Otherwise the initial call to set_top_of_stack(), which occurs before
fpuinit() sets the correct value for cpu_max_ext_state_size, leaves the
stack base at an incorrect location. Then, when the full area is
zeroed, we end up erroneously zeroing part of the following page.
Reviewed by: kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D24754
causes so_reuseport_lb_test to fail since it slows down how quickly the program runs until the timeout occurs
and fails the test
Sponsored by: Netflix inc.
Differential Revision: https://reviews.freebsd.org/D24747
This is a general cleanup of the relocatable kernel support on powerpc,
needed to enable kernel ifuncs.
* Fix some relocatable issues in the kernel linker, and change to using
a RELOCATABLE_KERNEL #define instead of #ifdef __powerpc__ for parts that
other platforms can use in the future if they wish to have ET_DYN kernels.
* Get rid of the DB_STOFFS hack now that the kernel is relocated to the DMAP
properly across the board on powerpc64.
* Add powerpc64 and powerpc32 ifunc functionality.
* Allow AIM64 virtual mode OF kernels to run from the DMAP like other AIM64
by implementing a virtual mode restart. This fixes the runtime address on
PowerMac G5.
* Fix symbol relocation problems on post-relocation kernels by relocating
the symbol table.
* Add an undocumented method for supplying kernel symbols on powernv and
other powerpc machines using linux-style kernel/initrd loading -- If
you pass the kernel in as the initrd as well, the copy resident in initrd
will be used as a source for symbols when initializing the debugger.
This method is subject to removal once we have a better way of doing this.
Approved by: jhibbits
Relnotes: yes
Sponsored by: Tag1 Consulting, Inc.
Differential Revision: https://reviews.freebsd.org/D23156
Those function are use to map/unmap io region of a pci device.
Different resource can be mapped depending on the bar so use a
tailq to store them all.
Sponsored-by: The FreeBSD Foundation
Reviewed by: emaste, hselasky
Differential Revision: https://reviews.freebsd.org/D24696
The attach method uses GPIO_GET_BUS() to get a "newbus" device
that provides a pin. But on hints-based systems a GPIO controller
driver might not be fully initialized yet and it does not know gpiobus
hanging off it. Thus, GPIO_GET_BUS() cannot be called yet.
The reason is that controller drivers typically create a child gpiobus
using gpiobus_attach_bus() and that leads to the following call chain:
gpiobus_attach_bus() -> gpiobus_attach() ->
bus_generic_attach(gpiobus) -> gpioiic_attach().
So, gpioiic_attach() is called before gpiobus_attach_bus() returns.
I observed this bug with nctgpio driver on amd64.
I think that the problem was introduced in r355276.
The fix is to avoid calling GPIO_GET_BUS() from the attach method.
Instead, we know that on hints-based systems only the parent gpiobus can
provide the pins.
Nothing is changed for FDT-based systems.
MFC after: 1 week
Sometimes, especially when there is not much memory in the system left,
allocating mbuf jumbo clusters (like 9KB or 16KB) can take a lot of time
and it is not guaranteed that it'll succeed. In that situation, the
fallback will work, but if the refill needs to take a place for a lot of
descriptors at once, the time spent in m_getjcl looking for memory can
cause system unresponsiveness due to high priority of the Rx task. This
can also lead to driver reset, because Tx cleanup routine is being
blocked and timer service could detect that Tx packets aren't cleaned
up. The reset routine can further create another unresponsiveness - Rx
rings are being refilled there, so m_getjcl will again burn the CPU.
This was causing NVMe driver timeouts and resets, because network driver
is having higher priority.
Instead of 16KB jumbo clusters for the Rx buffers, 9KB clusters are
enough - ENA MTU is being set to 9K anyway, so it's very unlikely that
more space than 9KB will be needed.
However, 9KB jumbo clusters can still cause issues, so by default the
page size mbuf cluster will be used for the Rx descriptors. This can have a
small (~2%) impact on the throughput of the device, so to restore
original behavior, one must change sysctl "hw.ena.enable_9k_mbufs" to
"1" in "/boot/loader.conf" file.
As a part of this patch (important fix), the version of the driver
was updated to v2.1.2.
