/usr/share/examples/etc/bsd-style-copyright. I've fixed a
few minor wording and formatting differences.
Approved by: matk, Hannu Savolainen <hannu@opensound.com>
Reviewed by: imp
We can't bind to a CPU which is not yet on-line, so add code that wait for
CPUs to go on-line before binding to them.
Reported by: Alin-Adrian Anton <aanton@spintech.ro>
MFC after: 2 weeks
configured and that in turn controls the descriptor layout; the rate
control module has no business peeking inside the descriptor but until
we can change the api so the driver records the tx rates and passes
them deal with it
unsolicited pin sense event and need manual control to turn off speaker
volume while attaching headphone.
Tested by: Ingeborg Hellemo <Ingeborg.Hellemo@cc.uit.no>
Disable global Acer + ALC883 headphone automute settings since there are
few models that does not respect this and causing broken behaviour.
Reported/Tested by: Pavel Argentov <argentoff@rtelekom.ru>
When the disk has an error, it will now print SMART
instead of 'Unknown CMD'.
PR: kern/93368
Submitted by: Garry Belka <garry at NetworkPhysics dot COM>
Approved by: sos
firmware in that module (eventhough this is a programming error) - drop the
reference to the module again.
Submitted by: Benjamin Close
MFC after: 3 days
the space allocated for the double fault handler since this space
is otherwise unused till the time a double fault occurs.
This change should have been committed alongside r1.127 of
"exception.S", but I somehow missed doing so.
Problem reported by: jeff
Pointy hat to: jkoshy
not used in any of our code. Also remove explicit padding variable that
kept the bpf_d structure the same size before and after the change in
select implementation, since binary compatibility is not required for this
data structure on 7-CURRENT.
IPv6 over point-to-point gif(4) tunnels.
These revisions caused a host route to the destination of a
point-to-point gif(4) interface to not get installed when the interface
and destination addresses were assigned. This caused
"no route to host" errors when trying to send traffic over the
interface. The first packet arriving inbound over the tunnel,
however, would cause the correct route to get installed, allowing
subsequent outbound traffic to be routed correctly.
gif(4) interfaces with prefix lengths of less than 128 bits
(i.e. no explicit destination address assigned) were not affected
by this bug.
This bug fix is a possible candidate for a 6.2-RELEASE errata note.
Approved by: jhay (original committer)
Discussed with: jhay, JINMEI Tatuya
MFC after: 3 days
blade systems, such as the Dell 1955 and the Intel SBXD132.
Development hardware for this work was provided by Broadcom and iXsystems.
A SBXD132 blade for testing was provided by Iron Systems.
is replaced with BSD gzip, let's make it possible to
distinguish between the two with a __FreeBSDversion bump,
just in case some developers want it.
Suggested by: linimon
NetBSD version is a feature-to-feature re-implementation of GNU
gzip using the freely-redistributable zlib and this version is
expected to be mostly bug-to-bug compatible with the GNU
implementation.
- Because this is a piece of mature code and we want to make
changes so it is added directly rather than importing to
src/contrib.
- Connect newly added code to src/usr.bin/ and rescue/rescue
build.
- Disconnect the GNU gzip code from build for now, they will
be eventually removed completely.
- Provide two new src.conf(5) knobs, WITHOUT_BZIP2_SUPPORT and
WITHOUT_BZIP2.
Tested by: kris (full exp-7 pointyhat build)
Approved by: core (importing a 4-clause BSD licensed file)
Approved by: re (adding new utility during -HEAD code slush)
o Remove ttyyX, created by the obsolete zs(4)
o Replace ttydX by ttyuX, which is created by uart(4)
o Enable ttyu0 as a console to better support the xserve.
MFC after: 1 week
minimize IPIs and rescheduling when scheduling like tasks while keeping
latency low for important threads.
1) An idle thread is running.
2) The current thread is worse than realtime and the new thread is
better than realtime. Realtime to realtime doesn't preempt.
3) The new thread's priority is less than the threshold.
official gnu configure scripts and a couple of other places.
Add an example noisy, loud and annoying placeholder for /usr/bin/objformat
if it turns out to too much trouble to be gone. It is not connected to
the build yet.
