as kernel drivers and their dependency onto mmc(4); this allows for
incrementing the mmc(4) module version but also for entire omission
of these bridge declarations for mmccam(4) in a single place, i. e.
in dev/mmc/bridge.h.
comments, marking unused parameters as such, style(9), whitespace,
etc.
o In the mmc(4) bridges and sdhci(4) (bus) front-ends:
- Remove redundant assignments of the default bus_generic_print_child
device method (I've whipped these out of the tree as part of r227843
once, but they keep coming back ...),
- use DEVMETHOD_END,
- use NULL instead of 0 for pointers.
o Trim/adjust includes.
RPi3 cpufreq is more like that on RPi2. Setting arm frequency
above min (say, "sysctl hw.cpufreq.arm_freq=600000001") turns on
turbo mode, and the firmware automatically raises voltage, sets
frequency to max 1200MHz, and throttle when overheat, etc.
Swap if/else parts and use SOC_BCM2835 def so RPi3 can share the
same cpufreq logic as RPi2, instead of falling to that for RPi.
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9640
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
This adds clocks support for the aw_ccung on the A31 SoC.
Newer DTS files require this.
All the clocks except two CSI are defined and exported on the clock domain.
The PLL_DDR clock have an update bit which need to be set after changing
the value, add the possibility to define one for NKMP clocks.
This allow us to add the missing clocks.
We now have the full list of clocks created under the clock domain.
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Since Linux 4.9-4.10 DTS doesn't have clocks under /clocks but only a ccu node.
Currently only H3 is supported with almost the same state as HEAD.
(video pll aren't supported for now but we don't support video).
This driver and clocks will also be used for other SoC (A64, A31, H5, H2 etc ...)
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D9517
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
if the fdt data doesn't provide a gpio pin for reading the write protect
switch and also doesn't contain a "wp-disable" property.
In r311735 the long-bitrotted code in this driver for using the non-
standard fdt "mmchs-wp-gpio-pin" property was replaced with new common
support code for handling write-protect and card-detect gpio pins. The
old code never found a property with that name, and the logic was to
assume that no gpio pin meant that the card was not write protected.
The new common code behaves differently. If there is no fdt data saying
what to do about sensing write protect, the value in the standard SDHCI
PRESENT_STATE register is used. On this hardware, if there is no signal
for write protect muxed into the sd controller then that bit in the
register indicates write protect.
The real problem here is the fdt data, which should contain "wp-disable"
properties for eMMC and micro-sd slots where write protect is not even
an option in the hardware, but we are not in control of that data, it
comes from linux. So we have to make the same flawed assumption in our
driver that the corresponding linux driver has: no info means no protect.
Reported by: several users on the arm@ list
Pointy hat: me, for not testing enough before committing r311735
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
On arm64 use atomics. Then, both arm and arm64 do not need a critical
section around update. Replace all cpus loop by CPU_FOREACH().
This brings arm and arm64 counter(9) implementation closer to current
amd64, but being more RISC-y, arm* version cannot avoid atomics.
Reported by: Alexandre Martins <alexandre.martins@stormshield.eu>
Reviewed by: andrew
Tested by: Alexandre Martins, andrew
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
identify_arm_cpu() in sys/arm/arm/identcpu-v4.c incorrectly uses a
u_int8_t variable to store the result of cpu_get_control().
It should really use a u_int variable, the same way as done for cpu_ident()
in the same function, as both cpuid and control registers are 32-bit..
This issue causes users of identcpu-v4 to incorrectly report things such as
icache status (bit 12 in cpu control register) and basically anything
defined in bits above bit 7 :-)
Reviewed by: manu
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D9460
The types are for the byte offset and page index in vm object. They
are similar to off_t, which is defined as 64bit MI integer. Using MI
definitions will allow to provide consistent MD values of vm
object-related maximum sizes.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
Historically AM335x LCDC driver used non-standard "hdmi" property to
refer to HDMI framer. There is no such thing in upstream DTS, so to
handle both cases fallback to bindings described in
bindings/media/video-interfaces.txt in Linux documentation.
We still make some assumptions that are not universally true: we
assume that if remote endpoint is available it's going to be HDMI
framer. Which is true for AM335x-based devices currently supported
but may be not true for some custom hardware.
MFC after: 1 week
register, in addition to configuring it as input with the pinmux driver.
There was a control register bit commented as "no desc in datasheet". A
later revision of the manual reveals the bit to be an input/output control
for the timer pin. In addition to configuring capture or pulse mode, you
apparently have to separately configure the pin direction in the timer
control register.
Before this change, the timer block was apparently driving a signal onto a
pad configured by pinmux as input. Capture mode still accidentally worked
for me during testing because I was using a very strong signal source that
just out-muscled the weaker drive from the misconfigured pin.
Commit r312747 ("Setup decoding windows for ARMADA38X") resulted
in build failing for Marvell platforms, which don't have AHCI controller.
This patch provides a fix by adding dummy functions for such cases.
On the occasion rename register dump routine to decode_win_ahci_dump,
in order to avoid confusion.
Submitted by: Marcin Wojtas <mw@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
- Replace pcpu_find(curcpu) with get_pcpu(), which is much
more direct.
- Remove armv4 pcpu fields which I added in r286296 but never
needed to use.
- armv6 pc_qmap_addr was leftover from the old armv6 pmap
implementation. Rename it and put it to use in the new one.
Noted by: skra
Reviewed by: skra
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9312
This file provides support for AHCI mode on Armada38x
and adds new optional AHCI device to arm/mv/files.mv.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9222
It is necesarry to open memory windows on internal bus for
AHCI driver to work correctly.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9220
Configure decoding windows only for devices with
enabled nodes in FDT.
Submitted by: Konrad Adamczyk <ka@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: zbb
Differential revision: https://reviews.freebsd.org/D9219
* Currently supports only Armada38X family but other Marvell SoC's
can be added if needed.
* Provides temperature is C deg.
* To print the temperature one can use:
sysctl dev.armada_thermal.0.temperature
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D9217