Submitted by: cperciva
Reviewed by: Michal Krawczyk <mk@semihalf.com>
Reviewed by: Ido Segev <idose@amazon.com>
Reviewed by: Guy Tzalik <gtzalik@amazon.com>
MFC after: 3 days
PR: 225791, 234838, 235856, 236989, 243531
Differential Revision: https://reviews.freebsd.org/D24546
a few extra arguments). Recently that changed to only have one arg extra so
that two ifdefs around the call are no longer needed. Lets take out the
extra ifdef and arg.
Sponsored by: Netflix Inc
Differential Revision: https://reviews.freebsd.org/D24736
Create rib_lookup() wrapper around per-af dataplane lookup functions.
This will help in the cases of having control plane af-agnostic code.
Switch ifa_ifwithroute() to use this function instead of rtalloc1().
Reviewed by: ae
Differential Revision: https://reviews.freebsd.org/D24731
The bus is independent of the device, so all devices can be attached to
either a PCI bus or an MMIO bus. For example, QEMU's virtio-rng-device
gives the MMIO variant of virtio-rng-pci, and is now detected.
Reviewed by: andrew, br, brooks (mentor)
Approved by: andrew, br, brooks (mentor)
Differential Revision: https://reviews.freebsd.org/D24730
The non-legacy virtio MMIO specification drops the use of PFNs and
replaces them with physical addresses. Whilst many implementations are
so-called transitional devices, also implementing the legacy
specification, TinyEMU[1] does not. Device-specific configuration
registers have also changed to being little-endian, and must be accessed
using a single aligned access for registers up to 32 bits, and two
32-bit aligned accesses for 64-bit registers.
[1] https://bellard.org/tinyemu/
Reviewed by: br, brooks (mentor)
Approved by: br, brooks (mentor)
Differential Revision: https://reviews.freebsd.org/D24681
With the removal of in-tree consumers of DES, Triple DES, and
MD5-HMAC, the only algorithm this driver still supports is SHA1-HMAC.
This is not very useful as a standalone algorithm (IPsec AH-only with
SHA1 would be the only user).
This driver has also not been kept up to date with the original driver
in OpenBSD which supports a few more cards and AES-CBC on newer cards.
The newest card currently supported by this driver was released in
2005.
Reviewed by: cem
MFC after: 1 week
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24691
This has the same reasoning as described in r357048.
Remove a stray declaration while here.
Reported and tested by: trasz
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
locore constructs an L2 page mapping the kernel and preloaded data
starting a KERNBASE (the same as VM_MIN_KERNEL_ADDRESS on arm64).
initarm() and pmap_bootstrap() use the preloaded metadata to
tell it where it can start allocating from.
pmap_bootstrap() currently iterates over the L2 page to find the last
valid entry, but doesn't do anything with the result. Remove the loop
and zap some now-unused local variables.
MFC after: 2 weeks
Sponsored by: Juniper Networks, Klara Inc.
Differential Revision: https://reviews.freebsd.org/D24559
The NFS function called newnfs_trimleading() has not been used by the
code in long time. To give you a clue, it still had a K&R style function
declaration.
Delete it, since it is just cruft, as a part of the NFS mbuf handling
cleanup in preparation for adding ext_pgs mbuf support.
The ext_pgs mbuf support for the build/send side is needed by
nfs-over-tls.
look at when generating a SACK. This was wrong in case of sequence
numbers wrap arounds.
Thanks to Gwenael FOURRE for reporting the issue for the userland stack:
https://github.com/sctplab/usrsctp/issues/462
MFC after: 3 days
Only _BCL and _BCM methods seem to be essential to the driver's
operation. If _BQC is missing then we can assume that the current
brightness is whatever we set by the last _BCM invocation. If _DCS or
_DGS is missing the we can make assumptions as well.
The change is based on a patch suggested by Anthony Jenkins
<Scoobi_doo@yahoo.com> in PR 207086.
PR: 207086
Submitted by: Anthony Jenkins <Scoobi_doo@yahoo.com (earlier version)
Reviewed by: manu
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D24653
r360514 prepared the NFS code for changes to handle ext_pgs mbufs on
the receive side. However, at this time, KERN_TLS does not pass
ext_pgs mbufs up through soreceive(). As such, as this time, only
the send/build side of the NFS mbuf code needs to handle ext_pgs mbufs.
Revert r360514 since the rather extensive changes required for receive
side ext_pgs mbufs are not yet needed.
