Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Throw away the result of the peer SPAD read. The peer will write our
local SPAD and we need to keep the locally read SPAD value to check if
the remote side is up.
Sponsored by: EMC / Isilon Storage Division
Add module parameters for the addresses to be used in B2B topology.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
We skip actually bringing up Rootport/Transparent configurations, so
most of this doesn't apply. Original Linux commit log:
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
It is just a trivial wrapper around ntb_mw_set_trans().
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The failure path for allocating rx grant refs should not try to free tx
grant refs because tx grant refs were allocated after that. Also fix the
error path for xen_net_read_mac.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3891
Sponsored by: Citrix Systems R&D
This is redundant because ether_ifattach will set that field.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3918
Sponsored by: Citrix Systems R&D
We're way beyond FreeBSD 7 at this point.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3892
Sponsored by: Citrix Systems R&D
Multiqueue feature will make the number of queues dynamic, so XN_LOCK_INIT
won't be that useful. Remove the macro and call mtx_init directly.
XN_LOCK_DESTROY is just dead code.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3890
Sponsored by: Citrix Systems R&D
Rename it with netfront_ prefix and purge a bunch of unused fields.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3889
Sponsored by: Citrix Systems R&D
Currently neither Linux nor FreeBSD netback supports page flipping. NetBSD
still supports that. It is not sure how many people actually use page
flipping, but page flipping is supposed to be slower than copying nowadays.
It will also shatter frontend / backend address space.
Overall this feature is more of a burden than a benefit.
Submitted by: Wei Liu <wei.liu2@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3888
Sponsored by: Citrix Systems R&D
- Define the kref structure identical to the one found in Linux.
- Update clients referring inside the kref structure.
- Implement kref_sub() for FreeBSD.
Reviewed by: np @
Sponsored by: Mellanox Technologies
* Use the correct malloc type for node allocation - M_80211_NODE - so
the default node free method in net80211 will work correctly.
* Fix otus_node_alloc() to suit FreeBSD's net80211.
* .. and actually call otus_node_alloc() so there's space for the
per-node tx statistics. Otherwise, well, it will be scribbling over
random memory.
Tested:
* AR9170, STA mode
The monitor mode stuff is from the openbsd driver, but it doesn't
100% work. It doesn't seem to get all frames for all BSSes.
However, it's enough to at start debugging things. That 0xffffffff
write is /I think/ the RX filter, but I am still not 100% sure about
it all.
Then, whilst here, use the lowest rate for EAPOL frames. This is just
generally a good thing to do.
This commit adds support for MDIO present in the ThunderX SoC.
From the FDT point of view it is compatible with "octeon-3860-mdio"
however only C22 mode is used.
The code also implements lmac_if interface functions.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
- The driver consists of three main componens: PF, VF, BGX
- Requires appropriate entries in DTS and MDIO driver
- Supports only FDT configuration
- Multiple Tx queues and single Rx queue supported
- No RSS, HW checksum and TSO support
- No more than 8 queues per-IF (only one Queue Set per IF)
- HW statistics enabled
- Works in all available MAC modes (1,10,20,40G)
- Style converted to BSD according to style(9)
- The code brings lmac_if interface used by the BGX driver to
update its logical MACs state.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
This import brings following components of the Linux driver:
- Thunder BGX (programmable MAC)
- Physical Function driver
- Virtual Function driver
- Headers
Revision: 1.0
Obtained from: Cavium
License information: Cavium provided these files under BSD license
This is the last e26a5843 patch. The general thrust of the rewrite was
to move more responsibility for Memory Window and Doorbell interrupt
management from the ntb_hw driver to if_ntb.
A number of APIs have been added, removed, or replaced. The old
DB callback mechanism has been excised. Instead, callers (if_ntb) are
responsible for configuring MWs and handling their interrupts more
directly.
This adds a tunable, hw.ntb.max_mw_size, allowing users to limit the
size of memory windows used by if_ntb (identical to the Linux modparam
of the same name).
Despite attempts to keep mechanical name changes to separate commits,
some have snuck in here. At least the driver should be much more
similar to the latest Linux one now -- making porting fixes easier.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change. Part of the huge rewrite (e26a5843).
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Move all Xeon secondary register setup to the setup_b2b_mw routine. We
use subroutines to make it a bit less wordy than the Linux version.
Adds a new tunable, 'hw.ntb.b2b_mw_share'. By default, it is off
(zero). If both sides enable it (any non-zero value), the NTB driver
attempts to use only half of a memory window for remote register MMIO
access.
This is still part of the large Linux rewrite (e26a5843).
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This Linux commit was more or less a rewrite. Unfortunately, the commit
log does not give a lot of context for the rewrite. I have tried to
faithfully follow the changes made upstream, including matching function
names where possible, while churning the FreeBSD driver as little as
possible.
