added/removed interfaces in a more consistent manner and reloading
the configuration file.
- Add initial support for control socket. RA information in the
daemon can be obtained by rtadvctl(8) instead of SIGUSR1 in a similar
manner to ifconfig(8). The information dump has been removed in favor of it.
(reload the configuration file)
# rtadvctl reload
(show RA messages being sent on each interfaces)
# rtadvctl show
em0: flags=<UP,CONFIGURED,PERSIST> status=<RA_SEND> mtu 1280
DefaultLifetime: 30m
MinAdvInterval/MaxAdvInterval: 3m20s/3m20s
AdvLinkMTU: <none>, Flags: O, Preference: medium
ReachableTime: 0s, RetransTimer: 0s, CurHopLimit: 64
AdvIfPrefixes: yes
(show RA messages being sent only on em0)
# rtadvctl show em0
(rtadvctl -v show provides additional information)
# rtadvctl -v show em0
em0: flags=<UP,CONFIGURED,PERSIST> status=<RA_SEND> mtu 1280
DefaultLifetime: 30m
MinAdvInterval/MaxAdvInterval: 3m20s/3m20s
AdvLinkMTU: <none>, Flags: O, Preference: medium
ReachableTime: 0s, RetransTimer: 0s, CurHopLimit: 64
AdvIfPrefixes: yes
Prefixes (1):
2001:db8:1::/64 (CONFIG, vltime=30d, pltime=7d, flags=LA)
RDNSS entries:
2001:db8:1::128 (ltime=2m40s)
(stop rtadvd)
# rtadvctl shutdown
A remaining issue when reloading the configuration file is that
during that period rtadvd cannot communicate with rtadvctl due to some
additional RA sending for graceful shutdown. This will be fixed later.
Options for DNS Configuration) into rtadvd(8) and rtsold(8). DNS
information received by rtsold(8) will go to resolv.conf(5) by
resolvconf(8) script. This is based on work by J.R. Oldroyd (kern/156259)
but revised extensively[1].
- rtadvd(8) now supports "noifprefix" to disable gathering on-link prefixes
from interfaces when no "addr" is specified[2]. An entry in rtadvd.conf
with "noifprefix" + no "addr" generates an RA message with no prefix
information option.
- rtadvd(8) now supports RTM_IFANNOUNCE message to fix crashes when an
interface is added or removed.
- Correct bogus ND_OPT_ROUTE_INFO value to one in RFC 4191.
Reviewed by: bz[1]
PR: kern/156259 [1]
PR: bin/152458 [2]
- deprecate routes#N, as it is hard to keep consistency with
rtprefixN. accept any number of "rtprefix", "rtrefix0",
..., "rtprefix99".
- deprecate "addrs#N", as it is difficult for users to keep
consistency with "addrN".
accept 100 prefix info in maximum - like "addr", "addr0"
... "addr99". WARNS=2 clean on netbsd.
old configuration file should work just fine.
behavior change:
previously, we rejected "addrN" if there's "addr", and we rejected
"addr" if there is "addrN". now we accept both without problem.
- when an advertised prefix configured from the kernel has been added
or invalidated, notice the change in a short delay.
- when invalidating a prefix, do not bark even if there is
inconsistency about prefix lifetimes.
- wrap more specific route info code into ROUTEINFO.
Obtained from: KAME
MFC after: 1 week
was removed from the kernel;
Advertise the prefix with zero lifetimes rather than to remove the prefix
from the prefix list to be advertised.
This will help renumber a receiving host by deprecating the address
derived from the old prefix.
Obtained from: KAME
MFC after: 2 weeks
Avoid using parenthesis enclosure macros (.Pq and .Po/.Pc) with plain text.
Not only this slows down the mdoc(7) processing significantly, but it also
has an undesired (in this case) effect of disabling hyphenation within the
entire enclosed block.
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