This avoids unnecessary churn of the sources.
Save and restore (also known as suspend and resume) permits a snapshot
to be taken of a guest's state that can later be resumed. In the
current implementation, bhyve(8) creates a UNIX domain socket that is
used by bhyvectl(8) to send a request to save a snapshot (and
optionally exit after the snapshot has been taken). A snapshot
currently consists of two files: the first holds a copy of guest RAM,
and the second file holds other guest state such as vCPU register
values and device model state.
To resume a guest, bhyve(8) must be started with a matching pair of
command line arguments to instantiate the same set of device models as
well as a pointer to the saved snapshot.
While the current implementation is useful for several uses cases, it
has a few limitations. The file format for saving the guest state is
tied to the ABI of internal bhyve structures and is not
self-describing (in that it does not communicate the set of device
models present in the system). In addition, the state saved for some
device models closely matches the internal data structures which might
prove a challenge for compatibility of snapshot files across a range
of bhyve versions. The file format also does not currently support
versioning of individual chunks of state. As a result, the current
file format is not a fixed binary format and future revisions to save
and restore will break binary compatiblity of snapshot files. The
goal is to move to a more flexible format that adds versioning,
etc. and at that point to commit to providing a reasonable level of
compatibility. As a result, the current implementation is not enabled
by default. It can be enabled via the WITH_BHYVE_SNAPSHOT=yes option
for userland builds, and the kernel option BHYVE_SHAPSHOT.
Submitted by: Mihai Tiganus, Flavius Anton, Darius Mihai
Submitted by: Elena Mihailescu, Mihai Carabas, Sergiu Weisz
Relnotes: yes
Sponsored by: University Politehnica of Bucharest
Sponsored by: Matthew Grooms (student scholarships)
Sponsored by: iXsystems
Differential Revision: https://reviews.freebsd.org/D19495
1) When BBR retransmits the syn it was messing up the snd_max
2) When we need to send a RST we might not send it when we should
Reported by: ankitraheja09@gmail.com
Sponsored by: Netflix.com
Differential Revision: https://reviews.freebsd.org/D24693
This makes it easier to maintain these functions as algorithms are
added or removed.
Reviewed by: cem
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24668
This was only triggered when setting the IPPROTO_TCP level socket
option TCP_DELACK.
This issue was found by runnning an instance of SYZKALLER.
Reviewed by: rrs
Sponsored by: Netflix, Inc.
Differential Revision: https://reviews.freebsd.org/D24690
have been made in rack and adds a few fixes in BBR. This also
removes any possibility of incorrectly doing OOB data the stacks
do not support it. Should fix the skyzaller crashes seen in the
past. Still to fix is the BBR issue just reported this weekend
with the SYN and on sending a RST. Note that this version of
rack can now do pacing as well.
Sponsored by:Netflix Inc
Differential Revision:https://reviews.freebsd.org/D24576
if it can support the PRUS option (OOB). And then have
the new function call that to validate and give the
correct error response if needed to the user (rack
and bbr do not support obsoleted OOB data).
Sponsoered by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D24574
Eliminate the last rtalloc1() call to finish transition to the new routing
KPI defined in r359823.
Differential Revision: https://reviews.freebsd.org/D24663
After converting routing subsystem customers to use nexthop objects
defined in r359823, some fields in struct rtentry became unused.
This commit removes rt_ifp, rt_ifa, rt_gateway and rt_mtu from struct rtentry
along with the code initializing and updating these fields.
Cleanup of the remaining fields will be addressed by D24669.
This commit also changes the implementation of the RTM_CHANGE handling.
Old implementation tried to perform the whole operation under radix WLOCK,
resulting in slow performance and hacks like using RTF_RNH_LOCKED flag.
New implementation looks up the route nexthop under radix RLOCK, creates new
nexthop and tries to update rte nhop pointer. Only last part is done under
WLOCK.
In the hypothetical scenarious where multiple rtsock clients
repeatedly issue RTM_CHANGE requests for the same route, route may get
updated between read and update operation. This is addressed by retrying
the operation multiple (3) times before returning failure back to the
caller.
