All other mlx5_events report the port number as 1 based, which is how FW
reports it in the port event EQE. Reporting 0 for this event causes
mlx5_ib to not raise a fatal event notification to registered clients
due to a seemingly invalid port.
All switch cases in mlx5_ib_event that go through the port check are
supposed to set the port now, so just do it once at variable
declaration.
Linux commit:
aba462134634b502d720e15b23154f21cfa277e5
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The user can provide very large cqe_size which will cause to integer
overflow.
Linux commit:
28e9091e3119933c38933cb8fc48d5618eb784c8
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Copy small packets like TCP ACKs into a new mbuf
reusing the existing mbuf to receive a new ethernet
frame. This avoids wasting buffer space for
small sized packets.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being defined.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The "priv->pkstats.rx_dropped" is written twice in a row.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Also when the MTU is greater than MCLBYTES.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware queues are deep enough currently and using the DRBR and associated
callbacks only leads to more task switching in the TX path. The is also a race
setting the queue_state which can lead to hung TX rings.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
In last mlx4 update (r325841) we lost the sysctl to show the
firmware version for mlx4 devices.
Add both board identifier and firmware version under:
sys.device.mlx4_core0.hw sysctl node.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
If user input a string larger than the length of buffer, the stack
memory will be corrupted.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Modify QP can fail and it can be acceptable, like when moving from RST to
ERR state, all the rest are not acceptable and a message to the log
should be printed.
The current code prints on all failures and many messages like:
"Failed to modify QP to ERROR state" appear, even when supported by the
state machine of the QP object.
Linux commit:
5dc78ad1904db597bdb4427f3ead437aae86f54c
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
When a packet needs fragmentation, it might generate more than 3 fragments.
With the queue length 3, all fragments are generated faster than the
queue is drained, which effectively drops fourth and later fragments on
the floor.
Submitted by: kib@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
When changing the MTU of ibX network interfaces, check that the MTU was really
changed before requesting an update of the multicast rules. Else we might go
into an infinite loop joining and leaving ibX multicast groups towards the
opensm master interface.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
It is not enough to set ifnet->if_mtu to change the interface MTU.
System saves the MTU for route in the radix tree, and route cache keeps
the interface MTU as well. Since addition of the multicast group causes
recalculation of MTU, even bringing the interface up changes MTU from
4042 to 1500, which makes the system configuration inconsistent. Worse,
ip_output() prefers route MTU over interface MTU, so large packets are
not fragmented and dropped on floor.
Fix it for ipoib(4) using the same approach (or hack) as was applied
for it_tun/if_tap in r339012. Thanks to bz@ for giving the hint.
Submitted by: kib@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Binding to a loopback device is not allowed. Make sure the destination
device address is global by clearing the bound device interface.
Only do this conditionally, else link local addresses won't work.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
A couple of places in the CM do
spin_lock_irq(&cm_id_priv->lock);
...
if (cm_alloc_response_msg(work->port, work->mad_recv_wc, &msg))
However when the underlying transport is RoCE, this leads to a sleeping function
being called with the lock held - the callchain is
cm_alloc_response_msg() ->
ib_create_ah_from_wc() ->
ib_init_ah_from_wc() ->
rdma_addr_find_l2_eth_by_grh() ->
rdma_resolve_ip()
and rdma_resolve_ip() starts out by doing
req = kzalloc(sizeof *req, GFP_KERNEL);
not to mention rdma_addr_find_l2_eth_by_grh() doing
wait_for_completion(&ctx.comp);
to wait for the task that rdma_resolve_ip() queues up.
Fix this by moving the AH creation out of the lock.
Linux commit:
c76161181193985087cd716fdf69b5cb6cf9ee85
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Trying to validate loopback fails because rtalloc1() resolves system
local addresses to the loopback network interface, lo0. Fix this by
explicitly checking for loopback during validation of the source
and destination network address. If the source address belongs to
a local network interface and is equal to the destination address,
there is no need to run the destination address through rtalloc1().
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The master network interface and the VLANs may reside in different VNETs.
Make sure that all VNETs are searched when scanning for GID entries.
Submitted by: netapp
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This prevents code from accepting RoCEv1 connections when
only ROCEv2 is enabled and vice versa.
Linux commit:
0c4386ec77cfcd0ccbdbe8c2e67dd3a49b2a4c7f
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The array ib_mad_mgmt_class_table.method_table has MAX_MGMT_CLASS
(80) elements. Hence compare the array index with that value instead
of with IB_MGMT_MAX_METHODS (128). This patch avoids that Coverity
reports the following:
Overrunning array class->method_table of 80 8-byte elements at element index 127
(byte offset 1016) using index convert_mgmt_class(mad_hdr->mgmt_class)
(which evaluates to 127).
Linux commit:
2fe2f378dd45847d2643638c07a7658822087836
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The port number in the listen_id_priv has been observed to be zero which
means no port has been selected. The current code lacks a check for invalid
port number.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently we always return false if for PCI offline query.
Try to read PCI config, if the return value if 0xffff probably the
PCI is offline.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Make sure we hold a reference on the character device for every opened file
to prevent the character device to be freed prematurely.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Changelist:
- Replace netmap passthrough host support with a more general
mechanism to call TXSYNC/RXSYNC from an in-kernel event-loop.
No kernel threads are used to use this feature: the application
is required to spawn a thread (or a process) and issue a
SYNC_KLOOP_START (NIOCCTRL) command in the thread body. The
kernel loop is executed by the ioctl implementation, which returns
to userspace only when a different thread calls SYNC_KLOOP_STOP
or the netmap file descriptor is closed.
- Update the if_ptnet driver to cope with the new data structures,
and prune all the obsolete ptnetmap code.
- Add support for "null" netmap ports, useful to allocate netmap_if,
netmap_ring and netmap buffers to be used by specialized applications
(e.g. hypervisors). TXSYNC/RXSYNC on these ports have no effect.
- Various fixes and code refactoring.
Sponsored by: Sunny Valley Networks
Differential Revision: https://reviews.freebsd.org/D18015
The getdtablecount.c file won't compile on Linux but it seems like none of
the bootstrap tools actually need it.
Reviewed By: emaste, brooks
Differential Revision: https://reviews.freebsd.org/D14244
newvers.sh runs mkfifo which did not exist before this change.
However, I didn't notice before because it is run from a function
where a missing command does cause a noticeable failure.
Reviewed By: emaste, markj
Differential Revision: https://reviews.freebsd.org/D18377
- don't relocate jump slots multiple times (if LD_BIND_NOW is defined).
- process only R_AARCH64_JUMP_SLOT here, other relocation types are handled
by reloc_plt().
MFC after: 1 week
