This was submitted by Rogiel Sulzbach (thank you!) but has a few last-minute
changes by me, mostly where the code interfaces to my still-utterly-deficient
imx6_ccm clocks implementation. So blame me for any mistakes.
Submitted by: Rogiel Sulzbach <rogiel@rogiel.com>
Differential Revision: https://reviews.freebsd.org/D11177
as taking a register number, and that would get multiplied by 4 to make
a register address. But the header file that consumers have to reference
this stuff publishes register addresses, not numbers. So now everything
works in terms of register addresses.
Note that the HDMI init code was writing into the wrong register before
this change. Apparently whatever it wrote to was harmless, and apparently
HDMI was working because uboot had set up the right bits.
It turns out that this is more than a power optization. The OTG port
won't work on boards that have this property unless this setting is honored.
Also ensure that the usb phy device attaches before ehci.
This allows multiple instances of SoCs that use the pl310 driver to be
built within the same kernel:
* Add access to the platform_t object from outside platform.c
* Use this with the pl310 driver
There is a new platform_pl310 interface to replace the existing code. SoCs
need to implement the init method, and if they have special requirements to
write to the two registers we care about will also need to implement the
write_ctrl and write_debug methods.
Differential Revision: https://reviews.freebsd.org/D11546
This driver is standard rather than optional because it can always provide
time after a reboot, but it will only provide time after a power cycle if
battery power is supplied to the chip's SNVS power domain.
When a pin is set for input the value in the DR will be the same as the PSR.
When a pin is set for output the value in the DR is the value output to the
pad, and the value in the PSR is the actual electrical level sensed on the
pad, and they can be different if the pad is configured for open-drain mode
and some other entity on the board is driving the line low.
timecounter instead of the GPT timer, freeing up the more flexible GPT
hardware for other uses. The EPIT driver is a standard (always in the
kernel) driver, and the existing GPT driver is now optional and included
only if you ask for device imx_gpt.
imx6 based on a single cortex-a7 core. Other changes to imx6 drivers
and support code are needed to fully support the imx6ul.
Also fix an indentation glitch committed in the prior change.
driver for imx6. Some newer dts source puts the GIC node at the root
instead of under /soc, so look in both places. Also, sometimes the GIC
node doesn't list itself as its own interrupt-parent, allow that too.
At this point, INTRNG is not going away (the option may go away, but the
code is not), so we no longer need code to support workarounds that handled
the lack of INTRNG functionality.
calculated at runtime based on how long it takes to set up an event in
hardware. This fixes the intermittant 1-minute hang at boot on imx5
systems, and also the occasional oversleeping while running. It doesn't
affect imx6 systems, which use different hardware for eventtimers.
It turns out that it usually takes about 30 timer ticks to set up the timer
compare register, and the old hard-coded minimum period was 10 ticks. On
the rare occasions when a timeout event that short was set up, we'd miss
the event and have to wait about 64 seconds for counter rollover before
the compare interrupt would fire.
Instead of just hardcoding a new bigger value, the code now measures the
time it takes to do the register read/write sequence to set up the compare
register, scales it up by 1.5x to be safe, and calculates the minimum event
period from the result. In the real world, the minimum period works out to
about 750 nanoseconds on imx5 hardware.
It turns out to be surprisingly expensive to access the gpt hardware (on the
order of 150ns per read/write). To cut down on the overhead of setting up
each eventtimer event, eliminate read-modify-write sequences to manage the
compare interrupt enable, by keeping a shadow copy of the hardware register
and only writing to the hardware when the enable bits really change.
cleanups enabled by that:
- The only thing left in imx_gptvar.h was the softc, which IMO never
should have been in there at all. Move it into the driver, and
delete the header file.
- Remove several unneeded #includes from the driver.
- Change imx_gpt_softc from global to static (it's used by DELAY()), and
don't redundantly static-initialize it to NULL.
supply the addresses for the DPLL register blocks) by hard-coding the
addresses in the driver source code. Yes, this is just as bad an idea as
it sounds, but we have no choice.
In the early days of using fdt data, when we were making up our own data
for each board, we defined 4 sets of memory mapped registers in the data.
The vendor-supplied data only provides the address of the CCM register
block, but not the 3 DPLL blocks. The linux driver has the DPLL physical
addresses (which differ by SOC type) hard-coded in the driver, and we
have no choice but to do the same thing if we want to run with the vendor-
supplied fdt data.
So now we use bus_space_map() to make the DPLL blocks accessible, choosing
the set of fixed addresses to map based on the soc id.
be migrated to this and will allow the removal of this option.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D9907
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
- Place const modifiers where required
- Make sure sdma device is attahched before consumers like SSI
Reviewed by: br
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8874
file and add a generic DT binding that takes advantage of the extres
framework for setting up clocks.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D8826
As cs is stored in a uint32_t, use the last bit to store the
active high flag as it's unlikely that we will have that much CS.
Reviewed by: loos
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8614
Replace them with a default handler that returns devmap_lastaddr.
Reviewed by: mmel
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8806
Up until r295436 GPT timer in i.MX6 Dual dts used the same compatiblity
string as i.MX6 Quad. After the sync up with Linux in r295436, GPT timer
stopped getting attached on the i.MX6 Dual
MFC after: 3 days
