
Missed by: bz [1] in r192264
Reviewed by: zec
rearrange / replace / adjust several INIT_VNET_* initializer
macros, all of which currently resolve to whitespace.
Reviewed by: bz (an older version of the patch)
Approved by: julian (mentor)
macros: ICMPSTAT_ADD(), ICMPSTAT_INC(), ICMP6STAT_ADD(), and
ICMP6STAT_INC(), rather than directly manipulating the fields
of these structures across the kernel. This will make it
easier to change the implementation of these statistics,
such as using per-CPU versions of the data structures.
In on case, icmp6stat members are manipulated indirectly, by
icmp6_errcount(), and this will require further work to fix
for per-CPU stats.
MFC after: 3 days
and UDPSTAT_INC(), rather than directly manipulating the fields
across the kernel. This will make it easier to change the
implementation of these statistics, such as using per-CPU versions
of the data structures.
MFC after: 3 days