Differential Revision: https://reviews.freebsd.org/D24666
"F lock" is a switch between two sets of scancodes for function keys F1-F12
found on some Logitech and Microsoft PS/2 keyboards [1]. When "F lock" is
pressed, then F1-F12 act as function keys and produce usual keyscans for
these keys. When "F lock" is depressed, F1-F12 produced the same keyscans
but prefixed with E0.
Some laptops use [2] E0-prefixed F1-F12 scancodes for non-standard keys.
[1] https://www.win.tue.nl/~aeb/linux/kbd/scancodes-6.html
[2] https://reviews.freebsd.org/D21565
MFC after: 2 weeks
While there, remove ifdef around cs_target check in cfiscsi_ioctl_list().
I am not sure why this ifdef was added, but without this check code will
crash below on NULL dereference.
Submitted by: Aleksandr Fedorov <aleksandr.fedorov@itglobal.com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D24587
run it). Make sure that we do. Simplify the flow a bit, and fix a
comment since we do need to do these things.
Noticed by: cperciva (not sure why my invariants kernel didn't trigger)
They have more differencies than similarities. For now there is lots
of code that would check for M_EXT only and work correctly on M_EXTPG
buffers, so still carry M_EXT bit together with M_EXTPG. However,
prepare some code for explicit check for M_EXTPG.
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24598
o Shrink sglist(9) functions to work with multipage mbufs down from
four functions to two.
o Don't use 'struct mbuf_ext_pgs *' as argument, use struct mbuf.
o Rename to something matching _epg.
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24598
next commit brings in second flag, so let them already be in the
future namespace.
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24598
but we need buffer of MLEN bytes. This isn't just a simplification,
but important fixup, because previous commit shrinked sizeof(struct
mbuf) down below MSIZE, and instantiating an mbuf on stack no longer
provides enough data.
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24598
The following series of patches addresses three things:
Now that array of pages is embedded into mbuf, we no longer need
separate structure to pass around, so struct mbuf_ext_pgs is an
artifact of the first implementation. And struct mbuf_ext_pgs_data
is a crutch to accomodate the main idea r359919 with minimal churn.
Also, M_EXT of type EXT_PGS are just a synonym of M_NOMAP.
The namespace for the newfeature is somewhat inconsistent and
sometimes has a lengthy prefixes. In these patches we will
gradually bring the namespace to "m_epg" prefix for all mbuf
fields and most functions.
Step 1 of 4:
o Anonymize mbuf_ext_pgs_data, embed in m_ext
o Embed mbuf_ext_pgs
o Start documenting all this entanglement
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24598
- Make ctl_add_lun() synchronous. Asynchronous addition was used by
Copan's proprietary code long ago and never for upstream FreeBSD.
- Move LUN enable/disable calls from backends to CTL core.
- Serialize LUN modification and partially removal to avoid double frees.
- Slightly unify backends code.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This removes support for the following algorithms:
- ARC4
- Blowfish
- CAST128
- DES
- 3DES
- MD5-HMAC
- Skipjack
Since /dev/crypto no longer supports 3DES, stop testing the 3DES KAT
vectors in cryptotest.py.
Reviewed by: cem (previous version)
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24346
The changes in r359374 added various sanity checks in sessions and
requests created by crypto consumers in part to permit backend drivers
to make assumptions instead of duplicating checks for various edge
cases. One of the new checks was to reject sessions which provide a
pointer to a key while claiming the key is zero bits long.
IPsec ESP tripped over this as it passes along whatever key is
provided for NULL, including a pointer to a zero-length key when an
empty string ("") is used with setkey(8). One option would be to
teach the IPsec key layer to not allocate keys of zero length, but I
went with a simpler fix of just not passing any keys down and always
using a key length of zero for NULL algorithms.
PR: 245832
Reported by: CI
Examples of depecrated algorithms in manual pages and sample configs
are updated where relevant. I removed the one example of combining
ESP and AH (vs using a cipher and auth in ESP) as RFC 8221 says this
combination is NOT RECOMMENDED.
Specifically, this removes support for the following ciphers:
- des-cbc
- 3des-cbc
- blowfish-cbc
- cast128-cbc
- des-deriv
- des-32iv
- camellia-cbc
This also removes support for the following authentication algorithms:
- hmac-md5
- keyed-md5
- keyed-sha1
- hmac-ripemd160
Reviewed by: cem, gnn (older verisons)
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24342
The addition of the HSM SBI extension to OpenSBI introduces a new
breaking change: secondary harts will remain parked in the firmware,
until they are brought up explicitly via sbi_hsm_hart_start(). Add
the call to do this, sending the secondary harts to mpentry.