This is the bulk of the rewrite. There are two groups of changes to
follow in separate commits: fleshing out the rest of the changes to
xeon_setup_b2b_mw(), and some changes to if_ntb.
Yes, this is a big patch (3 files changed, 416 insertions(+), 237
deletions(-)), but the Linux patch was 13 files changed, 2,589
additions(+) and 2,195 deletions(-).
Original Linux commit log:
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Some interrupt-related function names changed to match Linux.
No functional change. Still part of the huge e26a5843 rewrite in Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change.
Still part of the huge e26a5843 rewrite. I'm trying to make it less of
a complete rewrite in the FreeBSD version of the driver. Still, it
helps if our names match Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
On the Haswell platform, a split BAR option to allow creation of 2 32bit
BARs (4 and 5) from the 64bit BAR 4. Adding support for this new option.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This is a follow-up to r289208: "Xeon Errata Workaround."
Add logic to support a variable number of memory windows and doorbell
callbacks. This was added to the Linux driver in the "Xeon Errata
Workaround" commit, but I skipped it because it didn't look neccessary
at the time. It is needed for future Haswell split-BAR support, so
bring it in now.
A new tunable was added for if_ntb, 'hw.ntb.max_num_clients'. By
default, it is set to zero -- infer the number of clients from the
number of memory windows available from the hardware. Any other
positive value can specify a different number of clients, limited by the
number of doorbell callbacks available (4 under MSI-X, or 15 (Xeon) or
34 (SoC) under legacy INTx).
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This patch adds support for the BCM57765[2] card reader function included in
Broadcom's BCM57766 ethernet/sd3.0 controller. This controller is commonly
found in laptops and Apple hardware (MBP, iMac, etc).
The BCM57765 chipset is almost fully compatible with the SD3.0 spec, but
does not support deriving a frequency below 781KHz from its default base
clock via the standard SD3.0-configured 10-bit clock divisor.
If such a divisor is set, card identification (which requires a 400KHz
clock frequency) will time out[1].
As a work-around, I've made use of an undocumented device-specific clock
control register to switch the controller to a 63MHz clock source when
targeting clock speeds below 781KHz; the clock source is likewise switched
back to the 200MHz clock when targeting speeds greater than 781KHz.
Additionally, this patch fixes a small sdhci_pci bug; the
sdhci_pci_softc->quirks flag was not copied to the sdhci_slot, resulting in
`quirk` behavior not being applied by sdhci.c.
[1] A number of Linux/FreeBSD users have noted that bringing up the chipsets'
associated ethernet interface will allow SD cards to enumerate (slowly).
This is a controller implementation side-effect triggered by the ethernet
driver's reading of the hardware statistics registers.
[2] This may also fix card detection when using the BCM57785 chipset, but I
don't have access to the BCM57785 chipset and can't verify.
I actually snagged some BCM57785 hardware recently (2012 Retina MacBook Pro)
and can confirm that this also fixes card enumeration with the BCM57785
chipset; with the patch, I can boot off of the internal sdcard reader.
PR: kern/203385
Submitted by: Landon Fuller <landon@landonf.org>
Pull out read of PPD and platform detection logic to new functions,
ntb_detect_xeon(), ntb_detect_soc(). No functional change -- mostly
this is just shuffling the code to more closely match the Linux driver.
Linux commit log:
To simplify some of the platform detection code. Move the platform
detection to a function to be called earlier.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The doorbell registers (and associated mask) are 16-bit on Xeon but
64-bit on SoC. Abstract IO access to doorbell registers with
'db_ioread' and 'db_iowrite' (names and idea borrowed from the dual
BSD/GPL Linux driver).
Sponsored by: EMC / Isilon Storage Division
Original Linux commit log:
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Remap MSI-X messages over available slots rather than falling back to
legacy INTx when fewer MSI-X slots are available than were requested.
N.B. the Linux driver does *not* do this.
To aid in testing, a tunable 'hw.ntb.force_remap_mode' has been added.
It defaults to off (0). When the tunable is enabled and sufficient
slots were available, the driver restricts the number of slots by one
and remaps the MSI-X messages over the remaining slots.
In case this is actually not okay (as I don't yet have access to this
hardware to test), a tunable 'hw.ntb.prefer_intx_to_remap' has been
added. It defaults to off (0). When the tunable is enabled and fewer
slots are available than requested, fall back to legacy INTx mode rather
than attempting to remap MSI-X messages.
Suggested by: jhb
Reviewed by: jhb (earlier version)
Sponsored by: EMC / Isilon Storage Division
Consumers that registered on this bit would never see a callback and it
is likely a mistake.
This does not affect if_ntb, which limits itself to a single doorbell
callback.