If the HSM extension is not present, secondary harts are assumed to be
released by the firmware, as is the case for OpenSBI =< v0.6 and BBL.
In the case that the HSM call fails we exclude the CPU, notify the
user, and allow the system to proceed with booting.
Reviewed by: markj (older version)
Differential Revision: https://reviews.freebsd.org/D24497
APs enter the kernel at the same point as the BSP, the _start routine.
They then jump to mpentry, but not before storing the kernel's physical
load address in the s9 register. Extract this calculation into its own
routine, so that APs can be instructed to enter directly from mpentry.
Differential Revision: https://reviews.freebsd.org/D24495
All callers are currently filtering bad nsid to this function,
however, we'll have undefined behavior if that's not true. Add the
KASSERT to prevent that.
Previously procctl(PROC_PROTMAX_STATUS, ... used the PROC_ASLR_NOFORCE
macro for the "system-wide configured policy" status, instead of
PROC_PROTMAX_NOFORCE.
They both have a value of 3, so no functional change.
Sponsored by: The FreeBSD Foundation
Factoring some of the code in nfsm_dissct() out into separate functions
allows these functions to be used elsewhere in the NFS mbuf handling code.
Other uses of these functions will be done in future commits.
It also makes it easier to add support for ext_pgs mbufs, which is needed
for nfs-over-tls under development in base/projects/nfs-over-tls.
Although the algorithm in nfsm_dissct() is somewhat re-written by this
patch, the semantics of nfsm_dissct() should not have changed.
- maxio should be dp->d_maxsize. This is often MAXPHYS, but not always
(especially if MAXPHYS is > 1MB).
- Unlock the periph before returning. We don't need to relock it to
release the ccb.
- Make sure we release the ccb in error paths.
Reviewed by: cperciva
With a length of 16, the name ("<if name>:TX(<qid>):callout") typically
gets truncated.
PR: 245712
Reported by: ghuckriede@blackberry.com
MFC after: 1 week
Running TCP Cubic together with ECN could end up reducing cwnd down to 1 byte, if the
receiver continously sets the ECE flag, resulting in very poor transmission speeds.
In line with RFC6582 App. B, a lower bound of 2 MSS is introduced, as well as a typecast
to prevent any potential integer overflows during intermediate calculation steps of the
adjusted cwnd.
Reported by: Cheng Cui
Reviewed by: tuexen (mentor)
Approved by: tuexen (mentor)
MFC after: 2 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D23353
With these two ioctls implemented in the nda driver, nvmecontrol now
works with nda just like it does with nvd. It eliminates the need to
jump through odd hoops to get this data.
Add the nvmeX device to the XPT_PATH_INQ nvme specific
information. while one could figure this out by looking up the
domain🚌slot:function, it's a lot easier to have the SIM set it
directly since the sim knows this.
which can cause a TCP client to use invalid or stale TCP sequence numbers for ACK packets.
Packets with old sequence numbers are ignored and not used to update the send window size.
This might cause the TCP session to hang indefinitely under some circumstances.
Reported by: Cui Cheng
Reviewed by: tuexen (mentor), rgrimes (mentor)
Approved by: tuexen (mentor), rgrimes (mentor)
MFC after: 3 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D24515
Continue routing subsystem conversion to nhop objects defined in r359823.
Use fields from nhop structure instead of "struct rtentry" fields.
This is one of the last changes prior to removing rt_ifp, rt_ifa,
rt_gateway and rt_mtu from struct rtentry.
Differential Revision: https://reviews.freebsd.org/D24609
by not including the SYN bit sequence space in cwnd related calculations.
Snd_und is adjusted explicitly in all cases, outside the cwnd update, instead.
This fixes an off-by-one conformance issue with regular TCP sessions not
using Appropriate Byte Counting (RFC3465), sending one more packet during
the initial window than expected.
PR: 235256
Reviewed by: tuexen (mentor), rgrimes (mentor)
Approved by: tuexen (mentor), rgrimes (mentor)
MFC after: 3 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D19000
With the upcoming multipath changes described in D24141,
rt->rt_nhop can potentially point to a nexthop group instead of
an individual nhop.