The names don't line up 100% with Linux. Our routines are named
ntb_setup_interrupts, ntb_setup_xeon_msix, ntb_setup_soc_msix, and
ntb_setup_legacy_interrupt. Linux SNB = FreeBSD Xeon; Linux BWD =
FreeBSD SOC. Original Linux commit log:
This is an cleanup effort to make ntb_setup_msix() more readable - use
ntb_setup_bwd_msix() to init MSI-Xs on BWD hardware and
ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the way it should
has been done - looping pci_enable_msix() until success or failure.
Authored by: Alexander Gordeev
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Provide a better event interface between the client and transport.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
according to the Cortex-A8 TRM r3p2 section 3.2.49.
The A8 list differs from the "ARM-v7 common" list, given the A8
was an earlier model.
There is still more work to be done for other Cortex-Ax version as
andrew points out, but I am just trying to fix A8 for now for teaching.
MFC after: 2 weeks
Sponsored by: DARPA/AFRL
Obtained from: Cambridge/L41
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3876
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs. Previously, Snoop was only enabled from Secondary to Primary
side. This can have a performance improvement on some workloads.
Also, make the code more obvious about how the link is being enabled.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Add a comment describing the necessary ordering of modifications to the
NTB Limit and Base registers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active. This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated. To correct this, shutdown the qp's prior to bringing
the transport link down. Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt. Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue. To get around
the issue, shrink the number of available doorbell bits by 1. The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit. Since this would no longer work, the driver must now
explicitly reference that bit.
This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
NTB-RP is not a supported configuration on BWD hardware. Remove the
code attempting to set it up.
Authored by: Jon Mason
Obtained from: Linux (dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This commit does not actually add NTB-RP support. Mostly it serves to
shuffle code around to match the Linux driver. Original Linux commit
log follows:
Add support for Non-Transparent Bridge connected to a PCI-E Root Port on
the remote system (also known as NTB-RP mode). This allows for a NTB
enabled system to be connected to a non-NTB enabled system/slot.
Modifications to the registers and BARs/MWs on the Secondary side by the
remote system are reflected into registers on the Primary side for the
local system. Similarly, modifications of registers and BARs/MWs on
Primary side by the local system are reflected into registers on the
Secondary side for the Remote System. This allows communication between
the 2 sides via these registers and BARs/MWs.
Note: there is not a fix for the Xeon Errata (that was already worked
around in NTB-B2B mode) for NTB-RP mode. Due to this limitation, NTB-RP
will not work on the Secondary side with the Xeon Errata workaround
enabled. To get around this, disable the workaround via the
xeon_errata_workaround=0 modparm. However, this can cause the hang
described in the errata.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Many variable names in the NTB driver refer to the primary or secondary
side. However, these variables will be used to access the reverse case
when in NTB-RP mode. Make these names more generic in anticipation of
NTB-RP support.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The BWD NTB device will drop the link if an error is encountered on the
point-to-point PCI bridge. The link will stay down until all errors are
cleared and the link is re-established. On link down, check to see if
the error is detected, if so do the necessary housekeeping to try and
recover from the error and reestablish the link.
There is a potential race between the 2 NTB devices recovering at the
same time. If the times are synchronized, the link will not recover and
the driver will be stuck in this loop forever. Add a random interval to
the recovery time to prevent this race.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
There is a Xeon hardware errata related to writes to SDOORBELL or B2BDOORBELL
in conjunction with inbound access to NTB MMIO Space, which may hang the
system. To workaround this issue, use one of the memory windows to access the
interrupt and scratch pad registers on the remote system. This bypasses the
issue, but removes one of the memory windows from use by the transport. This
reduction of MWs necessitates adding some logic to determine the number of
available MWs.
Since some NTB usage methodologies may have unidirectional traffic, the ability
to disable the workaround via modparm has been added.
See BF113 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-c5500-c3500-spec-update.pdf
See BT119 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Due to ambiguous documentation, the USD/DSD identification is backward
when compared to the setting in BIOS. Correct the bits to match the
BIOS setting.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The NTB Xeon hardware has 16 scratch pad registers and 16 back-to-back
scratch pad registers. Correct the #define to represent this and update
the variable names to reflect their usage.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
Move error handling into ieee80211_parent_xmitpkt() instead of spreading it
between functions.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3772
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
The system will appear to lockup for long periods of time due to the NTB
driver spending too much time in memcpy. Avoid this by reducing the
number of packets that can be serviced on a given interrupt.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments. For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system. These allocations did
not check for existing buffers and thus did not free them. Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
64bit BAR sizes are permissible with an NTB device. To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.
Also, modify the driver to allow more than 2 Memory Windows.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
->remote_rx_info and ->rx_info are struct ntb_rx_info pointers. If we
add sizeof(struct ntb_rx_info) then it goes too far.
Authored by: Dan Carpenter
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This change fixes some amount of -Wsign-conversion and -Wconversion warnings
and sets correct sizes for some variables (as a result, some loop counters
were touched too).
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3763