To simplify caller handling of such cases, change ifa_rtrequest() callback
to pass changed nhop directly.
Differential Revision: https://reviews.freebsd.org/D24604
Openfirmare enumerates and installs the driver for all processors,
regardless of whether they will be started later (because of power
constrains for example).
MFC after: 3 weeks
Don't set initial voltage for regulators having their voltage already
in allowed range. As side effect of this change, we don't try to set
initial voltage for fixed voltage regulators - these don't have impemented
voltage set method so their initialization has always failed.
MFC after: 3 weeks
- always initialize selector of voltage signaling standard.
Various versions of U-boot leaves voltage signaling standard settings
for PMUIO2 domain in different state. Always initialize it
into expected state.
- start the driver as early as possible, the IO domains should be
initialized before other drivers are attached.
- rename RK3399 register to its name founds in TRM.
This is the second part of fixes for serial port corruption observed after
DT 5.6 import.
Reviewed by: manu
MFC after: 1 week
Currently functionality resides in rtsock.c, which is a controlling
interface, partially external to the routing subsystem.
Additionally, DDB-supporting functionality is > 100SLOC, which deserves
a separate file.
Given that, move this functionality to a newly-created net/route/ subdir.
Reviewed by: cem
Differential Revision: https://reviews.freebsd.org/D24561
Nexthop objects implementation, defined in r359823,
introduced sys/net/route directory intended to hold all
routing-related code. Move recently-introduced route_temporal.c and
private route_var.h header there.
Differential Revision: https://reviews.freebsd.org/D24597
One of the goals of the new routing KPI defined in r359823
is to entirely hide`struct rtentry` from the consumers.
It will allow to improve routing subsystem internals and deliver
features much faster.
This is one of the last changes, effectively moving struct rtentry
definition to a net/route_var.h header, internal to the routing subsystem.
Differential Revision: https://reviews.freebsd.org/D24580
Otherwise, since the CV is not signalled until data is drained from the
socket, it is trivial to create an unkillable process using
sendfile(SF_SYNC) and a process-private PF_LOCAL socket pair. In
particular, the cv_wait() in sendfile() does not get interrupted until
data is drained from the receiving socket buffer.
Reported by: pho
Discussed with: kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
A concurrent unlocked lookup can wire the page after
vm_page_release_locked() releases the last wiring, in which case
vm_page_release_locked() must not free the page. Once the xbusy lock is
acquired, that, the object lock and the fact that the page is unmapped
ensure that the wire count cannot increase, so re-check for new wirings
after the page is xbusied.
Update the comment above vm_page_wired() to reflect the new
synchronization rules.
Reported by: glebius
Reviewed by: alc, jeff, kib
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D24592
New fib[46]_lookup() functions support multipath transparently.
Given that, switch the last rtalloc_mpath_fib() calls to
dib4_lookup() and eliminate the function itself.
Note: proper flowid generation (especially for the outbound traffic) is a
bigger topic and will be handled in a separate review.
This change leaves flowid generation intact.
Differential Revision: https://reviews.freebsd.org/D24595
r360292 switched most of the remaining routing customers to a new KPI,
leaving a bunch of wrappers for old routing lookup functions unused.
Remove them from the tree as a part of routing cleanup.
Differential Revision: https://reviews.freebsd.org/D24569
This debugging code printing routing table data was introduced in rS25723,
22+ years ago. The last functional commit to this code was rS67534, 19 years ago.
The code has been turned off by default all this time.
Lastly, this code directly iterates radix tree and rtentries, which is not
not a proper interaction with routing system.
Differential Revision: https://reviews.freebsd.org/D24554
The NFS code had a bunch of Mac OS/X accessor functions named uio_XXX
left over from the port to Mac OS/X. Since that port is long forgotten,
replace the calls with the code generated by the FreeBSD macros for these
in nfskpiport.h. This allows the macros to be deleted from nfskpiport.h
and I think makes the code more readable.
This patch should not result in any semantic change.
This largely reuses the TLS TOE support added in r330884. However,
this uses the KTLS framework in upstream OpenSSL rather than requiring
Chelsio-specific patches to OpenSSL. As with the existing TLS TOE
support, use of RX offload requires setting the tls_rx_ports sysctl.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24453
Without this patch, sosend_generic() will try to use top->m_pkthdr.len,
assuming that the first mbuf has a pkthdr.
When a list of ext_pgs mbufs is passed in, the first mbuf is not a
pkthdr and cannot be post-r359919. As such, the value of top->m_pkthdr.len
is bogus (0 for my testing).
This patch fixes sosend_generic() to handle this case, calculating the
total length via m_length() for this case.
There is currently nothing that hands a list of ext_pgs mbufs to
sosend_generic(), but the nfs-over-tls kernel RPC code in
projects/nfs-over-tls will do that and was used to test this patch.
Reviewed by: gallatin
Differential Revision: https://reviews.freebsd.org/D24568
This was changed in the review process for the flags sysctl. The
reasons for the change are no longer valid as the code changed after
that. Cast the one place where it might make a difference (but I don't
think it does). This restores the ability to see flags for softc in
gdb.
- Add a new TCP_RXTLS_ENABLE socket option to set the encryption and
authentication algorithms and keys as well as the initial sequence
number.
- When reading from a socket using KTLS receive, applications must use
recvmsg(). Each successful call to recvmsg() will return a single
TLS record. A new TCP control message, TLS_GET_RECORD, will contain
the TLS record header of the decrypted record. The regular message
buffer passed to recvmsg() will receive the decrypted payload. This
is similar to the interface used by Linux's KTLS RX except that
Linux does not return the full TLS header in the control message.
- Add plumbing to the TOE KTLS interface to request either transmit
or receive KTLS sessions.
- When a socket is using receive KTLS, redirect reads from
soreceive_stream() into soreceive_generic().
- Note that this interface is currently only defined for TLS 1.1 and
1.2, though I believe we will be able to reuse the same interface
and structures for 1.3.
This patch is intended to solve a specific problem that iavf(4)
encounters, but what it does can be extended to solve other issues.
To summarize the iavf(4) issue, if the PF driver configures VLAN
anti-spoof, then the VF driver needs to make sure no untagged traffic is
sent if a VLAN is configured, and vice-versa. This can be an issue when
a VLAN is being registered or unregistered, e.g. when a packet may be on
the ring with a VLAN in it, but the VLANs are being unregistered. This
can cause that tagged packet to go out and cause an MDD event.
To fix this, include a new interface-dependent function that drivers can
implement named IFDI_NEEDS_RESTART(). Right now, this function is called
in iflib_vlan_unregister/register() to determine whether the interface
needs to be stopped and started when a VLAN is registered or
unregistered. The default return value of IFDI_NEEDS_RESTART() is true,
so this fixes the MDD problem that iavf(4) encounters, since the
interface rings are flushed during a stop/init.
A future change to iavf(4) will implement that function just in case the
default value changes, and to make it explicit that this interface reset
is required when a VLAN is added or removed.
Reviewed by: gallatin@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D22086
Now that hw.machine_arch handles soft-float vs hard-float there is no
longer a reason for this config.
Submitted by: mhorne (kern.mk hunk)
Reviewed by: imp (earlier version), kp
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24544
Instead, copy the strings into a temporary buffer on the stack and
run strcmp on the copies.
Reviewed by: brooks, kib
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24567
For userland, MACHINE_ARCH reflects the current ABI via preprocessor
directives. For the kernel, the hw.machine_arch sysctl uses the ELF
header flags of the current process to select the correct MACHINE_ARCH
value.
Reviewed by: imp, kp
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24543
This extends some of the changes in place to support reporting support
for 32-bit ABIs to permit reporting hard-float vs soft-float ABIs.
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24542
latest rack and bbr in from the NF repo. When those come
in the OOB data handling will be fixed where Skyzaller crashes.
Differential Revision: https://reviews.freebsd.org/D24575
Contrary to the kevent man page, EV_EOF on a fifo is not cleared by
EV_CLEAR. Modify the read and write filters to clear EV_EOF when the
fifo's PIPE_EOF flag is clear, and update the man page to document the
new behaviour.
Modify the write filter to return the amount of buffer space available
even if no readers are present. This matches the behaviour for sockets.
When reading from a pipe, only call pipeselwakeup() if some data was
actually read. This prevents the continuous re-triggering of a
EVFILT_READ event on EOF when in edge-triggered mode.
PR: 203366, 224615
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D24528
This ensures that pipe_poll() and the pipe kqueue filters observe
PIPE_EOF and set EV_EOF accordingly. As a result an extra call to
knote() after setting PIPE_EOF is unnecessary.
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D24528
Previously we allocated a separate VM object for each kernel stack.
However, fully constructed kernel stacks are cached by UMA, so there is
no harm in using a single global object for all stacks. This reduces
memory consumption and makes it easier to define a memory allocation
policy for kernel stack pages, with the aim of reducing physical memory
fragmentation.
Add a global kstack_object, and use the stack KVA address to index into
the object like we do with kernel_object.
Reviewed by: kib
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D24473
Some models of laptops e.g. "X1 Carbon 3rd Gen Thinkpad" have LRM buttons
wired as so called "Synaptic touchpads extended buttons" rather thah real
trackpoint buttons. Handle this case with merging of events from both
sources.
PR: 245877
Reported by: Raichoo <raichoo@googlemail.com>
MFC after: 1 week
Introduce new fib[46]_lookup_debugnet() functions serving as a
special interface for the crash-time operations. Underlying
implementation will try to return lookup result if
datastructures are not corrupted, avoding locking.
Convert debugnet to use fib4_lookup_debugnet() and switch it
to use nexthops instead of rtentries.
Reviewed by: cem
Differential Revision: https://reviews.freebsd.org/D24555
It was broken by r360292 as fib6_lookup() assumes de-embedded addresses
while rtalloc_mpath_fib() requires sockaddr with embedded ones.
New fib6_lookup() transparently supports multipath, hence
remove old RADIX_MPATH condition.
The pf_frag_mtx mutex protects the fragments queue. The fragments queue
is virtualised already (i.e. per-vnet) so it makes no sense to block
jail A from accessing its fragments queue while jail B is accessing its
own fragments queue.
Virtualise the lock for improved concurrency.
Differential Revision: https://reviews.freebsd.org/D24504
Run the bridge datapath under epoch, rather than under the
BRIDGE_LOCK().
We still take the BRIDGE_LOCK() whenever we insert or delete items in
the relevant lists, but we use epoch callbacks to free items so that
it's safe to iterate the lists without the BRIDGE_LOCK.
Tests on mercat5/6 shows this increases bridge throughput significantly,
from 3.7Mpps to 18.6Mpps.
Reviewed by: emaste, philip, melifaro
MFC after: 2 months
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D24250
If we pass an anchor name which doesn't exist pfr_table_count() returns
-1, which leads to an overflow in mallocarray() and thus a panic.
Explicitly check that pfr_table_count() does not return an error.
Reported-by: syzbot+bd09d55d897d63d5f4f4@syzkaller.appspotmail.com
Reviewed by: melifaro
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D24539
r360292 introduced the wrong order, resulting in returned
nhops not being referenced, despite the fact that references
were requested. That lead to random GPF after using SCTP sockets.
Special defined macro like IPV[46]_SCOPE_GLOBAL will be introduced
soon to reduce the chance of putting arguments in wrong order.
Reported-by: syzbot+5c813c01096363174684@syzkaller.appspotmail.com
Release kernels have no KDB backends enabled, so they discard an NMI
if it is not due to a hardware failure. This includes NMIs from
IPMI BMCs and hypervisors.
Furthermore, the interaction of panic_on_nmi, kdb_on_nmi, and
debugger_on_panic is confusing.
Respond to all NMIs according to panic_on_nmi and debugger_on_panic.
Remove kdb_on_nmi. Expand the meaning of panic_on_nmi by making
it a bitfield. There are currently two bits: one for NMIs due to
hardware failure, and one for all others. Leave room for more.
If panic_on_nmi and debugger_on_panic are both true, don't actually panic,
but directly enter the debugger, to allow someone to leave the debugger
and [hopefully] resume normal execution.
Reviewed by: kib
MFC after: 2 weeks
Relnotes: yes: machdep.kdb_on_nmi is gone; machdep.panic_on_nmi changed
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D24558
Store the attached regulator in a tailq to later find them in ofw_map.
While here, do not attempt to attach a regulator without a name, a node
might exists but if it doesn't have a name the regulator is unused.
MFC after: 1 month
